Buying guide · Intermediate · 3 min read
Drone Frame Arms, Carbon Tubes, Motor Mounts and Canopies
Choosing Replacement Parts
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Multirotor frames are built from arms (carbon tubes or plates), motor mounts, folding or fixed arm clamps, a central plate and a canopy. Match tube diameter to the arm clamp, choose a tube thick enough for the motor and prop, and use folding mounts to make large drones portable. Replace damaged arms with the same size, never with a thinner one.
Key specs at a glance
- Tubes
- Round carbon fibre 16, 20, 25 or 30 mm are common on large frames
- Plates
- 3K carbon plates 2 to 5 mm thick for small and FPV frames
- Folding mounts
- Clamp a tube and fold the arm, with a locking ring
- Motor mounts
- Bolt-on discs or plates matched to the motor pattern
- Canopy
- Protects electronics, glass fibre or carbon
- Landing gear
- Fixed or retractable skids
Choosing arms
Large multirotors use round carbon tubes for light weight and torsional stiffness. The tube diameter must match the arm clamp, and the wall thickness sets stiffness. Thicker tubes carry bigger motors and props.
| Tube diameter | Typical use | Notes |
|---|---|---|
| 16 mm | 450 to 650 mm class, light payloads | Light, may flex under heavy motors |
| 20 to 25 mm | Mid to large frames | Common on Tarot and similar frames |
| 30 mm and above | Heavy-lift and agriculture | Needs matching clamps and mounts |
- 16 mm
- Typical use:
- 450 to 650 mm class, light payloads
- Notes:
- Light, may flex under heavy motors
- 20 to 25 mm
- Typical use:
- Mid to large frames
- Notes:
- Common on Tarot and similar frames
- 30 mm and above
- Typical use:
- Heavy-lift and agriculture
- Notes:
- Needs matching clamps and mounts
Folding mounts and clamps
Folding arm mounts let the arms swing back for transport. Look for a locking mechanism that clicks firmly, a clamp that grips the tube without crushing it, and waterproof sealing where wire passes through. Use a bit of threadlock on bolts, and check that the arm returns to the exact same position each time. See heavy-lift motors for motor choices.
Motor mounts and canopies
A motor mount must have the right bolt pattern for the motor and fit the tube diameter. Metal mounts with suspension reduce vibration. A canopy protects the electronics from rain and dust and may carry the GPS mast and antennas; vent it so the electronics do not overheat. Landing gear should be long enough to keep the props clear of the ground and any payload.
Repair tips
- 1Replace a cracked tube; do not glue or tape it.
- 2Match the tube diameter and length; keep all arms identical.
- 3Use new hardware and lock nuts after a crash.
- 4Balance the drone by moving the battery and equipment, not by shortening arms.
- 5Keep spare arms and mounts for field repairs; see FPV frames for small builds.
Try it: Length converter calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Replacing an arm with a thinner tube.
- Mixing tubes of different lengths.
- Over-tightening clamps and crushing the tube.
- Using damaged landing gear after a hard landing.
- Skipping threadlock on motor mount bolts.
Frequently asked questions
Carbon tube or aluminium tube?
Carbon is lighter and stiffer but breaks suddenly. Aluminium bends and is cheaper.
Do folding arms add flex?
A good folding mount adds little, but check the lock for play.
How do I measure tube size?
Measure the outside diameter with calipers.
Can I cut a carbon tube?
Yes, with a fine saw, wearing a mask and eye protection. The dust is harmful.
Do I need a canopy?
Highly recommended outdoors to protect electronics from dust and drizzle.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.




