Raspberry Pi Pico weather display (MicroPython)
Your first MicroPython project: temperature and humidity on an OLED.
Shop by category
Shop all componentsAny of the three zones (PIR, door reed switch or window vibration sensor) sets off the alarm, and their states show on the console so you can see what tripped. The Mega has pins for many more zones, a keypad and a siren as the system grows.
Tick anything you already have and the total updates.
Passive infrared sensor that detects the body heat of moving people or animals up to about 7 m away.
Glass switch whose contacts close when a magnet is near.
Spring-type vibration switch with a comparator: the output goes high while it is being shaken.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Classic 16-character, 2-line LCD with an I²C backpack, so it needs only two signal wires.
Follow the colours: red is power, dark grey is ground, blue is a signal.
mega_security_console.inoVerify & upload in Electrolark// Three-zone security alarm on an Arduino Mega
// Geekobot project library · board: Arduino Mega 2560
// Wiring diagram, parts list and build steps: Geekobot project page "mega-security-console"
#include <Wire.h>
#include <LiquidCrystal_I2C.h>
// ---- pins ----
const uint8_t PIR_PIN = 22;
const uint8_t REED_PIN = 23;
const uint8_t VIB_PIN = 24;
const uint8_t BUZZER_PIN = 25;
const uint8_t LED_RED = 26;
LiquidCrystal_I2C lcd(0x27, 16, 2);
// ---- latest readings ----
bool motion = false;
bool doorOpen = false;
bool shake = false;
const unsigned long READ_EVERY_MS = 1000;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const unsigned long HOLD_MS = 10000; // stay on this long after the last trigger
unsigned long lastTrigger = 0;
const unsigned long WARMUP_MS = 30000UL; // sensor warm-up
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void setRedLed(bool on) { digitalWrite(LED_RED, on ? HIGH : LOW); }
void updateDisplay() {
lcd.setCursor(0, 0);
lcd.print(F("Motion "));
lcd.print(motion ? F("YES") : F("no"));
lcd.print(F(" "));
lcd.setCursor(0, 1);
lcd.print(F("Door "));
lcd.print(doorOpen ? F("YES") : F("no"));
lcd.print(F(" "));
lcd.print(statusText);
lcd.print(F(" "));
}
void evaluate() {
if (millis() < WARMUP_MS) { alertOn = false; statusText = "Warming up"; return; }
if ((motion || doorOpen || shake)) lastTrigger = millis();
alertOn = lastTrigger != 0 && millis() - lastTrigger < HOLD_MS;
statusText = alertOn ? "INTRUDER" : "OK";
}
void setup() {
Serial.begin(115200);
pinMode(PIR_PIN, INPUT);
pinMode(REED_PIN, INPUT_PULLUP);
pinMode(VIB_PIN, INPUT);
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
pinMode(LED_RED, OUTPUT);
lcd.init();
lcd.backlight();
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
motion = digitalRead(PIR_PIN) == HIGH;
doorOpen = digitalRead(REED_PIN) == HIGH;
shake = digitalRead(VIB_PIN) == HIGH;
evaluate();
Serial.print(F("Motion="));
Serial.print(motion ? F("yes") : F("no"));
Serial.print(F(", Door open="));
Serial.print(doorOpen ? F("yes") : F("no"));
Serial.print(F(", Vibration="));
Serial.print(shake ? F("yes") : F("no"));
Serial.print(F(", status=")); Serial.println(statusText);
updateDisplay();
}
setBuzzer(alertOn && (millis() / 250) % 2 == 0); // intermittent beep
setRedLed(alertOn && (millis() / 250) % 2 == 0);
}
The sketch above runs here on a simulated Arduino Mega. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Give it a minute to settle after power-up and keep it away from heaters, windows and fans.
Turn the sensitivity (Sx) pot clockwise and check the module has 5 V on VCC.
Bring the magnet within 1 cm and align it parallel to the glass body.
Low-triggered module: invert the logic in setBuzzer().
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Adjust the contrast pot on the backpack. If still blank, change 0x27 to 0x3F.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Use a 5 V USB phone charger or a power bank into the board's USB port.
10 parts: MEGA 2560 R3 Dev Board with ATmega2560 & CH340G, HC-SR501 PIR Motion Detector Sensor Module, Y213 Reed Switch Normally Open (glass), SW-420 Vibration Sensor Module – Digital Output, Active Buzzer Module 3.3–5V, Through-Hole LED Pack (Pack of 10), LCD1602 16x2 Character LCD (blue, with I2C adapter), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2–3 hours. The build on this page has 11 steps.
No. This page has the complete, tested code (mega_security_console.ino). Install this library first: LiquidCrystal I2C.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,347 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Character displays and I²C backpacks; Current-limiting resistors for LEDs; Debouncing noisy digital signals; Digital inputs and sensor hold time.
Ideas that reuse this build: PIR alarm and Keypad lock. They are listed under Take it further on this page.
Your first MicroPython project: temperature and humidity on an OLED.
A web page with ON and OFF buttons that switches a relay over Wi-Fi.
A warm ring light that fades up at dusk and down at dawn.
Turn a Pi and a touchscreen into a home command centre with a clock and to-do list.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Motion=no, Door open=yes, Vibration=yes, status=Warming up Motion=no, Door open=yes, Vibration=yes, status=Warming up
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.