Component guide · Beginner · 3 min read
LC Power Filters for FPV Video Transmitters and Cameras (1A to 3A, 1S to 6S)

By Geekobot Learning Team · Updated 29 Oct 2026
On this page
An LC power filter is an inductor and capacitor in a small module that removes electrical noise from the power line before it reaches an FPV camera or video transmitter. Motors and ESCs create noise that shows as lines and rolling bars in analog video. Pick the filter by the current your VTX and camera draw and the battery cell count.
Key specs at a glance
- Current
- 1 A, 2 A or 3 A
- Input
- 1S to 4S or 1S to 6S
- Type
- LC low-pass
- Drop
- Small voltage drop
- Size
- Small, light
- Leads
- Pre-wired
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
What the FPV LC power filter is
An FPV LC power filter is a small inductor and capacitor board that cleans motor noise from the supply to the camera and video transmitter, removing lines and buzz from analog video.
Place the filter close to the VTX. If lines remain, check the ground path: camera and VTX should share one ground point.
FPV LC power filter pinout
The pins on the FPV LC power filter and what each one does.
| Pin | Function |
|---|---|
| IN + / - | From battery or BEC |
| OUT + / - | To VTX and camera |
- IN + / -
- From battery or BEC
- OUT + / -
- To VTX and camera
Wiring the FPV LC power filter
Connect the FPV LC power filter like this.
| FPV LC power filter pin | Direct battery | After BEC |
|---|---|---|
| IN | PDB VBAT | 12 V BEC |
| OUT | VTX and camera | Same |
- IN
- Direct battery:
- PDB VBAT
- After BEC:
- 12 V BEC
- OUT
- Direct battery:
- VTX and camera
- After BEC:
- Same
Example code
A minimal sketch to check the part works.
VTX 600 mW at 12 V ~ 0.6 A, camera ~ 0.15 A
Total ~ 0.75 A -> use a 1 A or 2 A filterSetup and tuning
wire the filter between the battery or BEC output and the camera and VTX supply only.
check the filter's current rating covers the camera and VTX together; do not run motors through it.
match the filter to the supply voltage; some are for 5 V, others for battery voltage.
keep the camera and VTX ground at the same point as the filter ground to avoid loops.
compare video with motors spinning (props off) before and after fitting.
What you need
Shop this list5 of 5 found in our store · ₹992
L-C Power Filter 2A 2-4S LiPo for FPV Transmitter: the part this guide coversL-C Power Filter 2A 2-4S LiPo for FPV Transmitter₹177
L-C Power Filter 3A 1-6S LiPo for FPV Transmitter: another version this guide coversL-C Power Filter 3A 1-6S LiPo for FPV Transmitter₹130
RTF LC Power Filter LC-FILTER 2A 2-4S Lipo for FPV & Immersion RC – Black: another version this guide coversRTF LC Power Filter LC-FILTER 2A 2-4S Lipo for FPV & Immersion RC – Black₹299
ReadyToSky L-C Power Filter 1A 1-4S LiPo for FPV Transmitter: another version this guide coversReadyToSky L-C Power Filter 1A 1-4S LiPo for FPV Transmitter₹209
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
Alternatives and when to choose them
Common mistakes to avoid
- Running motor current through the filter.
- Using a filter rated for a lower voltage than the battery.
- Creating a ground loop between camera and VTX.
- Skipping the low-ESR capacitor on the ESC, which is the main noise fix.
Frequently asked questions
What does an LC filter fix in FPV video?
It removes the lines and buzz in analog video caused by motor and ESC noise on the supply.
Can I power the motors through the LC filter?
No. It is only rated for the camera and VTX current; motors would burn it.
Do I need a filter with a modern flight controller?
Often not, because many have clean 5 V or 9 V regulators; add one if lines remain.
Where should I install the filter?
Between the power source and the camera and VTX supply, as close to them as practical.
Why is my video still noisy after the filter?
Check ground loops, the ESC capacitor and the antenna before blaming the filter.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
