Component guide · Intermediate · 4 min read
ExpressLRS Serial Receivers

RadioMaster RP1, RP2, RP3, RP4TD, Bandit BR1 and BR3 915MHz, XR4 and DBR4 Gemini Xrossband, GEPRC Gemini, HGLRC 2.4G and 915M, Jumper AION, SpeedyBee Nano, JHEMCU RX24T, IronLink, BotLink and Zerodrag Nexus1
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
ExpressLRS is an open-source radio link with very low latency and long range. These receivers output CRSF to a flight controller UART. 2.4GHz nano receivers like the RadioMaster RP1 and RP2 suit most quads; diversity models (RP3, RP4TD, IronLink) hold the link better in tricky spots; 915MHz Bandit receivers give extra range; Gemini Xrossband receivers (XR4, DBR4) use both bands at once.
Key specs at a glance
- Bands
- 2.4GHz, 915MHz, or both (Gemini Xrossband)
- Output
- CRSF serial, 420k baud
- Antenna
- Ceramic, T-type or dipole; diversity on RP3, RP4TD, IronLink
- Telemetry
- Yes, up to 100mW or more on some
- Supply
- 5V from the flight controller
- Firmware
- ExpressLRS 3.x, updated over Wi-Fi
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1BotLink Express LRS 2.4GHz Receiver V1₹2,188
Option 2EDITHFPV IronLink Rx-D ELRS (Antenna Diversity)₹2,587
Option 3GEPRC ELRS 915M/2.4G Gemini Xrossband Receiver₹5,879
Option 4HGLRC ELRS 2.4G Receiver₹1,581
Option 5HGLRC ELRS 915MHz Receiver for Long Range – Module with T-Type Antenna₹1,235
Option 6JHEMCU ExpressLRS RX24T 2.4G Receiver₹1,439
What the ExpressLRS (ELRS) serial receivers: RadioMaster RP and Bandit, Gemini dual-band and nano receivers is
ExpressLRS serial receivers are tiny long-range receivers that send all channels and telemetry to a flight controller over one CRSF serial link.
Pick a 2.4GHz nano receiver for freestyle and racing, a diversity receiver for long-range cinematic flights, and 915MHz (Bandit) or Gemini when range or punching through trees matters most. The transmitter module must be on the same band; a Gemini receiver needs a Gemini or dual-band radio to use both bands.
India uses 2.4GHz without a licence; check local rules before using 915MHz at high power. Keep antennas away from carbon and motor wires, with the tips pointing out of the frame.
ExpressLRS (ELRS) serial receivers: RadioMaster RP and Bandit, Gemini dual-band and nano receivers pinout
The pins on the ExpressLRS (ELRS) serial receivers: RadioMaster RP and Bandit, Gemini dual-band and nano receivers and what each one does.
| Pin | Function |
|---|---|
| 5V | Power from FC |
| GND | Ground |
| TX | To FC UART RX |
| RX | To FC UART TX |
| Antenna | U.FL or soldered |
- 5V
- Power from FC
- GND
- Ground
- TX
- To FC UART RX
- RX
- To FC UART TX
- Antenna
- U.FL or soldered
Wiring the ExpressLRS (ELRS) serial receivers: RadioMaster RP and Bandit, Gemini dual-band and nano receivers
TX goes to RX and RX to TX. Use a UART without inverters (avoid the old SBUS-only pad).
| ExpressLRS (ELRS) serial receivers: RadioMaster RP and Bandit, Gemini dual-band and nano receivers pin | Connection | Note |
|---|---|---|
| 5V | FC 5V pad | Not 3.3V |
| GND | FC GND | |
| Receiver TX | FC RX2 | Cross over |
| Receiver RX | FC TX2 | Cross over |
- 5V
- Connection:
- FC 5V pad
- Note:
- Not 3.3V
- GND
- Connection:
- FC GND
- Receiver TX
- Connection:
- FC RX2
- Note:
- Cross over
- Receiver RX
- Connection:
- FC TX2
- Note:
- Cross over
Example code
If the receiver will not bind, leave it powered for about 60 seconds without a link; it starts a Wi-Fi hotspot for updates.
1. Check the transmitter module and receiver run the same ELRS major version (for example 3.x).
2. Flash or configure the receiver with the ExpressLRS Configurator: pick the target, enter your binding phrase, flash over Wi-Fi or USB.
3. Wire the receiver: 5V, GND, RX pad to a flight controller TX pad, TX pad to the FC RX pad.
4. In Betaflight Ports, enable Serial Rx on that UART. In Receiver, choose CRSF.
5. Power up the radio first, then the drone. The receiver LED goes solid when linked.
6. Check stick movement in the Receiver tab and set channel map AETR.Setup and tuning
receiver TX to a flight controller RX pad, RX to TX, plus 5 V and GND.
enable Serial RX on that UART and set the receiver provider to CRSF.
use the same binding phrase on the transmitter and receiver.
keep the receiver and transmitter on the same ELRS major version.
mount the antenna away from carbon and motor wires, ideally in a T or vertical position.
What you need
Shop this list20 of 20 found in our store · ₹52,995
BotLink Express LRS 2.4GHz Receiver V1: the part this guide coversBotLink Express LRS 2.4GHz Receiver V1₹2,188
EDITHFPV IronLink Rx-D ELRS (Antenna Diversity): another version this guide coversEDITHFPV IronLink Rx-D ELRS (Antenna Diversity)₹2,587
GEPRC ELRS 915M/2.4G Gemini Xrossband Receiver: another version this guide coversGEPRC ELRS 915M/2.4G Gemini Xrossband Receiver₹5,879
HGLRC ELRS 2.4G Receiver: another version this guide coversHGLRC ELRS 2.4G Receiver₹1,581
HGLRC ELRS 915MHz Receiver for Long Range – Module with T-Type Antenna: another version this guide coversHGLRC ELRS 915MHz Receiver for Long Range – Module with T-Type Antenna₹1,235
JHEMCU ExpressLRS RX24T 2.4G Receiver: another version this guide coversJHEMCU ExpressLRS RX24T 2.4G Receiver₹1,439
Jumper AION-RX-MINI ELRS Receiver: another version this guide coversJumper AION-RX-MINI ELRS Receiver₹1,999
Jumper AION-RX-MINI-SE 2.4GHz ELRS Receiver: another version this guide coversJumper AION-RX-MINI-SE 2.4GHz ELRS Receiver₹1,399
RadioMaster Bandit BR1 ExpressLRS 915MHz Receiver: another version this guide coversRadioMaster Bandit BR1 ExpressLRS 915MHz Receiver₹3,153
RadioMaster Bandit BR3 ExpressLRS 915MHz Receiver: another version this guide coversRadioMaster Bandit BR3 ExpressLRS 915MHz Receiver₹3,881
RadioMaster DBR4 Dual Band Xross Gemini ExpressLRS Receiver: another version this guide coversRadioMaster DBR4 Dual Band Xross Gemini ExpressLRS Receiver₹4,199
RadioMaster RP1 ExpressLRS Nano Receiver: another version this guide coversRadioMaster RP1 ExpressLRS Nano Receiver₹2,500
RadioMaster RP1 V2 ExpressLRS Nano Receiver: another version this guide coversRadioMaster RP1 V2 ExpressLRS Nano Receiver₹2,635
RadioMaster RP2 V2 ExpressLRS 2.4GHz Nano Receiver: another version this guide coversRadioMaster RP2 V2 ExpressLRS 2.4GHz Nano Receiver₹2,599
RadioMaster RP3 V2 ExpressLRS 2.4GHz Nano Receiver: another version this guide coversRadioMaster RP3 V2 ExpressLRS 2.4GHz Nano Receiver₹3,163
RadioMaster RP4TD ExpressLRS 2.4GHz Diversity Receiver: another version this guide coversRadioMaster RP4TD ExpressLRS 2.4GHz Diversity Receiver₹4,257
RadioMaster XR4 Gemini Xrossband Dual-Band ExpressLRS Receiver: another version this guide coversRadioMaster XR4 Gemini Xrossband Dual-Band ExpressLRS Receiver₹4,364
SpeedyBee Nano 2.4G ExpressLRS ELRS Receiver: another version this guide coversSpeedyBee Nano 2.4G ExpressLRS ELRS Receiver₹1,069
SpeedyBee Nano 915M ExpressLRS ELRS Receiver: another version this guide coversSpeedyBee Nano 915M ExpressLRS ELRS Receiver₹1,069
Zerodrag Nexus1 Express LRS Receiver: another version this guide coversZerodrag Nexus1 Express LRS Receiver₹1,799
Alternatives and when to choose them
- RC receivers: ELRS and Crossfire: how protocols compare.
- ExpressLRS PWM receivers: for planes, cars and boats.
- FlySky receivers: AFHDS 2A radios.
Common mistakes to avoid
- Wiring TX to TX instead of TX to RX.
- Running mismatched ELRS major versions.
- Mounting the antenna against carbon fibre.
- Choosing SBUS instead of CRSF in Betaflight.
Frequently asked questions
Why does Betaflight show no receiver input?
TX and RX are swapped, or Serial RX and CRSF are not enabled on that UART.
How do I update the receiver firmware?
Use the ELRS Configurator over Wi-Fi or through the flight controller passthrough.
What is the binding phrase?
A word set in both firmwares so they pair automatically.
Which packet rate should I use?
Higher rates like 500 Hz suit racing; lower rates like 50 Hz give longer range.
Do ELRS receivers send telemetry?
Yes. Battery voltage, link quality and RSSI go back to the radio.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


