Component guide · Beginner · 4 min read
ExpressLRS PWM Receivers

RadioMaster ER3C-i, ER4, ER5A V2, ER5C V2, ER5C-i, ER6, ER6G, ER6GV, ER8, ER8G, ER8GV and WeAct Studio ELRS 6CH PWM/CRSF
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
ER series receivers bring ExpressLRS to models that use servos and ESCs directly: planes, gliders, cars, boats and robots. The number is the channel count (ER3C has 3, ER8 has 8). G models add a gyro for stabilised flight, V models measure battery voltage for telemetry, and i or C versions are compact for cars. WeAct's 6CH board does PWM or CRSF.
Key specs at a glance
- Channels
- 3 to 8 PWM outputs
- Band
- 2.4GHz ELRS
- Gyro
- ER6G, ER6GV, ER8G, ER8GV
- Voltage telemetry
- V models
- Supply
- 4-8.4V on the servo rail (from ESC BEC)
- Output mapping
- Any channel to any pin in the receiver web UI
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1RadioMaster ER3C-i 2.4GHz ELRS PWM Receiver₹2,536
Option 2RadioMaster ER4 2.4GHz ELRS PWM Receiver₹2,199
Option 3RadioMaster ER5A V2 2.4GHz ELRS PWM Receiver₹2,914
Option 4RadioMaster ER5C V2 2.4GHz ELRS PWM Receiver₹2,914
Option 5RadioMaster ER5C-i 2.4GHz ELRS PWM Receiver₹2,914
Option 6RadioMaster ER6 2.4GHz ELRS PWM Receiver₹3,679
What the ExpressLRS PWM receivers: RadioMaster ER3C to ER8GV and WeAct 6CH is
ExpressLRS PWM receivers output standard servo signals on several channels, so ELRS radio links can drive planes, cars and boats without a flight controller.
Plug servos and the ESC straight in; the ESC BEC powers the receiver through the servo rail. Use the ELRS web UI (Wi-Fi mode) or the radio's Lua script to set which channel drives which pin, the PWM frequency and failsafe positions.
Set failsafe for a car or boat to throttle neutral, and for a plane to low throttle with slight turn. Gyro models need the mounting direction set and a gain switch on your radio.
ExpressLRS PWM receivers: RadioMaster ER3C to ER8GV and WeAct 6CH pinout
The pins on the ExpressLRS PWM receivers: RadioMaster ER3C to ER8GV and WeAct 6CH and what each one does.
| Pin | Function |
|---|---|
| CH1-CH8 | Servo or ESC signal, + and - rail |
| Rail + | 4-8.4V from BEC |
| Rail - | Ground |
| VBAT (V models) | Battery voltage sense |
| Button | Bind or Wi-Fi mode |
- CH1-CH8
- Servo or ESC signal, + and - rail
- Rail +
- 4-8.4V from BEC
- Rail -
- Ground
- VBAT (V models)
- Battery voltage sense
- Button
- Bind or Wi-Fi mode
Wiring the ExpressLRS PWM receivers: RadioMaster ER3C to ER8GV and WeAct 6CH
Check the servo rail voltage the BEC supplies; high-voltage servos need an HV BEC.
| ExpressLRS PWM receivers: RadioMaster ER3C to ER8GV and WeAct 6CH pin | Connection | Note |
|---|---|---|
| ESC lead | CH3 | Throttle, powers the rail |
| Aileron servo | CH1 | |
| Elevator servo | CH2 | |
| Rudder or steering | CH4 |
- ESC lead
- Connection:
- CH3
- Note:
- Throttle, powers the rail
- Aileron servo
- Connection:
- CH1
- Elevator servo
- Connection:
- CH2
- Rudder or steering
- Connection:
- CH4
Example code
For PWM receivers skip the flight controller steps: map channels to outputs in the receiver's web UI instead.
1. Check the transmitter module and receiver run the same ELRS major version (for example 3.x).
2. Flash or configure the receiver with the ExpressLRS Configurator: pick the target, enter your binding phrase, flash over Wi-Fi or USB.
3. Wire the receiver: 5V, GND, RX pad to a flight controller TX pad, TX pad to the FC RX pad.
4. In Betaflight Ports, enable Serial Rx on that UART. In Receiver, choose CRSF.
5. Power up the radio first, then the drone. The receiver LED goes solid when linked.
6. Check stick movement in the Receiver tab and set channel map AETR.Setup and tuning
set the same binding phrase on the transmitter module and receiver, or use bind mode.
keep the receiver and transmitter on the same major ELRS version.
feed 5 V from an ESC BEC or separate BEC on the servo rail.
set which channel goes to each output in the receiver web UI.
set outputs to hold, no pulses or a set position for loss of signal.
What you need
Shop this list14 of 14 found in our store · ₹44,851
RadioMaster ER3C-i 2.4GHz ELRS PWM Receiver: the part this guide coversRadioMaster ER3C-i 2.4GHz ELRS PWM Receiver₹2,536
RadioMaster ER4 2.4GHz ELRS PWM Receiver: another version this guide coversRadioMaster ER4 2.4GHz ELRS PWM Receiver₹2,199
RadioMaster ER5A V2 2.4GHz ELRS PWM Receiver: another version this guide coversRadioMaster ER5A V2 2.4GHz ELRS PWM Receiver₹2,914
RadioMaster ER5C V2 2.4GHz ELRS PWM Receiver: another version this guide coversRadioMaster ER5C V2 2.4GHz ELRS PWM Receiver₹2,914
RadioMaster ER5C-i 2.4GHz ELRS PWM Receiver: another version this guide coversRadioMaster ER5C-i 2.4GHz ELRS PWM Receiver₹2,914
RadioMaster ER6 2.4GHz ELRS PWM Receiver: another version this guide coversRadioMaster ER6 2.4GHz ELRS PWM Receiver₹3,679
RadioMaster ER6G 2.4GHz ELRS PWM Receiver: another version this guide coversRadioMaster ER6G 2.4GHz ELRS PWM Receiver₹4,526
RadioMaster ER6GV 2.4GHz ELRS PWM Receiver: another version this guide coversRadioMaster ER6GV 2.4GHz ELRS PWM Receiver₹5,103
RadioMaster ER8 2.4GHz ELRS PWM Receiver: another version this guide coversRadioMaster ER8 2.4GHz ELRS PWM Receiver₹5,541
RadioMaster ER8G 2.4GHz ELRS PWM Receiver: another version this guide coversRadioMaster ER8G 2.4GHz ELRS PWM Receiver₹5,252
RadioMaster ER8GV 2.4GHz ELRS PWM Receiver: another version this guide coversRadioMaster ER8GV 2.4GHz ELRS PWM Receiver₹5,978
WeAct Studio ELRS 2.4G 6CH PWM/CRSF Receiver – Standard Set: another version this guide coversWeAct Studio ELRS 2.4G 6CH PWM/CRSF Receiver – Standard Set₹1,069
Dupont jumper wires: for the connectionsDupont Jumper Wires (40 pcs)₹49Closest match, check the specs
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
Alternatives and when to choose them
- ExpressLRS serial receivers: for flight controllers.
- FlySky receivers: budget PWM receivers.
- RC receivers: ELRS and Crossfire: protocol overview.
Common mistakes to avoid
- Mixing ELRS 2.x and 3.x firmware.
- Using a 900 MHz receiver with a 2.4 GHz transmitter.
- Leaving throttle failsafe on hold.
- Powering many servos from a weak BEC.
Frequently asked questions
How do I bind an ExpressLRS PWM receiver?
Use the same binding phrase on both ends, or put the receiver into bind mode.
Why does the receiver not connect to my radio?
The ELRS major versions or frequency bands do not match.
Can it power servos directly?
The servo rail passes BEC power; the receiver itself does not supply it.
How do I change the channel order?
Open the receiver Wi-Fi page and remap the outputs.
What does the failsafe do?
It sets what each output does when the link is lost, such as cutting throttle.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
