Component guide · Beginner · 4 min read
Compact FPV Radios

Jumper T Pro V2, T-Lite V2, T14 and T20 Gemini, BetaFPV LiteRadio 2 SE, 3 and 3 Pro, TBS Mambo, HGLRC C1, Orqa FPV.Ctrl and DJI FPV Remote Controller 2 and 3
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
These are smaller or more specialised FPV radios. Jumper's T-Lite, T Pro, T14 and T20 run EdgeTX with ELRS like RadioMaster radios. BetaFPV LiteRadio 2 SE and 3 are cheap starter radios for tiny whoops and simulators. TBS Mambo uses Crossfire or Tracer modules. DJI FPV Remote Controller 2 and 3 only work with DJI drones and goggles.
Key specs at a glance
- Jumper
- EdgeTX, ELRS internal, hall gimbals on T14 and T20
- LiteRadio 2 SE / 3
- Fixed protocol (ELRS or FrSky), USB simulator mode
- LiteRadio 3 Pro
- EdgeTX, ELRS or CC2500, nano bay
- TBS Mambo
- FreedomTX/EdgeTX, Crossfire Nano module bay
- Orqa FPV.Ctrl
- Precision gimbals, ELRS
- DJI FPV RC2 / RC3
- DJI O3/O4 system only
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Jumper T Pro V2 Radio Controller ELRS₹14,178
Option 2Jumper T-lite V2 ELRS Radio Controller₹6,989
Option 3Jumper T14 Radio Controller with Standard Gimbals – ELRS₹13,560
Option 4Jumper T20 Gemini Radio Controller₹15,049
Option 5BetaFPV LiteRadio 2 SE Radio Transmitter (ELRS) – White₹5,709
Option 6BetaFPV LiteRadio 2 SE Radio Transmitter (FrSky) – White₹5,709
What the Compact FPV radios (Jumper, BetaFPV LiteRadio, TBS Mambo, HGLRC C1, Orqa, DJI FPV remotes) is
Compact FPV radios are small handheld transmitters, often with EdgeTX and a built-in ELRS module, made for whoops, freestyle quads and simulators.
For a first radio that will grow with you, choose an EdgeTX radio (Jumper T-Lite or T Pro, LiteRadio 3 Pro). LiteRadio 2 SE and LiteRadio 3 (non-Pro) are fine for simulators and tiny whoops but have fewer settings.
DJI remotes bind to DJI Avata, DJI FPV and O3/O4 air units and cannot fly ELRS or FrSky receivers.
Compact FPV radios (Jumper, BetaFPV LiteRadio, TBS Mambo, HGLRC C1, Orqa, DJI FPV remotes) pinout
The pins on the Compact FPV radios (Jumper, BetaFPV LiteRadio, TBS Mambo, HGLRC C1, Orqa, DJI FPV remotes) and what each one does.
| Pin | Function |
|---|---|
| Gimbals | Two sticks: throttle, yaw, pitch, roll |
| Switches and pots | Arm, flight modes, beeper, extra channels |
| Internal RF module | ELRS, 4-in-1 multiprotocol or CC2500 depending on version |
| External module bay | JR or nano bay on many radios |
| USB-C | Charging, EdgeTX updates, USB joystick for simulators |
- Gimbals
- Two sticks: throttle, yaw, pitch, roll
- Switches and pots
- Arm, flight modes, beeper, extra channels
- Internal RF module
- ELRS, 4-in-1 multiprotocol or CC2500 depending on version
- External module bay
- JR or nano bay on many radios
- USB-C
- Charging, EdgeTX updates, USB joystick for simulators
Wiring the Compact FPV radios (Jumper, BetaFPV LiteRadio, TBS Mambo, HGLRC C1, Orqa, DJI FPV remotes)
Always set up failsafe and test it with props off before the first flight. Keep the antenna fitted whenever RF is on.
| Compact FPV radios (Jumper, BetaFPV LiteRadio, TBS Mambo, HGLRC C1, Orqa, DJI FPV remotes) pin | Connection | Note |
|---|---|---|
| Battery | 2S Li-ion or LiPo as the radio specifies | Check polarity on the lead |
| Receiver | Bind from the radio's model menu | Same protocol both ends |
| Simulator | USB-C to PC, choose USB Joystick | No transmitting needed |
- Battery
- Connection:
- 2S Li-ion or LiPo as the radio specifies
- Note:
- Check polarity on the lead
- Receiver
- Connection:
- Bind from the radio's model menu
- Note:
- Same protocol both ends
- Simulator
- Connection:
- USB-C to PC, choose USB Joystick
- Note:
- No transmitting needed
Example code
These steps apply to the EdgeTX radios here. LiteRadio 2 SE and 3 use button combinations instead; DJI remotes bind from the goggles menu.
1. MODEL > new model, name it, set Internal RF to ExpressLRS (or your protocol).
2. Put the receiver in bind mode, then press [Bind] on the radio.
3. INPUTS and MIXES: keep AETR order (channel 1 roll, 2 pitch, 3 throttle, 4 yaw).
4. Add a switch on channel 5 for ARM (two-position switch, -100 / +100).
5. Add flight modes or beeper on channels 6 to 8.
6. In Betaflight: Receiver tab, check every stick moves the right bar.
7. Set failsafe: with props off, switch the radio off and check the motors stop.Setup and tuning
match the radio's internal module (ELRS, FrSky, CRSF) to your receiver.
set the same binding phrase on the radio and receivers, or use bind mode.
update EdgeTX and the ELRS module to versions that match your receivers.
run stick calibration in the radio settings before first use.
connect by USB in joystick mode to practise in FPV simulators.
What you need
Shop this list17 of 17 found in our store · ₹2,09,833
Jumper T Pro V2 Radio Controller ELRS: the part this guide coversJumper T Pro V2 Radio Controller ELRS₹14,178
Jumper T-lite V2 ELRS Radio Controller: another version this guide coversJumper T-lite V2 ELRS Radio Controller₹6,989
Jumper T14 Radio Controller with Standard Gimbals – ELRS: another version this guide coversJumper T14 Radio Controller with Standard Gimbals – ELRS₹13,560
Jumper T20 Gemini Radio Controller: another version this guide coversJumper T20 Gemini Radio Controller₹15,049
BetaFPV LiteRadio 2 SE Radio Transmitter (ELRS) – White: another version this guide coversBetaFPV LiteRadio 2 SE Radio Transmitter (ELRS) – White₹5,709
BetaFPV LiteRadio 2 SE Radio Transmitter (FrSky) – White: another version this guide coversBetaFPV LiteRadio 2 SE Radio Transmitter (FrSky) – White₹5,709
BetaFPV LiteRadio 3 Pro Radio Transmitter (CC2500): another version this guide coversBetaFPV LiteRadio 3 Pro Radio Transmitter (CC2500)₹6,869
BetaFPV LiteRadio 3 Pro Radio Transmitter (ELRS): another version this guide coversBetaFPV LiteRadio 3 Pro Radio Transmitter (ELRS)₹14,219
BetaFPV LiteRadio 3 Radio Transmitter (ELRS): another version this guide coversBetaFPV LiteRadio 3 Radio Transmitter (ELRS)₹6,779
BetaFPV LiteRadio 3 Radio Transmitter (FrSky) – 8-Channel, CC2500, 100mW, Built-in 2000mAh Battery: another version this guide coversBetaFPV LiteRadio 3 Radio Transmitter (FrSky) – 8-Channel, CC2500, 100mW, Built-in 2000mAh Battery₹6,779
TBS Mambo FPV RC Radio Drone Controller: another version this guide coversTBS Mambo FPV RC Radio Drone Controller₹17,689
HGLRC C1 Remote Control (RC + Strap + Dongle): another version this guide coversHGLRC C1 Remote Control (RC + Strap + Dongle)₹8,299
Orqa FPV.Ctrl Precision FPV Controller: another version this guide coversOrqa FPV.Ctrl Precision FPV Controller₹29,399
DJI FPV Remote Controller 2: another version this guide coversDJI FPV Remote Controller 2₹28,409
DJI FPV Remote Controller 3: another version this guide coversDJI FPV Remote Controller 3₹27,699
ExpressLRS receiver: to bind with an ELRS radioJHEMCU ExpressLRS RX24T 2.4G Receiver₹1,439Closest match, check the specs
USB-C cable: for charging, firmware updates and simulator useArduino USB-C to USB-C Cable w/ USB-A Adapter₹1,059Closest match, check the specs
Alternatives and when to choose them
- RadioMaster radios: the main EdgeTX range.
- Choosing an RC transmitter: buying guide.
- FPV goggles: the other half of FPV.
Common mistakes to avoid
- Mixing ELRS major versions on radio and receiver.
- Skipping stick calibration.
- Buying a fixed-protocol radio that does not match your receivers.
- Flying without setting a failsafe.
Frequently asked questions
Which compact radio is good for beginners?
A radio with EdgeTX and ELRS, such as the Jumper T-Lite or BetaFPV LiteRadio 3 Pro, offers the most flexibility.
Can I use the radio with a simulator?
Yes. Plug it in over USB and choose joystick mode.
What is a binding phrase?
It is a shared phrase in ELRS that links the radio and receiver without pressing bind buttons.
Why will my receiver not bind?
Check that both use the same protocol, ELRS version and binding phrase.
Do I need an external module?
Not if the internal module matches your receivers; a module bay adds other protocols.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


