Component guide · Beginner · 3 min read
Beitian BN-220, ReadyToSky BN-220 and BN-880, FlySky FS-CGPS01

RadioLink TS100, Naze32 and CC3D Mini GPS, SkyRC GSM020
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The Beitian BN-220 and BN-880 are low-cost GPS modules widely used on FPV drones and RC planes. The BN-220 is a tiny GPS only; the BN-880 adds an HMC5883 or QMC5883 compass. FlySky and RadioLink make similar modules for their own receivers and flight controllers, and the SkyRC GSM020 is a GNSS speed meter for RC cars and planes.
Key specs at a glance
- Chip
- u-blox M8030 class
- Systems
- GPS and GLONASS (BeiDou on some)
- Interface
- UART, default 9600 baud (BN-220/880)
- Compass
- BN-880 only (I2C)
- Supply
- 3 to 5.5 V
- Update rate
- 1 to 10 Hz
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Beitian BN-220 Dual GPS GLONASS Module TTL₹2,359
Option 2ReadyToSky BN-220 GPS Module₹1,364
Option 3ReadyToSky BN-880 GPS GLONASS Compass Module₹1,669
Option 4FlySky FS-CGPS01 Multi-GNSS GPS Module₹3,709
Option 5RadioLink TS100 V2.0 Mini GPS Module₹3,252
Option 6NZ Mini GPS Module for Naze32 Flight Controller₹1,040
What the BN-220, BN-880 and mini GPS modules is
The BN-220 and BN-880 are small GNSS modules for drones and robots; the BN-880 adds a compass for heading on autopilots.
BN modules use a small 4 or 6-wire cable. Colours vary between batches, so check the pin labels on the PCB instead of trusting colours.
They work with Arduino too: the output is standard NMEA sentences at 9600 baud.
BN-220, BN-880 and mini GPS modules pinout
The pins on the BN-220, BN-880 and mini GPS modules and what each one does.
| Pin | Function |
|---|---|
| VCC | Supply |
| GND | Ground |
| TX | GPS data out |
| RX | Commands in |
| SDA / SCL | Compass (BN-880) |
- VCC
- Supply
- GND
- Ground
- TX
- GPS data out
- RX
- Commands in
- SDA / SCL
- Compass (BN-880)
Wiring the BN-220, BN-880 and mini GPS modules
Connect the BN-220, BN-880 and mini GPS modules like this.
| BN-220, BN-880 and mini GPS modules pin | Arduino Uno | ESP32 |
|---|---|---|
| VCC | 5 V (or 3.3 V, check module) | 3V3 or 5 V (check module) |
| GND | GND | GND |
| TX | D4 (SoftwareSerial RX) | GPIO 16 (RX2) |
| RX | D3 (SoftwareSerial TX, via divider if 3.3 V) | GPIO 17 (TX2) |
- VCC
- Arduino Uno:
- 5 V (or 3.3 V, check module)
- ESP32:
- 3V3 or 5 V (check module)
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- TX
- Arduino Uno:
- D4 (SoftwareSerial RX)
- ESP32:
- GPIO 16 (RX2)
- RX
- Arduino Uno:
- D3 (SoftwareSerial TX, via divider if 3.3 V)
- ESP32:
- GPIO 17 (TX2)
Example code
A minimal sketch to check the part works.
// Read position from any NMEA GPS module (TinyGPSPlus library)
#include <TinyGPSPlus.h>
TinyGPSPlus gps;
void setup() {
Serial.begin(115200);
Serial2.begin(9600, SERIAL_8N1, 16, 17); // GPS TX -> GPIO 16. Many modules use 38400 or 115200
}
void loop() {
while (Serial2.available()) gps.encode(Serial2.read());
static unsigned long t = 0;
if (millis() - t > 1000) {
t = millis();
if (gps.location.isValid()) {
Serial.printf("%.6f, %.6f sats %d alt %.1f m\n", gps.location.lat(), gps.location.lng(),
gps.satellites.value(), gps.altitude.meters());
} else {
Serial.printf("Waiting for fix... chars %lu sats %d\n", gps.charsProcessed(), gps.satellites.value());
}
}
}Setup and tuning
most ship at 9600 or 38400 baud; match the flight controller or Arduino setting.
on the BN-880 connect SDA and SCL to the flight controller's I2C port and set the compass orientation.
mount on a mast away from the VTX, ESCs and power wires.
the ceramic patch must face the sky.
give it a few minutes outdoors with a clear sky view.
What you need
Shop this list11 of 12 found in our store · ₹20,518
Beitian BN-220 Dual GPS GLONASS Module TTL: the part this guide coversBeitian BN-220 Dual GPS GLONASS Module TTL₹2,359
ReadyToSky BN-220 GPS Module: another version this guide coversReadyToSky BN-220 GPS Module₹1,364
ReadyToSky BN-880 GPS GLONASS Compass Module: another version this guide coversReadyToSky BN-880 GPS GLONASS Compass Module₹1,669
FlySky FS-CGPS01 Multi-GNSS GPS Module: another version this guide coversFlySky FS-CGPS01 Multi-GNSS GPS Module₹3,709
RadioLink TS100 V2.0 Mini GPS Module: another version this guide coversRadioLink TS100 V2.0 Mini GPS Module₹3,252
NZ Mini GPS Module for Naze32 Flight Controller: another version this guide coversNZ Mini GPS Module for Naze32 Flight Controller₹1,040
MINI CC3D GPS Module: another version this guide coversMINI CC3D GPS Module₹999
SkyRC GSM020 GNSS Performance Analyzer Speed Meter: another version this guide coversSkyRC GSM020 GNSS Performance Analyzer Speed Meter₹5,099
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389- Uno R3 development board: the controller used in the wiring tableFind this part
0.96 inch OLED display 128x64: to show readings without a computer0.96" OLED Display 128x64₹139Closest match, check the specs
GY-NEO6MV2 GPS module (u-blox NEO-6M): the classic beginner GPS moduleGY-NEO6MV2 GPS Module w/ u-blox NEO-6M & Antenna₹499
Alternatives and when to choose them
- FPV M10 modules: newer chips.
- NEO-6M: classic Arduino module.
- NEO-M8N: bigger antenna, better fix.
Common mistakes to avoid
- Mounting the module near the VTX or power wires.
- Mounting it upside down with the patch facing the frame.
- Using a different baud rate from the module's setting.
- Skipping compass calibration after mounting.
Frequently asked questions
Does the BN-220 have a compass?
No. The BN-220 is GNSS only; the BN-880 includes a compass.
Why does my GPS take a long time to get a fix?
It needs a clear sky view. A backup battery or supercapacitor speeds up later fixes.
Can I use a BN-220 with an Arduino?
Yes. It sends NMEA sentences over UART, which TinyGPS++ reads.
Why is my drone's compass heading wrong?
Set the compass orientation correctly and mount it away from power wires and motors.
How many satellites do I need?
At least 6 to 8 for a reliable 3D fix; more is better for position hold.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

