Component guide · Intermediate · 3 min read
Pixhawk and APM Analog Power Modules (PM02, HVPM, CUAV HV_PM, DJI NAZA PM)

Setup
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
An analog power module sits between the flight battery and the drone. It powers the autopilot with a clean 5.3 V and sends voltage and current signals so ArduPilot or PX4 can show battery level and trigger failsafes. APM-style modules handle 2S to 6S at about 90 A; high-voltage modules like the HVPM and CUAV HV_PM handle up to 14S.
Key specs at a glance
- Input
- 2S to 6S (APM, PM02) or 2S to 14S (HVPM, HV_PM)
- Autopilot supply
- About 5.1 to 5.3 V, 3 A
- Current sense
- Up to 60 to 90 A
- Signals
- Analog voltage and current
- Connector
- 6-pin to autopilot POWER port
- Pack plugs
- XT60 or XT90
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1APM/Pixhawk Power Module V6.0 3A BEC XT60 (2-6S, 90A)₹539
Option 2APM/Pixhawk Power Module w/ BEC 3A XT60 28V 90A₹579
Option 3ReadyToSky APM Pixhawk Power Module ESC PDB₹899
Option 4Holybro Power Module PM02₹2,469
Option 5SwiftWing HVPM-01A High Voltage Analog Power Module (2S–14S, 60V) for ArduPilot & PX4₹3,470
Option 6CUAV HV_PM Power Module for V5+ – XT60 Plug₹6,759
What the Pixhawk analog power module is
The Pixhawk analog power module (such as PM02 V3 or APM power module) sits between the battery and the drone, powering the autopilot with clean 5.3 V and sending battery voltage and current as analog signals.
Calibrate in Mission Planner or QGroundControl: measure pack voltage with a meter and enter it, then compare consumed mAh with what the charger puts back, and adjust amps-per-volt.
The module powers only the autopilot. ESCs and motors take power from the PDB, not through the 5 V regulator.
Pixhawk analog power module pinout
The pins on the Pixhawk analog power module and what each one does.
| Pin | Function |
|---|---|
| Battery side | XT60/XT90 from pack |
| Load side | To PDB or ESCs |
| 6-pin | VCC, VCC, current, voltage, GND, GND |
- Battery side
- XT60/XT90 from pack
- Load side
- To PDB or ESCs
- 6-pin
- VCC, VCC, current, voltage, GND, GND
Wiring the Pixhawk analog power module
Connect the Pixhawk analog power module like this.
| Pixhawk analog power module pin | Pixhawk | APM / NAZA |
|---|---|---|
| 6-pin | Pixhawk POWER1 | APM PM port |
| Load | PDB input | PDB input |
- 6-pin
- Pixhawk:
- Pixhawk POWER1
- APM / NAZA:
- APM PM port
- Load
- Pixhawk:
- PDB input
- APM / NAZA:
- PDB input
Example code
A minimal sketch to check the part works.
BATT_MONITOR = 4 (analog voltage and current)
BATT_VOLT_MULT = calibrate with a meter
BATT_AMP_PERVLT = calibrate with charger mAh
BATT_CAPACITY = pack mAhSetup and tuning
battery into the XT60 input, ESCs or PDB on the output, and the 6-pin cable to the autopilot POWER port.
check the maximum voltage (often 2S to 12S) and current (often 60 to 90 A).
select analog voltage and current in the battery monitor settings.
measure battery voltage with a meter and set the voltage divider value; check current with a clamp meter.
the 5.3 V output is only for the autopilot, not servos or other loads.
What you need
Shop this list10 of 10 found in our store · ₹22,980
APM/Pixhawk Power Module V6.0 3A BEC XT60 (2-6S, 90A): the part this guide coversAPM/Pixhawk Power Module V6.0 3A BEC XT60 (2-6S, 90A)₹539
APM/Pixhawk Power Module w/ BEC 3A XT60 28V 90A: another version this guide coversAPM/Pixhawk Power Module w/ BEC 3A XT60 28V 90A₹579
ReadyToSky APM Pixhawk Power Module ESC PDB: another version this guide coversReadyToSky APM Pixhawk Power Module ESC PDB₹899
Holybro Power Module PM02: another version this guide coversHolybro Power Module PM02₹2,469
SwiftWing HVPM-01A High Voltage Analog Power Module (2S–14S, 60V) for ArduPilot & PX4: another version this guide coversSwiftWing HVPM-01A High Voltage Analog Power Module (2S–14S, 60V) for ArduPilot & PX4₹3,470
CUAV HVPM Power Module for V5+ – XT60 Plug: another version this guide coversCUAV HV_PM Power Module for V5+ – XT60 Plug₹6,759
DJI NAZA V2 Power Module | 2-6S BEC & Voltage Monitor: another version this guide coversDJI NAZA V2 Power Module | 2-6S BEC & Voltage Monitor₹5,099
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
Digital watt meter and power analyser: to measure pack currentDigital Watt Meter and Power Analyser₹650
iMAX B6 balance charger: to charge the flight packiMAX B6 Balance Charger₹2,339
Alternatives and when to choose them
- Digital power modules: I2C/CAN, higher accuracy.
- Drone PDB and BEC.
- High-voltage BECs.
Common mistakes to avoid
- Exceeding the module's current rating.
- Powering servos from it.
- Skipping calibration.
- Using it on a digital-only autopilot.
Frequently asked questions
Why is the battery voltage wrong in Mission Planner?
The voltage divider value is not calibrated; set it from a meter reading.
Can the power module power my servos?
No. Its 5.3 V supply is only for the autopilot and small peripherals.
What current can it measure?
Usually up to 60 to 90 A continuous, depending on the model.
Does it work with Pixhawk 6X?
No. The 6X needs a digital power module; use analog modules with analog-input autopilots.
Why is current reading zero?
The current sensor setting or the amps-per-volt value is wrong.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
