Component guide · Intermediate · 4 min read
FPV GPS Modules

Foxeer M10Q, HGLRC M100 and M80, TBS M10 and M8.2, AxisFlying M10, SEQURE, SwiftWing and BotLab
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
These small GPS modules sit on FPV quads and wings for GPS rescue, position hold and on-screen speed and home arrow. Most use the u-blox M10 chip, which tracks four satellite systems at low power; the TBS M8.2 and Core Pro use the older M8. Many add a QMC5883 or IST8310 compass for INAV and ArduPilot. They connect to a spare UART and run from 5 V.
Key specs at a glance
- Chip
- u-blox M10 (most) or M8 / M9N
- Systems
- GPS, GLONASS, Galileo, BeiDou (M10 up to 4 at once)
- Update rate
- Up to 10 Hz (more with fewer systems)
- Interface
- UART (default 115200 or 38400), I2C for compass
- Supply
- 5 V
- Size
- About 15 to 25 mm square; 120/180/250 in the Foxeer name is the size option
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Foxeer M10Q 120 GPS Module w/ QMC5883 Compass₹2,429
Option 2Foxeer M10Q 180 GPS Module w/ QMC5883 Compass₹2,829
Option 3Foxeer M10Q 250 GPS Module with QMC5883 Compass₹2,729
Option 4HGLRC M100 MINI GPS Module₹1,749
Option 5HGLRC M100 PRO GPS Module₹2,038
Option 6HGLRC M80 GPS Module for FPV Drones₹2,069
What the FPV M10 GPS modules (Foxeer, HGLRC, TBS, AxisFlying) is
FPV M10 GPS modules use the u-blox M10 chip to give fast, accurate position to a flight controller for GPS rescue, position hold and speed on the OSD.
Betaflight uses GPS for GPS rescue (fly home on failsafe) and OSD data. INAV and ArduPilot use it for full navigation and need the compass too, except on fixed wings in INAV.
Mount it on top, away from the VTX antenna and power wires, with the ceramic patch facing the sky.
FPV M10 GPS modules (Foxeer, HGLRC, TBS, AxisFlying) pinout
The pins on the FPV M10 GPS modules (Foxeer, HGLRC, TBS, AxisFlying) and what each one does.
| Pin | Function |
|---|---|
| 5V | Supply |
| GND | Ground |
| TX | GPS data out |
| RX | Commands in |
| SDA / SCL | Compass (if fitted) |
- 5V
- Supply
- GND
- Ground
- TX
- GPS data out
- RX
- Commands in
- SDA / SCL
- Compass (if fitted)
Wiring the FPV M10 GPS modules (Foxeer, HGLRC, TBS, AxisFlying)
Connect the FPV M10 GPS modules (Foxeer, HGLRC, TBS, AxisFlying) like this.
| FPV M10 GPS modules (Foxeer, HGLRC, TBS, AxisFlying) pin | Flight controller (Pixhawk) | Flight controller (Betaflight / INAV) |
|---|---|---|
| 5V | Flight controller GPS port 5 V | Flight controller GPS port 5 V |
| GND | GND | GND |
| TX | FC UART RX | FC UART RX |
| RX | FC UART TX | FC UART TX |
| SDA / SCL | FC I2C (compass) | FC I2C (compass) |
- 5V
- Flight controller (Pixhawk):
- Flight controller GPS port 5 V
- Flight controller (Betaflight / INAV):
- Flight controller GPS port 5 V
- GND
- Flight controller (Pixhawk):
- GND
- Flight controller (Betaflight / INAV):
- GND
- TX
- Flight controller (Pixhawk):
- FC UART RX
- Flight controller (Betaflight / INAV):
- FC UART RX
- RX
- Flight controller (Pixhawk):
- FC UART TX
- Flight controller (Betaflight / INAV):
- FC UART TX
- SDA / SCL
- Flight controller (Pixhawk):
- FC I2C (compass)
- Flight controller (Betaflight / INAV):
- FC I2C (compass)
Example code
On the bench, the same modules also work with an ESP32 and TinyGPSPlus (see the NEO-7M guide).
ArduPilot (4.4 or later), GPS on SERIAL3 (GPS1 port):
SERIAL3_PROTOCOL = 5 GPS
GPS1_TYPE = 1 Auto (u-blox) [DroneCAN modules: GPS1_TYPE = 9, CAN_P1_DRIVER = 1]
COMPASS_ENABLE = 1 and run compass calibration in the ground station
PX4: GPS_1_CONFIG = GPS 1, then calibrate the compass.
Betaflight / INAV: enable GPS on the UART in Ports, protocol UBLOX, baud auto.Setup and tuning
GPS TX to a flight controller RX pad, RX to TX, 5 V and GND; the compass, if fitted, goes to SDA and SCL.
enable GPS on that UART, set the protocol to UBLOX and turn on auto-config.
mount on top of the drone with a clear sky view, away from the VTX antenna.
the first fix can take a few minutes outdoors; later fixes are faster.
set it only after you see 8 or more satellites and a home point.
What you need
Shop this list20 of 20 found in our store · ₹1,00,266
Foxeer M10Q 120 GPS Module w/ QMC5883 Compass: the part this guide coversFoxeer M10Q 120 GPS Module w/ QMC5883 Compass₹2,429
Foxeer M10Q 180 GPS Module w/ QMC5883 Compass: another version this guide coversFoxeer M10Q 180 GPS Module w/ QMC5883 Compass₹2,829
Foxeer M10Q 250 GPS Module with QMC5883 Compass: another version this guide coversFoxeer M10Q 250 GPS Module with QMC5883 Compass₹2,729
HGLRC M100 MINI GPS Module: another version this guide coversHGLRC M100 MINI GPS Module₹1,749
HGLRC M100 PRO GPS Module: another version this guide coversHGLRC M100 PRO GPS Module₹2,038
HGLRC M80 GPS Module for FPV Drones: another version this guide coversHGLRC M80 GPS Module for FPV Drones₹2,069
HGLRC M80 Pro GPS Module with QMC5883 Compass: another version this guide coversHGLRC M80 Pro GPS Module with QMC5883 Compass₹2,169
AxisFlying M10 GPS Module w/ Compass for FPV & Long Range: another version this guide coversAxisFlying M10 GPS Module w/ Compass for FPV & Long Range₹4,569
AxisFlying M80Q GPS Module with Compass: another version this guide coversAxisFlying M80Q GPS Module with Compass₹4,499
SEQURE M10-18 GPS Module: another version this guide coversSEQURE M10-18 GPS Module₹3,089
TBS M10 GPS GLONASS Module: another version this guide coversTBS M10 GPS GLONASS Module₹2,049
TBS M8.2 GPS Glonass Module: another version this guide coversTBS M8.2 GPS Glonass Module₹1,563
TBS Core Pro M8 GPS/Compass Module: another version this guide coversTBS Core Pro M8 GPS/Compass Module₹2,769
BotLab Dynamics BotNavigator V1 u-blox M10 GNSS Module: another version this guide coversBotLab Dynamics BotNavigator V1 u-blox M10 GNSS Module₹2,999
Crystal Ball GPS V1 u-blox NEO-M9N Multi-GNSS Module: another version this guide coversCrystal Ball GPS V1 u-blox NEO-M9N Multi-GNSS Module₹9,298
SwiftWing EDGE-M10 GNSS/Compass Module u-blox M10S: another version this guide coversSwiftWing EDGE-M10 GNSS/Compass Module u-blox M10S₹6,983
SwiftWing EDGE-M9N GNSS & Compass Module w/ Taoglas Antenna: another version this guide coversSwiftWing EDGE-M9N GNSS & Compass Module w/ Taoglas Antenna₹9,173
Holybro Pixhawk 6C flight controller: the autopilot these modules plug intoHolybro Pixhawk 6C Flight Controller + PM02 Power Module₹36,439Closest match, check the specs
u-blox NEO-M8N GPS module with ceramic antenna: a common multi-GNSS moduleu-blox NEO-M8N GPS Module w/ Ceramic Active Antenna₹739Closest match, check the specs
USB to TTL serial converter: to talk to the module from a PCUSB to TTL Serial Converter (CH340G / CP2102 / FT232RL / PL2303)₹85Closest match, check the specs
Alternatives and when to choose them
- BN-220 and BN-880: low-cost M8 modules.
- Pixhawk GPS modules: GH-connector modules for autopilots.
- NEO-M8N: the common M8N module.
Common mistakes to avoid
- Swapping TX and RX.
- Mounting the GPS under the VTX antenna.
- Testing indoors and expecting a fix.
- Enabling GPS rescue before checking satellites and home point.
Frequently asked questions
How many satellites do I need for GPS rescue?
Betaflight needs at least 8 by default before it allows arming with GPS rescue.
Why does my GPS never get a fix?
TX and RX may be swapped, the baud rate wrong, or the VTX is jamming it.
Is the M10 better than older M8 modules?
Yes. It uses less power and tracks four satellite systems at once.
Do I need the compass on the module?
Not for Betaflight GPS rescue; INAV and ArduPilot use it for position hold.
Why does the first fix take so long?
A cold start needs to download satellite data; keep it outside with sky view.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

