Component guide · Intermediate · 3 min read
High-Current Servo UBECs (Hobbywing 25A, Henge 8A, Dual 8A+4A, 8A Adjustable)

Guide
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Big RC planes, robot arms and walking robots use many high-torque servos that draw large current peaks. Servo UBECs supply 5 to 8.4 V at 8 A to 25 A from 2S to 12S packs, keeping voltage steady when servos stall. Hobbywing and Henge units are popular; the dual 8A+4A module gives separate rails for servos and electronics.
Key specs at a glance
- Input
- 2S to 6S common (Hobbywing 25A up to 12S)
- Output
- 5.2, 6, 7.4 or 8.4 V selectable / adjustable
- Current
- 8 A to 25 A continuous (higher peaks)
- Dual module
- 8 A + 4 A outputs
- Type
- Switching
- Connectors
- Servo leads or thick output wires
This part can carry many amps. Use wire thick enough for the current, put a fuse close to the battery, check that connectors are rated for the load and give drivers and motors room to cool. A short at these currents melts wires in seconds.
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Hobbywing Servo UBEC 25A HV Voltage Regulator₹6,659
Option 2Henge 8A Switch-Mode UBEC Voltage Regulator₹817
Option 3Hobbywing 5V/6V 3A Switch-Mode Ultimate BEC₹367
Option 4UBEC-8A+4A High Efficiency Switch-Mode BEC Module₹1,260
Option 5Dual Channel UBEC 8A + 4A Voltage Regulator₹1,829
Option 68A 2-8S Lipo UBEC 6-36V Adjustable Output Regulator₹1,659
What the High-current servo UBEC is
A high-current servo UBEC is a switching regulator that gives 5 to 8.4 V at 5 to 20 A to power strong servos on large planes, helicopters, robots and arms.
Set the output to what your servos are rated for. HV servos accept 7.4 to 8.4 V for more speed and torque; standard servos stay at 5 to 6 V.
Feed the servo rail with thick wires in more than one place on large builds to avoid voltage drop.
High-current servo UBEC pinout
The pins on the High-current servo UBEC and what each one does.
| Pin | Function |
|---|---|
| Input | Pack |
| Output | Servo rail |
| Voltage select | Jumper or switch |
- Input
- Pack
- Output
- Servo rail
- Voltage select
- Jumper or switch
Wiring the High-current servo UBEC
Connect the High-current servo UBEC like this.
| High-current servo UBEC pin | RC plane | Robot arm |
|---|---|---|
| Input | 3S LiPo | 6S LiPo |
| Output | Servo rail of PCA9685 or receiver | Robot arm servo bus |
- Input
- RC plane:
- 3S LiPo
- Robot arm:
- 6S LiPo
- Output
- RC plane:
- Servo rail of PCA9685 or receiver
- Robot arm:
- Robot arm servo bus
Example code
A minimal sketch to check the part works.
1. Power from a current-limited supply or smoke stopper first.
2. Measure each output with a multimeter before connecting electronics.
3. Then test on the flight pack.Setup and tuning
set the output to match your servos, such as 6 V for standard and 7.4 or 8.4 V for HV servos.
add up the stall current of every servo that can move at once; pick a UBEC above that.
connect the UBEC input to the battery and the output to the receiver or servo board power rail.
remove the red wire from the ESC lead if the ESC also has a BEC, so two regulators do not fight.
add a large capacitor on the servo rail to absorb spikes.
What you need
Shop this list8 of 8 found in our store · ₹13,017
Hobbywing Servo UBEC 25A HV Voltage Regulator: the part this guide coversHobbywing Servo UBEC 25A HV Voltage Regulator₹6,659
Henge 8A Switch-Mode UBEC Voltage Regulator: another version this guide coversHenge 8A Switch-Mode UBEC Voltage Regulator₹817
Hobbywing 5V/6V 3A Switch-Mode Ultimate BEC: another version this guide coversHobbywing 5V/6V 3A Switch-Mode Ultimate BEC₹367
UBEC-8A+4A High Efficiency Switch-Mode BEC Module: another version this guide coversUBEC-8A+4A High Efficiency Switch-Mode BEC Module₹1,260
Dual Channel UBEC 8A + 4A Voltage Regulator: another version this guide coversDual Channel UBEC 8A + 4A Voltage Regulator₹1,829
8A 2-8S Lipo UBEC 6-36V Adjustable Output Regulator: another version this guide covers8A 2-8S Lipo UBEC 6-36V Adjustable Output Regulator₹1,659
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
INA219 current and power monitor module: to check BEC load on the benchINA219 Current and Power Monitor Module₹249
Alternatives and when to choose them
Common mistakes to avoid
- Setting HV voltage with standard servos.
- Running an ESC BEC and a UBEC in parallel.
- Sizing the UBEC on running current instead of stall current.
- Powering the computer and servos from one rail.
Frequently asked questions
How big a UBEC do I need for my servos?
Add the stall current of all servos that can load at once and pick a UBEC rated above that.
Can I use 8.4 V on standard servos?
No. Only HV servos accept 7.4 to 8.4 V; standard servos need 6 V or less.
Why remove the red wire from the ESC lead?
So the ESC BEC and the UBEC do not both drive the servo rail.
Why do servos reset my receiver?
Voltage drops under load; use a stronger UBEC and a capacitor on the rail.
Can a UBEC power a Raspberry Pi robot too?
Use a separate 5 V supply for the Pi so servo spikes do not reset it.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
