Component guide · Beginner · 3 min read
FPV and Multirotor PDBs with 5V/12V BEC (Matek PDB-XT60, CC3D PDB, Q250, F550)

Wiring
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
A power distribution board (PDB) splits the battery to four or more ESCs and usually adds 5 V and 12 V BEC outputs for the flight controller, camera and video transmitter. Matek PDB-XT60 and CC3D-style boards fit 250 mm racers, while the F550 board is part of the hexacopter frame. Many include an LC filter for cleaner video.
Key specs at a glance
- Input
- 2S to 4S or 3S to 6S (board dependent)
- ESC pads
- 4 or 6 pairs
- Current
- About 100 A total on most
- BEC
- 5 V and 12 V (on BEC versions)
- Filter
- LC filter on some
- Mount
- 30.5 mm or frame-specific
This part can carry many amps. Use wire thick enough for the current, put a fuse close to the battery, check that connectors are rated for the load and give drivers and motors room to cool. A short at these currents melts wires in seconds.
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Matek PDB-XT60 Power Distribution Board with 5V/12V BEC₹387
Option 2PDB-XT60 with 5V & 12V BEC Power Distribution Board₹909
Option 3CC3D NAZE32 F3 PDB w/ LC Filter & Dual 5V/12V BEC₹399
Option 4CC3D V2 PDB with Dual 5V/12V BEC, LC Filter & LED Switch₹348
Option 5CC3D Flight Controller Mini Power Distribution Board₹117
Option 6Q250 Power Distribution Board w/ 5V BEC₹208
What the FPV PDB with BEC is
An FPV power distribution board (PDB) with BEC splits battery power to the ESCs and gives regulated 5 V and 9 or 12 V for the flight controller, camera and VTX.
Solder with a hot, large-tip iron and plenty of flux; big pads need heat. Check for shorts between + and - with a meter before the first battery connection, then use a smoke stopper.
FPV PDB with BEC pinout
The pins on the FPV PDB with BEC and what each one does.
| Pin | Function |
|---|---|
| BAT + / - | Battery lead (XT60) |
| ESC pads | ESC power |
| 5V / 12V | BEC outputs |
| VBAT | Voltage to flight controller |
- BAT + / -
- Battery lead (XT60)
- ESC pads
- ESC power
- 5V / 12V
- BEC outputs
- VBAT
- Voltage to flight controller
Wiring the FPV PDB with BEC
Connect the FPV PDB with BEC like this.
| FPV PDB with BEC pin | Quad | Hex |
|---|---|---|
| ESC pads | 4 x ESC | 6 x ESC (F550) |
| 5V | Flight controller | Flight controller |
| 12V | VTX / camera | LED / gimbal |
- ESC pads
- Quad:
- 4 x ESC
- Hex:
- 6 x ESC (F550)
- 5V
- Quad:
- Flight controller
- Hex:
- Flight controller
- 12V
- Quad:
- VTX / camera
- Hex:
- LED / gimbal
Example code
A minimal sketch to check the part works.
1. Power from a current-limited supply or smoke stopper first.
2. Measure each output with a multimeter before connecting electronics.
3. Then test on the flight pack.Setup and tuning
solder the XT60 lead and a low-ESR capacitor to the main pads.
connect each ESC to its pad pair with correct polarity.
use 5 V for the flight controller and receiver, 9 or 12 V for HD video systems.
stay below the board's continuous current rating.
power up with a smoke stopper and check every voltage with a meter before connecting electronics.
What you need
Shop this list12 of 12 found in our store · ₹6,747
Matek PDB-XT60 Power Distribution Board with 5V/12V BEC: the part this guide coversMatek PDB-XT60 Power Distribution Board with 5V/12V BEC₹387
PDB-XT60 with 5V & 12V BEC Power Distribution Board: another version this guide coversPDB-XT60 with 5V & 12V BEC Power Distribution Board₹909
CC3D NAZE32 F3 PDB w/ LC Filter & Dual 5V/12V BEC: another version this guide coversCC3D NAZE32 F3 PDB w/ LC Filter & Dual 5V/12V BEC₹399
CC3D V2 PDB with Dual 5V/12V BEC, LC Filter & LED Switch: another version this guide coversCC3D V2 PDB with Dual 5V/12V BEC, LC Filter & LED Switch₹348
CC3D Flight Controller Mini Power Distribution Board: another version this guide coversCC3D Flight Controller Mini Power Distribution Board₹117
Q250 Power Distribution Board w/ 5V BEC: another version this guide coversQ250 Power Distribution Board w/ 5V BEC₹208
QAV-XS 222 FPV Racing Quadcopter PDB: another version this guide coversQAV-XS 222 FPV Racing Quadcopter PDB₹87
Generic PDB Soldered w/ XT60 & 3.5mm Bullet Connectors for 250mm FPV: another version this guide coversPDB Soldered w/ XT60 & 3.5mm Bullet Connectors for 250mm FPV₹447
Multirotor 100A ESC Power Distribution Board (PDB): another version this guide coversMultirotor 100A ESC Power Distribution Board (PDB)₹120
F550 / Q550 Hexacopter Frame PCB Power Distribution Board: another version this guide coversF550 / Q550 Hexacopter Frame PCB Power Distribution Board₹1,209
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
iMAX B6 balance charger: to charge the flight packiMAX B6 Balance Charger₹2,339
Alternatives and when to choose them
- FC and ESC stacks: 4-in-1 ESC replaces the PDB.
- Drone PDB and BEC.
- LC power filters.
Common mistakes to avoid
- Powering up for the first time without a smoke stopper.
- Overloading the 5 V BEC.
- Reversing ESC polarity on the pads.
- Skipping the battery capacitor.
Frequently asked questions
What is a PDB on an FPV drone?
A board that spreads battery power to the ESCs and powers the other electronics.
Do I still need a PDB with a 4-in-1 ESC?
Usually not, because the 4-in-1 already distributes power; a PDB helps with single ESCs.
How much current can the BEC supply?
Commonly 1 to 3 A on 5 V; check before adding LEDs or HD video.
Why should I use a smoke stopper?
It limits current on first power-up so a short does not destroy the board.
Can I power an HD video system from the PDB?
Yes, from the 9 V or 12 V BEC if it has enough current.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
