How-to · Intermediate · 3 min read
RC Receivers
ExpressLRS, Crossfire, FrSky and PWM Receivers Explained
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The receiver in your aircraft must match your transmitter's protocol. ExpressLRS and Crossfire receivers send all channels and telemetry over one serial wire (CRSF) to the flight controller; older receivers use SBUS or PWM. Wire power, ground and the UART, bind with the radio, set a failsafe and test range with the props off.
Key specs at a glance
- Protocols
- ELRS, TBS Crossfire/Tracer, FrSky ACCESS/ACCST, FlySky AFHDS
- Output
- CRSF (serial), SBUS, PPM or individual PWM pins
- Supply
- 5 V on most; some accept 2S directly
- Antennas
- T antenna, dipole or ceramic; keep them clear of carbon
- Telemetry
- Link quality, RSSI, battery and GPS back to the radio
- Diversity
- Dual antenna receivers reduce dropouts
Receiver types
Choose by link, size and output.
| Type | Strengths | Notes |
|---|---|---|
| ExpressLRS (2.4 GHz / 900 MHz) | Low latency, long range, low cost | Firmware version must match the radio |
| TBS Crossfire / Tracer | Proven long range link | More expensive |
| FrSky ACCESS / ACCST | Many receivers and sensors | Check the version compatibility |
| PWM receivers (FlySky, HotRC) | Direct servo outputs for planes and cars | No flight controller needed |
| Dual-band or diversity receivers | Better reliability on long flights | Larger and heavier |
- ExpressLRS (2.4 GHz / 900 MHz)
- Strengths:
- Low latency, long range, low cost
- Notes:
- Firmware version must match the radio
- TBS Crossfire / Tracer
- Strengths:
- Proven long range link
- Notes:
- More expensive
- FrSky ACCESS / ACCST
- Strengths:
- Many receivers and sensors
- Notes:
- Check the version compatibility
- PWM receivers (FlySky, HotRC)
- Strengths:
- Direct servo outputs for planes and cars
- Notes:
- No flight controller needed
- Dual-band or diversity receivers
- Strengths:
- Better reliability on long flights
- Notes:
- Larger and heavier
Wiring to a flight controller
Connect the receiver's 5 V and ground to the flight controller's 5 V and ground pads. For CRSF or SBUS, connect the receiver output to the flight controller's UART RX pad (and TX to TX for telemetry on CRSF). In Betaflight or ArduPilot, enable that UART as the receiver and choose the protocol. Do not use the same UART for other devices, and keep the antenna wires away from the video transmitter. See UART.
Binding and failsafe
- 1Put the receiver in bind mode (button, power cycles or a bind phrase for ELRS).
- 2Start the bind procedure on the transmitter and wait for the receiver's LED to go solid.
- 3Check that all channels move in the configurator.
- 4Set the failsafe so that, on link loss, the motors stop or the craft returns home.
- 5Do a range test: reduce power or use range test mode, with props removed.
Installation tips
- Mount antennas away from carbon fibre and the VTX, at right angles to each other for diversity.
- Cover exposed solder joints with heat-shrink.
- Update receiver firmware to match the transmitter module.
- Use a low-ESR capacitor near the receiver if the power is noisy.
- Keep a spare receiver and cable in your toolbox.
Try it: Link budget fspl calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Mixing ELRS firmware versions between radio and receiver.
- Mounting antennas against carbon plates.
- Forgetting to set the receiver protocol in the flight controller.
- Using the wrong UART or swapping TX and RX.
- Skipping failsafe configuration.
Frequently asked questions
Which receiver for a 5 inch freestyle drone?
A compact ExpressLRS receiver with a T antenna is popular and cheap.
What is CRSF?
A serial protocol carrying channels and telemetry on one wire.
Can I use a FrSky receiver with ELRS radio?
Not directly. The receiver must speak the transmitter's protocol.
How do I check range?
Use the radio's range check mode with props off and walk away until warnings appear.
Do I need telemetry?
It is useful for battery and link quality warnings, especially for long range flights.
Parts for this guide
Calculators
Terms in this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.




