How-to · Intermediate · 3 min read
Drone Dampers, Standoffs, Clamps and Landing Gear
Reducing Vibration and Protecting Parts
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Vibration from motors and props ruins gyro data and video. Fix it at the source first by balancing props and checking motors, then isolate the flight controller and camera with rubber grommets, gel dampers or an anti-vibration plate. Use nylon or aluminium standoffs of the right length, threadlock on screws, and shock-absorbing landing gear for heavy aircraft.
Key specs at a glance
- Dampers
- Rubber, silicone or gel mounts for flight controllers and camera plates
- Standoffs
- M3 nylon, aluminium or titanium spacers between stack boards
- Clamps and holders
- Metal or plastic clamps that grip tubes and parts
- Landing gear
- Fixed, shock-absorbing or retractable
- Hardware
- Stainless or alloy screws; nylon lock nuts
- Locking
- Threadlock on metal-to-metal bolts
Fix vibration at the source
Isolation helps, but it does not replace healthy motors. Check props for chips and balance them, replace bent motor shafts, tighten all motor screws with threadlock and make sure arms are not loose. Only then use dampers to remove what remains.
What each part is for
Choose the right part for the job.
| Part | Job | Notes |
|---|---|---|
| Rubber grommets | Soft-mount a flight controller (soft mounting) | Do not over-tighten; leave the board free to move slightly |
| Gel or silicone dampers | Isolate a camera or gimbal plate | Pick the right stiffness for the payload weight |
| Nylon standoffs | Space and insulate boards | Cheap; can flex on heavy stacks |
| Aluminium / titanium standoffs | Rigid spacing for large stacks | Use insulating washers where needed |
| Clamps and holders | Grip carbon tubes and accessories | Match tube diameter; see drone frame parts |
| Shock-absorbing landing gear | Protect payload on landing | Needed on heavy lift and camera drones |
- Rubber grommets
- Job:
- Soft-mount a flight controller (soft mounting)
- Notes:
- Do not over-tighten; leave the board free to move slightly
- Gel or silicone dampers
- Job:
- Isolate a camera or gimbal plate
- Notes:
- Pick the right stiffness for the payload weight
- Nylon standoffs
- Job:
- Space and insulate boards
- Notes:
- Cheap; can flex on heavy stacks
- Aluminium / titanium standoffs
- Job:
- Rigid spacing for large stacks
- Notes:
- Use insulating washers where needed
- Clamps and holders
- Job:
- Grip carbon tubes and accessories
- Notes:
- Match tube diameter; see drone frame parts
- Shock-absorbing landing gear
- Job:
- Protect payload on landing
- Notes:
- Needed on heavy lift and camera drones
Fitting tips
- 1Mount the flight controller with its arrow forward and the soft mount on all four holes.
- 2Keep wires slack near the flight controller so they do not transmit vibration.
- 3Use the correct screw length: too long screws can pierce the board or touch motor windings.
- 4Add threadlock to metal screws, and lock nuts or washers where plastic is used.
- 5After a crash, replace deformed standoffs and cracked dampers.
- 6Check the logs or video for jello or noise; see frames.
Camera and payload mounts
Gimbals and cameras need their own vibration isolation. Use dampers sized for the payload and mount the isolated plate on a rigid frame. Make sure the payload cannot swing into the props and add safety wires. For heavy equipment, see heavy-lift motors and the payload droppers overview.
Try it: Length converter calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Isolating a flight controller while the props are unbalanced.
- Over-tightening grommets so they do not damp.
- Using screws that are too long.
- Letting cables pull on a soft-mounted board.
- Skipping threadlock on motor mount screws.
Frequently asked questions
Do I need to soft mount a flight controller?
Many modern frames do not need it with good motors. If you see noise in gyro logs, a soft mount helps.
Nylon or metal standoffs?
Nylon is light and insulating; metal is stiffer for larger stacks.
What is jello in video?
Wobble caused by vibration. Balance props and dampen the camera mount.
Where do I use threadlock?
On metal screws that vibrate, such as motor and arm screws. Avoid it on plastic.
Do all drones need shock-absorbing landing gear?
No, but camera and heavy-lift drones benefit from it.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 20 step-by-step builds in our project library use parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.




