Component guide · Intermediate · 3 min read
High-Voltage BECs for 6S to 14S Drones

Matek 12S Pro, Vector, Mauch, Holybro, SIYI)
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Heavy-lift, agricultural and long-range drones run 6S to 14S packs (up to about 59 V), too high for normal UBECs. High-voltage BECs from Matek, Vector Technics, Mauch, Holybro and SIYI take this input and give clean 5 V and 12 V for autopilots, telemetry, cameras and video links. Pick by input range, output voltage and current.
Key specs at a glance
- Input
- About 9 to 60 V (3S to 14S, model dependent)
- Outputs
- 5 V, 5.3 V, 12 V or adjustable
- Current
- 2 A to 12 A
- Mauch 017
- 4S to 6S, 2 x 5.35 V and 1 x 12 V
- Holybro UBEC
- 3S to 14S, 12 A adjustable
- SIYI BEC
- 4S to 18S for HM30 air unit
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Matek Systems 12S Pro BEC – 9-55V Input, 5A Output₹1,729
Option 2Vector Technics BEC 5V 2A DC-DC Converter (6S-12S)₹1,449
Option 3Vector Technics VOLTROX 12V 2A BEC (6-12S)₹1,839
Option 4Mauch 017 PL 4-6S BEC 2×5.35V 1×12.0V Regulator₹9,189
Option 5Holybro UBEC Power Module – 12A Output, 3-14S Input, Adjustable Voltage₹5,539
Option 6SIYI 4-18S BEC Module for HM30 Air Unit₹3,491
What the High-voltage BEC (6S to 14S) is
A high-voltage BEC takes 6S to 14S battery voltage (about 22 to 60 V) and makes a clean 5 V, 9 V or 12 V supply for flight controllers, cameras and video links.
Use two independent BECs for redundancy on expensive aircraft: one for the autopilot, one for payload.
Add input capacitors close to the BEC on long battery leads, as voltage spikes on high-voltage packs can exceed ratings.
High-voltage BEC (6S to 14S) pinout
The pins on the High-voltage BEC (6S to 14S) and what each one does.
| Pin | Function |
|---|---|
| Input + / - | Pack |
| Outputs | 5 V and 12 V leads |
- Input + / -
- Pack
- Outputs
- 5 V and 12 V leads
Wiring the High-voltage BEC (6S to 14S)
Connect the High-voltage BEC (6S to 14S) like this.
| High-voltage BEC (6S to 14S) pin | Autopilot side | Payload side |
|---|---|---|
| Input | From PDB high-voltage pads | Same |
| 5 V out | Autopilot power port or servo rail | Telemetry |
| 12 V out | Camera / video link | Lights |
- Input
- Autopilot side:
- From PDB high-voltage pads
- Payload side:
- Same
- 5 V out
- Autopilot side:
- Autopilot power port or servo rail
- Payload side:
- Telemetry
- 12 V out
- Autopilot side:
- Camera / video link
- Payload side:
- Lights
Example code
A minimal sketch to check the part works.
1. Power from a current-limited supply or smoke stopper first.
2. Measure each output with a multimeter before connecting electronics.
3. Then test on the flight pack.Setup and tuning
check the BEC is rated for the battery's full charge voltage, such as 58.8 V for 14S.
set or pick the output voltage your device needs; most autopilots want 5.3 V.
choose a BEC with margin above the total load.
connect input to the battery leads after the main connector, with a fuse if possible.
add a capacitor on the input and keep the BEC away from GPS and compass.
What you need
Shop this list9 of 9 found in our store · ₹24,677
Matek Systems 12S Pro BEC – 9-55V Input, 5A Output: the part this guide coversMatek Systems 12S Pro BEC – 9-55V Input, 5A Output₹1,729
Vector Technics BEC 5V 2A DC-DC Converter (6S-12S): another version this guide coversVector Technics BEC 5V 2A DC-DC Converter (6S-12S)₹1,449
Vector Technics VOLTROX 12V 2A BEC (6-12S): another version this guide coversVector Technics VOLTROX 12V 2A BEC (6-12S)₹1,839
Mauch 017 PL 4-6S BEC 2×5.35V 1×12.0V Regulator: another version this guide coversMauch 017 PL 4-6S BEC 2×5.35V 1×12.0V Regulator₹9,189
Holybro UBEC Power Module – 12A Output, 3-14S Input, Adjustable Voltage: another version this guide coversHolybro UBEC Power Module – 12A Output, 3-14S Input, Adjustable Voltage₹5,539
SIYI 4-18S BEC Module for HM30 Air Unit: another version this guide coversSIYI 4-18S BEC Module for HM30 Air Unit₹3,491
Matek MICRO BEC 5V/12V-ADJ Voltage Regulator: another version this guide coversMatek MICRO BEC 5V/12V-ADJ Voltage Regulator₹614
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
Digital watt meter and power analyser: to measure pack currentDigital Watt Meter and Power Analyser₹650
Alternatives and when to choose them
- 5V UBEC: up to 6S/8S.
- Heavy-lift drone motors.
- Pixhawk power modules.
Common mistakes to avoid
- Using a BEC rated below full charge voltage.
- Mounting it next to the GPS and compass.
- Sharing one BEC for autopilot and payload.
- Leaving out the input capacitor.
Frequently asked questions
Can I use a 6S BEC on a 12S drone?
No. The input must be rated for the full 12S voltage, about 50.4 V.
What output voltage does a Pixhawk need?
About 5.0 to 5.5 V, usually through a power module or 5.3 V BEC.
Why is my video noisy after adding the BEC?
Switching noise; add an LC filter or move the BEC away from the camera and VTX.
Can one BEC power everything?
Use separate BECs for the autopilot and for payloads so one fault does not down both.
Does a BEC need cooling?
Yes, at high load it warms; mount it in airflow.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
