Buying guide · Intermediate · 3 min read
FC and ESC Stacks and AIO Boards
Choosing for Betaflight Drones
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
A stack pairs a flight controller board with a 4-in-1 ESC. An AIO combines both on one board for small drones. Match the mounting size (30.5 mm for 5 inch, 20 mm or 25.5 mm for smaller), the battery cell count and an ESC current rating a little above the motors' peak draw. Choose a modern MCU (F4, F7 or H7) and an ESC firmware you can update.
Key specs at a glance
- Mounting size
- 30.5 × 30.5 mm (M3), 25.5 × 25.5 mm, 20 × 20 mm (M2), 16 × 16 mm
- MCU
- F4 basic, F7 and H7 for more UARTs and speed
- Gyro
- ICM-42688, BMI270 or MPU6000 class
- ESC rating
- 35 to 65 A continuous for 5 inch; 12 to 25 A for whoops
- Battery
- 2S to 6S, check voltage rating
- ESC firmware
- BLHeli_S, BLHeli_32 or open AM32
This part can carry many amps. Use wire thick enough for the current, put a fuse close to the battery, check that connectors are rated for the load and give drivers and motors room to cool. A short at these currents melts wires in seconds.
Stack, AIO or separate
Pick by size and repairability.
| Option | Best for | Notes |
|---|---|---|
| FC + 4-in-1 ESC stack | 5 inch and larger | More power, easier to repair one board |
| AIO board | Whoops, cinewhoops, 3 inch | Light and simple; one failure takes out both |
| Separate FC and individual ESCs | Large and heavy-lift builds | Flexible but more wiring |
- FC + 4-in-1 ESC stack
- Best for:
- 5 inch and larger
- Notes:
- More power, easier to repair one board
- AIO board
- Best for:
- Whoops, cinewhoops, 3 inch
- Notes:
- Light and simple; one failure takes out both
- Separate FC and individual ESCs
- Best for:
- Large and heavy-lift builds
- Notes:
- Flexible but more wiring
Flight controller specs
F4 boards are enough for most freestyle. F7 and H7 add UARTs and extra features.
you need one each for the receiver, GPS, VTX control and perhaps a camera.
ICM-42688 and BMI270 are modern, low-noise parts.
an onboard OSD chip and flash memory for logs are very useful.
5 V and 9 V (or 12 V) for the receiver, camera and VTX.
ESC specs
The ESC current rating should be above the motor's maximum draw: for a typical 5 inch freestyle drone with 2306 motors on 6S, 45 to 60 A is common. Check the voltage rating for your battery. ESC firmware: BLHeli_S is simple, BLHeli_32 is more feature-rich but closed, AM32 is open source and growing. Use DShot (300 or 600) for a clean digital link; see ESC guide.
Build tips
- 1Solder the battery leads to the ESC pads with good joints and add a low-ESR capacitor near the power input.
- 2Use the supplied ribbon cable or wire harness between FC and ESC.
- 3Soft-mount the FC (dampers).
- 4Flash and configure Betaflight; set motor protocol and direction.
- 5Check props are off and motors spin in the right direction.
- 6
Try it: Lipo drone flight time calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Choosing a stack with a mounting size that does not fit the frame.
- ESC current rating too low for the motors.
- Forgetting the input capacitor, causing voltage spikes.
- Using a 4S ESC on a 6S battery.
- Not checking UART availability for GPS or VTX.
Frequently asked questions
Stack or AIO?
Stacks are easier to repair and handle more power. AIO boards save weight on small drones.
What does 4-in-1 ESC mean?
Four ESCs on one board, one for each motor.
BLHeli_32 or AM32?
AM32 is open and actively developed; BLHeli_32 is mature but closed.
How much current do I need?
Look at the motor's maximum current at your battery voltage and add 20 to 30 %.
Which MCU is best?
F405 is fine for most. F7 or H7 gives more UARTs and headroom.
Parts for this guide
Calculators
Terms in this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.




