How-to · Beginner · 3 min read
XT30, XT60 and Drone Connectors
Power Plugs, JST Cables and Race Wire
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Use XT30 for small drones, XT60 for most 5 inch and up, and larger connectors such as AS150 for heavy lift. Match the connector to the current and keep polarity the same on the battery, ESC and charger. Flight controllers use small JST-SH, JST-GH and DF13 connectors, so buy cables with the right pin count. Use silicone race wire sized for the current.
Key specs at a glance
- XT30
- About 30 A class, small drones
- XT60
- About 60 A class, common for 4S-6S
- AS150 / anti-spark
- Heavy lift and agri drones
- Flight controller
- JST-SH, JST-GH, DF13, Clik-Mate cables
- DroneCAN
- JST-GH 4-pin cables
- Wire
- Silicone race wire, thick for motors and battery leads
Power connectors
Choose by the current your drone draws.
| Connector | Typical use | Notes |
|---|---|---|
| XT30 | Tiny whoops, 3 inch drones, 2S-4S | Light and small |
| XT60 | 5 inch freestyle and racing, 4S-6S | Most common |
| XT90 / AS150 | Long range, heavy lift | Anti-spark types avoid arcing on connection |
| XT60 PCB mounts | Soldered onto boards | Avoid stress on the board |
- XT30
- Typical use:
- Tiny whoops, 3 inch drones, 2S-4S
- Notes:
- Light and small
- XT60
- Typical use:
- 5 inch freestyle and racing, 4S-6S
- Notes:
- Most common
- XT90 / AS150
- Typical use:
- Long range, heavy lift
- Notes:
- Anti-spark types avoid arcing on connection
- XT60 PCB mounts
- Typical use:
- Soldered onto boards
- Notes:
- Avoid stress on the board
Polarity and soldering
Always check red is positive on every part before connecting a battery. Tin the wire and the cup, hold the wire straight and heat until the solder flows, then add heat-shrink. Cold joints get hot at high current; see soldering and connectors. Use a smoke stopper for first power-up.
Flight controller connectors
Flight controller ports use small locking connectors: JST-SH (1.0 mm) on many boards, JST-GH (1.25 mm) on Pixhawk-style controllers, DF13 on older ones and Clik-Mate on Cube. Buy cables with the right pin count and check the pinout; pin order is not standard between brands. DroneCAN uses a JST-GH 4-pin cable; see Pixhawk and ArduPilot.
Wire gauge
Thicker wire carries more current with less heat. Use the wire gauge tool and voltage drop tool to size battery leads and motor wires. Silicone-insulated race wire is flexible and heat resistant. Protect motor wires with tubes where they rub, as in dampers and standoffs.
Tips
- Keep spare connectors and a crimp or solder kit in your field bag.
- Replace worn XT plugs that heat up or feel loose.
- Use strain relief so the wire does not break at the solder joint.
- Label cables so you can reconnect them correctly.
Try it: Wire gauge calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Reversing polarity between battery and ESC.
- Using XT30 on a high-current build.
- Cold-soldering large connectors.
- Buying FC cables with the wrong pin order.
- Leaving wires with no strain relief.
Frequently asked questions
XT30 or XT60?
XT30 for small low-current drones, XT60 for most larger ones.
What is an anti-spark connector?
A connector with a resistor that limits arcing when you plug in a large battery.
Are all JST connectors the same?
No. SH and GH have different pitch.
What wire gauge for battery leads?
Typically 12 to 14 AWG for 5 inch drones; check the current.
Why do my connectors get hot?
A loose fit, cold joint or too-small connector.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.






