Component guide · Intermediate · 3 min read
ESCs Explained
Current Ratings, Firmware and DShot
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
An ESC (electronic speed controller) switches a battery's power through a brushless motor's three wires in sequence, at a speed set by a throttle signal. Choose one rated for your battery's cell count and for more continuous current than your motor draws at full throttle, with 20 to 30% margin. Drones use 4-in-1 ESC boards with digital DShot signalling and open firmware such as Bluejay or AM32.
Key specs at a glance
- Rating
- Continuous amps per motor, plus short burst rating
- Voltage
- Cell count, for example 2S to 6S
- Signal
- PWM (1000 to 2000 µs), Oneshot, Multishot, DShot150/300/600
- Firmware
- BLHeli_S / Bluejay (8-bit), BLHeli_32 / AM32 (32-bit)
- Forms
- 4-in-1 board (stacks under the flight controller) or individual ESCs
- BEC
- Some ESCs include a 5 V regulator for the receiver or servos
This part can carry many amps. Use wire thick enough for the current, put a fuse close to the battery, check that connectors are rated for the load and give drivers and motors room to cool. A short at these currents melts wires in seconds.
What an ESC does
A brushless motor has three windings and no brushes, so something must switch current through them in the right order. The ESC uses six MOSFETs (three half-bridges) to energise two windings at a time, senses the back-EMF on the third to know where the rotor is, and moves to the next step. Throttle sets how much power each step gets. The result is a precise, efficient motor that can spin at tens of thousands of RPM.
Sizing an ESC
- 1Cell count: the ESC must be rated for your battery (for example 2S to 6S). Use a low-ESR capacitor across the battery pads; voltage spikes from the motors can kill ESCs, especially on 6S. A 35 V capacitor suits 4S; use 50 V for 6S.
- 2Current: find the motor's maximum current from its thrust table with your prop, then add 20 to 30% margin. 5 inch freestyle builds usually use 45 to 60 A 4-in-1 ESCs.
- 3Mounting: 4-in-1 boards come in 20x20, 25.5x25.5 and 30.5x30.5 mm patterns to match the flight controller stack.
- 4Cooling: ratings assume airflow from the props. On the bench, do not run motors at high throttle for long without props, and never test with props on indoors.
Signal protocols: PWM to DShot
| Protocol | Type | Notes |
|---|---|---|
| Standard PWM | Analog pulse 1000 to 2000 µs at 50 to 490 Hz | Planes, cars and Arduino projects; needs calibration |
| Oneshot125 / Oneshot42 / Multishot | Faster analog pulses | Older multirotor setups |
| DShot150 / 300 / 600 | Digital frames with checksum | No calibration, noise-immune; the default for drones |
| Bidirectional DShot | DShot plus RPM telemetry back to the flight controller | Enables RPM filtering for cleaner flight |
- Standard PWM
- Type:
- Analog pulse 1000 to 2000 µs at 50 to 490 Hz
- Notes:
- Planes, cars and Arduino projects; needs calibration
- Oneshot125 / Oneshot42 / Multishot
- Type:
- Faster analog pulses
- Notes:
- Older multirotor setups
- DShot150 / 300 / 600
- Type:
- Digital frames with checksum
- Notes:
- No calibration, noise-immune; the default for drones
- Bidirectional DShot
- Type:
- DShot plus RPM telemetry back to the flight controller
- Notes:
- Enables RPM filtering for cleaner flight
BLHeli_S, Bluejay, BLHeli_32 and AM32
BLHeli_S runs on 8-bit ESCs. Bluejay is an open-source replacement for BLHeli_S hardware that adds bidirectional DShot and higher PWM frequencies. BLHeli_32 ran on 32-bit ESCs; its developers stopped supporting it in 2024, so new 32-bit ESCs increasingly ship with AM32, an open-source alternative. All can be configured from a web or desktop configurator through the flight controller: motor direction, startup power, beeps and timing.
Driving an ESC from an Arduino
For a test rig, boat or fan, an ESC accepts a normal servo signal. Use the Servo library with microseconds, arm at minimum throttle, and keep props off while testing.
#include <Servo.h>
Servo esc;
void setup() {
esc.attach(9, 1000, 2000); // signal wire on D9, ground shared
esc.writeMicroseconds(1000); // minimum throttle to arm
delay(3000); // wait for the arming beeps
}
void loop() {
esc.writeMicroseconds(1150); // gentle spin: PROPS OFF while testing
}Try it: PWM duty cycle calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Running an ESC above its cell rating.
- Skipping the low-ESR capacitor on 5 and 6 inch builds.
- Bench-testing with props fitted.
- Sizing the ESC to the motor's average current instead of its peak with your prop.
- Forgetting to share ground between the Arduino and the ESC signal.
Frequently asked questions
What size ESC do I need?
One rated for your battery's cell count and at least 20 to 30% more continuous current than the motor's maximum draw with your prop, from the motor's thrust table.
What is DShot?
A digital protocol between flight controller and ESC. It sends throttle as numbers with a checksum, needs no calibration and resists noise. DShot300 and DShot600 are common.
Is AM32 better than BLHeli_32?
AM32 is open source and still developed, while BLHeli_32 is no longer supported. For new 32-bit ESCs, AM32 is the usual choice.
Can an Arduino control a brushless motor?
Yes, through an ESC. Send a servo-style signal of 1000 to 2000 µs with the Servo library, arm at 1000 µs, and share ground.
What is a BEC on an ESC?
A built-in voltage regulator that supplies 5 V for a receiver or servos. Many drone ESCs omit it because the flight controller has its own.
Parts for this guide
Calculators
Terms in this guide
Keep learning
Sources
- Bluejay and AM32 firmware project documentation
- Betaflight documentation on DShot and RPM filtering
- ESC manufacturer specifications
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.




