Component guide · Beginner · 4 min read
FlySky Receivers

FS-iA6, FS-iA6B, FS-iA10B, X6B, FS-A8S, FS-A6, FS-BS6, FS-R6B, FS-GR3E, FS2A, FS-RX2A Pro, Fuss RX2A and Mini 2.4GHz PPM/SBUS Receiver
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
FlySky receivers pair with FlySky radios such as the FS-i6 and FS-i6X. FS-iA6B and FS-iA10B give PWM servo outputs plus iBUS and PPM for flight controllers. X6B, FS-A8S and RX2A are small serial-only receivers for quads. FS-A6, FS-R6B and FS-GR3E use the older AFHDS protocol, so check that your radio supports it. Hold the bind plug in, power up and bind from the radio menu.
Key specs at a glance
- Protocols
- AFHDS 2A (iA6B, iA10B, X6B, A8S, RX2A), AFHDS (A6, R6B, GR3E, BS6)
- Channels
- 3 to 10
- Outputs
- PWM, PPM, iBUS, SBUS on A8S and RX2A
- Telemetry
- iBUS sensor port on iA6B, iA10B
- Supply
- 4-6.5V
- Range
- About 500m to 1km line of sight
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1FlySky FS-A6 2.4GHz 6-Channel Receiver₹125
Option 2FlySky FS-A8S 2.4G 8CH Mini Receiver Module Rev 2 – Black₹1,295
Option 3FlySky FS-BS6 6 Channel Receiver₹1,639
Option 4FlySky FS-GR3E 2.4GHz AFHDS 3CH Receiver₹769
Option 5FlySky FS-IA10B Radio Receiver – Black₹2,088
Option 6FlySky FS-R6B 2.4GHz 6CH Receiver₹1,309
What the FlySky AFHDS 2A receivers: FS-iA6B, FS-iA10B, X6B, FS-A8S and compatibles is
FlySky AFHDS receivers pair with FlySky radios over AFHDS 2A or AFHDS 3 and output PWM, PPM, iBUS or SBUS for planes, cars, boats and drones.
Use FS-iA6B or FS-iA10B for planes, cars and robots where servos plug straight in, or for a flight controller via iBUS. For a small quad, the X6B, FS-A8S or RX2A give iBUS or SBUS on one wire.
To bind: insert the bind lead in the B/VCC port (or press the bind button), power the receiver so the LED flashes fast, then hold the radio's bind key while turning it on. Remove the bind lead and set failsafe from the radio menu.
FlySky AFHDS 2A receivers: FS-iA6B, FS-iA10B, X6B, FS-A8S and compatibles pinout
The pins on the FlySky AFHDS 2A receivers: FS-iA6B, FS-iA10B, X6B, FS-A8S and compatibles and what each one does.
| Pin | Function |
|---|---|
| CH1-CH6 | PWM outputs (iA6B) |
| PPM / CH1 | PPM sum signal |
| iBUS servo | Serial to FC |
| SENS | iBUS telemetry sensors |
| B / VCC | Bind lead and power |
- CH1-CH6
- PWM outputs (iA6B)
- PPM / CH1
- PPM sum signal
- iBUS servo
- Serial to FC
- SENS
- iBUS telemetry sensors
- B / VCC
- Bind lead and power
Wiring the FlySky AFHDS 2A receivers: FS-iA6B, FS-iA10B, X6B, FS-A8S and compatibles
iBUS is not inverted, so any free UART RX works in Betaflight.
| FlySky AFHDS 2A receivers: FS-iA6B, FS-iA10B, X6B, FS-A8S and compatibles pin | Connection | Note |
|---|---|---|
| iBUS servo signal | FC UART RX | Set Serial Rx, IBUS |
| + / - | FC 5V / GND | |
| PWM servos | CH1-CH6 | Rail powered by ESC BEC |
- iBUS servo signal
- Connection:
- FC UART RX
- Note:
- Set Serial Rx, IBUS
- + / -
- Connection:
- FC 5V / GND
- PWM servos
- Connection:
- CH1-CH6
- Note:
- Rail powered by ESC BEC
Example code
Newer radios may need AFHDS 2A selected under System > RX setup > Mode.
1. Insert the bind lead into the B/VCC port.
2. Power the receiver; the LED blinks fast.
3. Hold BIND KEY on the FS-i6 and switch it on. The receiver LED goes slow, then solid.
4. Remove the bind lead, power-cycle both.
5. Menu > System > RX setup > Output mode: choose PWM+iBUS or PPM+SBUS.
6. Menu > Functions > Failsafe: set throttle low for each channel and save.Setup and tuning
AFHDS 2A receivers need an AFHDS 2A radio such as the FS-i6; AFHDS 3 needs a radio like the Noble or Paladin.
hold the bind button or fit the bind plug while powering up, then start bind on the radio.
use iBUS or SBUS on one wire for flight controllers; use PWM outputs for servos and ESCs.
set the failsafe in the radio menu, with throttle at zero or idle.
feed 4 to 6.5 V from the ESC BEC or a separate BEC.
What you need
Shop this list15 of 15 found in our store · ₹15,470
FlySky FS-A6 2.4GHz 6-Channel Receiver: the part this guide coversFlySky FS-A6 2.4GHz 6-Channel Receiver₹125
FlySky FS-A8S 2.4G 8CH Mini Receiver Module Rev 2 – Black: another version this guide coversFlySky FS-A8S 2.4G 8CH Mini Receiver Module Rev 2 – Black₹1,295
FlySky FS-BS6 6 Channel Receiver: another version this guide coversFlySky FS-BS6 6 Channel Receiver₹1,639
FlySky FS-GR3E 2.4GHz AFHDS 3CH Receiver: another version this guide coversFlySky FS-GR3E 2.4GHz AFHDS 3CH Receiver₹769
FlySky FS-IA10B Radio Receiver – Black: another version this guide coversFlySky FS-IA10B Radio Receiver – Black₹2,088
FlySky FS-R6B 2.4GHz 6CH Receiver: another version this guide coversFlySky FS-R6B 2.4GHz 6CH Receiver₹1,309
FlySky FS-RX2A Pro Radio Receiver – Black: another version this guide coversFlySky FS-RX2A Pro Radio Receiver – Black₹1,049
FlySky FS-iA6 6CH AFHDS 2A 2.4G Radio Receiver: another version this guide coversFlySky FS-iA6 6CH AFHDS 2A 2.4G Radio Receiver₹1,727
FlySky FS-iA6B RF 2.4GHz 6CH PPM/iBus Receiver: another version this guide coversFlySky FS-iA6B RF 2.4GHz 6CH PPM/iBus Receiver₹1,710
FlySky FS2A 4CH Receiver – Black: another version this guide coversFlySky FS2A 4CH Receiver – Black₹529
FlySky X6B 2.4G 6CH i-BUS PPM PWM Receiver for AFHDS 2A – Blue: another version this guide coversFlySky X6B 2.4G 6CH i-BUS PPM PWM Receiver for AFHDS 2A – Blue₹1,249
Fuss FS-RX2A Pro V1 Receiver Mini – IBUS / PPM / SBUS Signal: another version this guide coversFuss FS-RX2A Pro V1 Receiver Mini – IBUS / PPM / SBUS Signal₹715
Mini Radio Receiver 2.4GHz Compatible with FlySky PPM & SBUS Remote Control Transmitter: another version this guide coversMini Radio Receiver 2.4GHz Compatible with FlySky PPM & SBUS Remote Control Transmitter₹1,040
Dupont jumper wires: for the connectionsDupont Jumper Wires (40 pcs)₹49Closest match, check the specs
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
Alternatives and when to choose them
- FlySky and RadioLink radios: matching transmitters.
- ExpressLRS PWM receivers: longer range upgrade.
- FrSky and compatible receivers: other radios.
Common mistakes to avoid
- Buying a receiver with a different AFHDS version from the radio.
- Leaving the throttle failsafe unset.
- Feeding more than 6.5 V to the receiver.
- Using PWM wiring where the flight controller expects iBUS.
Frequently asked questions
How do I bind a FlySky receiver to my radio?
Power the receiver with the bind button held, then choose bind on the radio until the LED goes solid.
What is iBUS on FlySky receivers?
FlySky's serial protocol that sends all channels over one wire to a flight controller.
Will an AFHDS 2A receiver work with an AFHDS 3 radio?
Not in AFHDS 3 mode; some AFHDS 3 radios can also bind AFHDS 2A receivers in a compatibility mode.
How do I check the failsafe works?
With props off, set the failsafe, then switch off the radio and watch throttle drop.
Can I read iBUS with an Arduino?
Yes. Use an iBUS library on a hardware serial port to read every channel.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
