Component guide · Intermediate · 4 min read
Heavy-Lift and Pixhawk PDBs (Holybro, SwiftWing, Tarot, Axldrone, Vector, HUB-E)

Guide
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Heavy-lift PDBs distribute 60 A to 200 A from 6S to 14S packs to large ESCs on agricultural, mapping and delivery drones. Holybro and SwiftWing boards add XT30 or XT60 outputs and sometimes 5 V and 12 V bucks; Tarot and Axldrone boards handle very high currents; Vector Flightcore and HUB-E Power Cube combine distribution with regulated outputs.
Key specs at a glance
- Input
- 3S to 6S, up to 12S or 14S (board dependent)
- Current
- 60 A to 200 A
- Outputs
- Pads, XT30, XT60 or XT90
- Regulators
- 5 V and 12 V on some
- Mount
- Frame-specific or 30.5/45 mm
- Thickness
- Heavy copper layers
This part can carry many amps. Use wire thick enough for the current, put a fuse close to the battery, check that connectors are rated for the load and give drivers and motors room to cool. A short at these currents melts wires in seconds.
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Axldrone Power Distribution Board 200A₹24,923
Option 2Holybro PDB Board 60A/120A w/ Pre-Soldered XT60₹549
Option 3Holybro Power Distribution Board (PDB) with XT30 Pre-soldered₹1,259
Option 4SwiftWing PDB-02 Power Distribution Board XT60 6x XT30 3-6S₹999
Option 5SwiftWing PDB-14S Power Distribution Board w/ 12V & 5V Buck₹3,063
Option 6SwiftWing PDB-6S Power Distribution Board 3-6S w/ 5V 12V BEC₹1,900
What the Heavy-lift drone PDB is
A heavy-lift drone power distribution board (PDB) spreads high battery current to six or eight ESCs and often adds current sensing and regulated outputs for the autopilot and payload.
At these currents, connectors and solder joints are the weak points. Use XT90 or AS150 for the battery, and keep wires short and thick.
Arm and anti-spark connectors help on 12S and 14S, where connecting the pack makes a large spark.
Heavy-lift drone PDB pinout
The pins on the Heavy-lift drone PDB and what each one does.
| Pin | Function |
|---|---|
| Battery input | XT60/XT90 or pads |
| ESC outputs | Pads or plugs |
| Aux outputs | 5 V / 12 V (some) |
- Battery input
- XT60/XT90 or pads
- ESC outputs
- Pads or plugs
- Aux outputs
- 5 V / 12 V (some)
Wiring the Heavy-lift drone PDB
Connect the Heavy-lift drone PDB like this.
| Heavy-lift drone PDB pin | Agri / hex | Mapping quad |
|---|---|---|
| ESC outputs | 6 or 8 ESCs | 4 ESCs |
| Battery | 12S pack via anti-spark | 6S pack |
- ESC outputs
- Agri / hex:
- 6 or 8 ESCs
- Mapping quad:
- 4 ESCs
- Battery
- Agri / hex:
- 12S pack via anti-spark
- Mapping quad:
- 6S pack
Example code
A minimal sketch to check the part works.
1. Power from a current-limited supply or smoke stopper first.
2. Measure each output with a multimeter before connecting electronics.
3. Then test on the flight pack.Setup and tuning
choose a PDB rated above the total current of all motors at full throttle.
solder or bolt thick leads (8 to 10 AWG) and an anti-spark connector such as XT90-S or AS150.
keep each ESC lead the same length and as short as possible.
connect the current and voltage sense output to the autopilot power port and calibrate it.
power the autopilot from a dedicated power module, not from the payload rail.
first power-up through a smoke stopper or current-limited supply.
What you need
Shop this list14 of 15 found in our store · ₹82,680
Axldrone Power Distribution Board 200A: the part this guide coversAxldrone Power Distribution Board 200A₹24,923
Holybro PDB Board 60A/120A w/ Pre-Soldered XT60: another version this guide coversHolybro PDB Board 60A/120A w/ Pre-Soldered XT60₹549
Holybro Power Distribution Board (PDB) with XT30 Pre-soldered: another version this guide coversHolybro Power Distribution Board (PDB) with XT30 Pre-soldered₹1,259
SwiftWing PDB-02 Power Distribution Board XT60 6x XT30 3-6S: another version this guide coversSwiftWing PDB-02 Power Distribution Board XT60 6x XT30 3-6S₹999
SwiftWing PDB-14S Power Distribution Board w/ 12V & 5V Buck: another version this guide coversSwiftWing PDB-14S Power Distribution Board w/ 12V & 5V Buck₹3,063
SwiftWing PDB-6S Power Distribution Board 3-6S w/ 5V 12V BEC: another version this guide coversSwiftWing PDB-6S Power Distribution Board 3-6S w/ 5V 12V BEC₹1,900
SwiftWing PDB02 Direct Power Distribution Board 3-6S: another version this guide coversSwiftWing PDB02 Direct Power Distribution Board 3-6S₹375
SwiftWing PDB02-XT60 3S-6S Power Distribution Board: another version this guide coversSwiftWing PDB02-XT60 3S-6S Power Distribution Board₹450
SwiftWing PM03-14S Power Module & PDB (3S-14S, 120A): another version this guide coversSwiftWing PM03-14S Power Module & PDB (3S-14S, 120A)₹5,579
Tarot TL2996 12S High Current Power Distribution Board: another version this guide coversTarot TL2996 12S High Current Power Distribution Board₹3,479
Tarot TL60-10 Power Distribution Module 200A XT60: another version this guide coversTarot TL60-10 Power Distribution Module 200A XT60₹1,319- Vector Technics Technics Flightcore MK2 PDB (6S-14S): another version this guide coversFind this part
HUB-E HPC-3 Power Cube 4-14S w/ Dual 5.3V/12V Outputs: another version this guide coversHUB-E HPC-3 Power Cube 4-14S w/ Dual 5.3V/12V Outputs₹37,958
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
Digital watt meter and power analyser: to measure pack currentDigital Watt Meter and Power Analyser₹650
Alternatives and when to choose them
- FPV PDBs: small quads.
- Digital power modules.
- Heavy-lift drone motors.
Common mistakes to avoid
- Underrating the PDB current.
- Using thin wires on the battery input.
- Skipping the anti-spark connector on 12S packs.
- Powering the autopilot from a noisy payload rail.
Frequently asked questions
How much current must a heavy-lift PDB handle?
At least the sum of all motors' full-throttle current, plus margin, often 200 A or more.
Why use an anti-spark connector?
It stops the spark and connector damage when plugging in high-voltage packs.
Can the PDB power my camera and gimbal?
Yes, from a regulated output if its current rating covers them.
How do I calibrate the current sensor?
Compare the autopilot reading with a clamp meter and set the scale in the GCS.
Why do my ESCs reset when I punch the throttle?
Voltage dips from long or thin leads; shorten them and add low-ESR capacitors.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

