Component guide · Beginner · 3 min read
5V and 12V UBEC Switching Regulators for Drones and RC (2S to 13S)

Wiring Guide
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
A UBEC (universal battery eliminator circuit) is a switching regulator that takes LiPo pack voltage and makes a steady 5 V, 6 V or 12 V for flight controllers, receivers, servos, gimbals and FPV gear. Pick one by input range (2S to 6S, up to 13S) and output current (3 A to 7 A). Switch-mode UBECs waste little heat compared to linear BECs.
Key specs at a glance
- Input
- 2S to 6S common; some 2S to 8S or 13S
- Output
- 5 V, 6 V, 12 V or switchable
- Current
- 3 A, 5 A, 7 A versions
- Type
- Switching
- Connectors
- Servo lead or pads
- Noise
- Some ripple; add LC filter for analog video
A shorted, over-charged or damaged lithium cell can get very hot and catch fire. Use a protection board or BMS, never short the terminals, charge on a non-flammable surface and do not leave a charging pack alone. Throw away cells that are swollen or dented.
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1UBEC 5V 5A BEC Voltage Regulator₹409
Option 2UBEC 5V/3A Switching Voltage Regulator₹269
Option 3Mini UBEC DC-DC Step Down Converter 3A 5V₹272
Option 42-13S 5V 5A BEC Voltage Regulator Module₹769
Option 52-6S 5V 5A BEC Voltage Regulator for Quadcopter Drones₹959
Option 6UBEC-5V/7A 2-8S 7A DC-DC Voltage Regulator₹519
What the 5V UBEC switching regulator is
A UBEC (universal battery eliminator circuit) is a small switching regulator that turns 2S to 6S battery voltage into a steady 5 or 6 V for receivers, servos and electronics.
Check the input range against your fully charged pack: 6S is 25.2 V, 8S is 33.6 V.
Some UBECs add switching noise to analog FPV video. Power the video transmitter from a filtered source or add an LC filter.
5V UBEC switching regulator pinout
The pins on the 5V UBEC switching regulator and what each one does.
| Pin | Function |
|---|---|
| Input + / - | Pack voltage |
| Output + / - | Regulated output |
| Jumper | Voltage select (some) |
- Input + / -
- Pack voltage
- Output + / -
- Regulated output
- Jumper
- Voltage select (some)
Wiring the 5V UBEC switching regulator
Connect the 5V UBEC switching regulator like this.
| 5V UBEC switching regulator pin | 5 V | 12 V |
|---|---|---|
| Input | PDB or pack leads | Same |
| Output | Flight controller 5V/servo rail | Gimbal 12 V input |
- Input
- 5 V:
- PDB or pack leads
- 12 V:
- Same
- Output
- 5 V:
- Flight controller 5V/servo rail
- 12 V:
- Gimbal 12 V input
Example code
A minimal sketch to check the part works.
1. Power from a current-limited supply or smoke stopper first.
2. Measure each output with a multimeter before connecting electronics.
3. Then test on the flight pack.Setup and tuning
check the input voltage range covers your battery's full charge.
set 5 V for electronics or 6 V for servos with the jumper if available.
pick 3 A for small setups, more for many servos.
input from the battery, output to the receiver or servo rail.
keep the UBEC away from GPS and radio receivers.
What you need
Shop this list14 of 14 found in our store · ₹12,618
UBEC 5V 5A BEC Voltage Regulator: the part this guide coversUBEC 5V 5A BEC Voltage Regulator₹409
UBEC 5V/3A Switching Voltage Regulator: another version this guide coversUBEC 5V/3A Switching Voltage Regulator₹269
Mini UBEC DC-DC Step Down Converter 3A 5V: another version this guide coversMini UBEC DC-DC Step Down Converter 3A 5V₹272
2-13S 5V 5A BEC Voltage Regulator Module: another version this guide covers2-13S 5V 5A BEC Voltage Regulator Module₹769
2-6S 5V 5A BEC Voltage Regulator for Quadcopter Drones: another version this guide covers2-6S 5V 5A BEC Voltage Regulator for Quadcopter Drones₹959
UBEC-5V/7A 2-8S 7A DC-DC Voltage Regulator: another version this guide coversUBEC-5V/7A 2-8S 7A DC-DC Voltage Regulator₹519
ReadyToSky 2-6S 5V/12V 3A Switchable UBEC: another version this guide coversReadyToSky 2-6S 5V/12V 3A Switchable UBEC₹305
Bidirectional 20A UBEC 2-4S LiPo with 5V 2A Output: another version this guide coversBidirectional 20A UBEC 2-4S LiPo with 5V 2A Output₹775
Bluesky Mini 5V 3A FPV Gimbal PTZ UBEC: another version this guide coversBluesky Mini 5V 3A FPV Gimbal PTZ UBEC₹239
Crystal Ball UBEC V1 High-Efficiency DC-DC Converter: another version this guide coversCrystal Ball UBEC V1 High-Efficiency DC-DC Converter₹5,098
4S-6S 12V 3A UBEC: another version this guide covers4S-6S 12V 3A UBEC₹239
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
iMAX B6 balance charger: to charge the flight packiMAX B6 Balance Charger₹2,339
INA219 current and power monitor module: to check BEC load on the benchINA219 Current and Power Monitor Module₹249
Alternatives and when to choose them
Common mistakes to avoid
- Exceeding input voltage.
- Wrong output jumper.
- Mounting near GPS.
- Paralleling two UBECs.
Frequently asked questions
What does a UBEC do?
It provides a steady 5 or 6 V supply from a higher voltage battery.
Is a UBEC better than a linear BEC?
Yes, it wastes less power as heat, especially at higher voltages.
Can it power a Raspberry Pi?
Yes, if it gives 5 V at 3 A or more.
Why does my GPS lose lock near the UBEC?
Switching noise from the UBEC jams the GPS; move it away or shield it.
Can I use two UBECs together?
Do not connect two outputs in parallel without a diode setup.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
