How-to · Beginner · 3 min read
Drone Navigation Lights, Strobes and Lost-Model Alarms
Orientation, Night Flying and Remote ID
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Navigation lights show a drone's orientation and position in low light: red on the left, green on the right and white at the back or front. Add a lost-model buzzer to find a crashed drone and, where the law requires it, a Remote ID module. Power lights from a 5 V or 12 V rail with the right current, keep wires tidy and make sure lights do not distract your camera.
Key specs at a glance
- Colours
- Red (left), green (right), white (rear/strobe)
- Supply
- 5 V or 12 V navigation LEDs; check each light
- Smart LEDs
- WS2812 modules with flight controller control
- Alarms
- 110 dB buzzers and lost-aircraft finders
- Remote ID
- Broadcast modules such as Holybro Remote ID
- Weight
- A few grams for most lights
Why add lights
Lights help you see the drone's direction at dusk, make it visible to others and make it easier to find after a crash. Some countries require lights or strobes for night flights, so check your local rules.
What is available
Choose by purpose.
| Part | Use | Notes |
|---|---|---|
| Red / green / white navigation LEDs (5-12 V) | Show orientation | Red on the left, green on the right |
| WS2812 LED module (BotGlow) | Controllable colours and patterns | Needs an LED pad on the flight controller |
| 110 dB buzzer with LEDs | Find a lost drone, low battery beep | Connects to the buzzer pads |
| Lost-model alarm | Standalone beeper from 4-6 V | Works on a separate battery |
| Remote ID module | Broadcast ID where required | Check local regulations |
- Red / green / white navigation LEDs (5-12 V)
- Use:
- Show orientation
- Notes:
- Red on the left, green on the right
- WS2812 LED module (BotGlow)
- Use:
- Controllable colours and patterns
- Notes:
- Needs an LED pad on the flight controller
- 110 dB buzzer with LEDs
- Use:
- Find a lost drone, low battery beep
- Notes:
- Connects to the buzzer pads
- Lost-model alarm
- Use:
- Standalone beeper from 4-6 V
- Notes:
- Works on a separate battery
- Remote ID module
- Use:
- Broadcast ID where required
- Notes:
- Check local regulations
Wiring
Connect lights to the correct voltage (5 V or 12 V) and ground. Navigation LEDs draw only tens of milliamps, but check the BEC can handle all loads; see PDB and BEC. WS2812 modules need 5 V, ground and a signal wire to the LED pad; configure the LED strip in Betaflight. A buzzer connects to the buzzer pads and works from the flight controller.
Placement
Mount lights where they are visible but not in the camera view. Put the green light on the right arm and red on the left. Use strong adhesive, heat-shrink or 3D-printed holders so they survive crashes. Use a white strobe at the back for visibility from afar.
Rules and Remote ID
Some regions require Remote ID so authorities can identify drones in flight. A module such as a Holybro Remote ID broadcasts identity and position. Rules differ by country, so check what applies where you fly. For other drone electronics see drone parts explained.
Try it: Led resistor calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Mixing up red and green sides.
- Overloading a small BEC with lights.
- Placing lights in front of the camera.
- Using 12 V lights on a 5 V rail.
- Ignoring local night-flying and Remote ID rules.
Frequently asked questions
Which side is red?
Red on the left, green on the right.
Do I need a lost-model alarm?
It is very helpful for finding a crashed drone.
Can I use WS2812 LEDs?
Yes. Set them up on the flight controller's LED pad.
Do lights affect flight time?
Slightly. Keep the draw low.
What is Remote ID?
A broadcast of the drone's identity and location where required.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 413 step-by-step builds in our project library use parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.






