Component guide · Intermediate · 4 min read
BMP390 and BMP581 Pressure Sensors

Altitude, Wiring and Code
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The Bosch BMP390 and BMP581 are high-precision barometric pressure sensors that resolve altitude changes of about 10 to 25 cm, several times better than the BMP280. They read 300 to 1250 hPa over I2C or SPI and include temperature. The BMP581 has lower noise and power; the BMP585 is a waterproof-port version. Use them for drones, altimeters, floor detection and weather stations.
Key specs at a glance
- Range
- 300 to 1250 hPa
- Noise
- About 0.03 hPa (BMP390), 0.01 hPa (BMP581) RMS
- Altitude resolution
- About 25 cm (BMP390), 10 cm (BMP581)
- Interface
- I2C (0x76/0x77 for BMP390, 0x46/0x47 for BMP581) or SPI
- Supply
- 1.7 to 3.6 V (breakouts 3.3 to 5 V)
- Extras
- Temperature, FIFO, interrupt pin
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Adafruit BMP390 Precision Barometric Pressure and Altimeter Module – I2C/SPI, STEMMA QT₹1,709
Option 2Waveshare BMP390 High-Precision Barometric Pressure Sensor – I2C/SPI Interface₹2,179
Option 3DFRobot Fermion BMP390L Digital Barometric Pressure Sensor (Breakout) – I2C/SPI Interface₹1,569
Option 4Bosch BMP380 Barometric Pressure Sensor, 300-1250 hPa, Low Noise, I2C/SPI, LGA Package₹259
Option 5Adafruit BMP581 I2C/SPI Barometric Pressure & Temperature Sensor – STEMMA QT Breakout₹1,719
Option 6DFRobot Fermion BMP581 High-Precision Barometric Pressure Sensor Module – I2C/SPI₹899
What the BMP390 / BMP581 sensor is
Air pressure drops about 12 Pa per metre of height near sea level. These sensors measure it finely enough to see you lift the board from a desk to a shelf.
Absolute altitude needs today's sea-level pressure from a weather report; relative altitude (height above the starting point) needs only a reading at start-up. The BMP581 is a different design from the BMP390, with a different address and library.
BMP390 / BMP581 sensor pinout
The pins on the BMP390 / BMP581 sensor and what each one does.
| Pin | Function |
|---|---|
| VIN / VCC | Supply (3.3 or 5 V on breakouts) |
| GND | Ground |
| SCK / SCL | SPI clock or I2C clock |
| SDI / SDA | SPI data in or I2C data |
| SDO | SPI data out, or I2C address select |
| CS | SPI chip select (leave high for I2C) |
| INT | Interrupt output (optional) |
- VIN / VCC
- Supply (3.3 or 5 V on breakouts)
- GND
- Ground
- SCK / SCL
- SPI clock or I2C clock
- SDI / SDA
- SPI data in or I2C data
- SDO
- SPI data out, or I2C address select
- CS
- SPI chip select (leave high for I2C)
- INT
- Interrupt output (optional)
Wiring the BMP390 / BMP581 sensor
Most breakouts have pull-up resistors and a regulator, so they run from 3.3 V or 5 V. Bare sensor ICs are 3.3 V (or 1.8 V) only: solder them to a breakout first and use a level shifter with 5 V boards. For SPI, use SCK, SDI, SDO and CS as for any SPI device.
| BMP390 / BMP581 sensor pin | Arduino Uno | ESP32 |
|---|---|---|
| VCC | 5V (or 3.3V) | 3V3 |
| GND | GND | GND |
| SDA | A4 | GPIO 21 |
| SCL | A5 | GPIO 22 |
- VCC
- Arduino Uno:
- 5V (or 3.3V)
- ESP32:
- 3V3
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- SDA
- Arduino Uno:
- A4
- ESP32:
- GPIO 21
- SCL
- Arduino Uno:
- A5
- ESP32:
- GPIO 22
Example code
For the BMP581 use the SparkFun BMP581 or Adafruit BMP5xx library; the altitude maths is the same.
#include <Adafruit_BMP3XX.h>
Adafruit_BMP3XX bmp;
float startHpa;
void setup() {
Serial.begin(115200);
if (!bmp.begin_I2C()) { Serial.println("BMP390 not found"); while (1); }
bmp.setPressureOversampling(BMP3_OVERSAMPLING_8X);
bmp.setIIRFilterCoeff(BMP3_IIR_FILTER_COEFF_3);
bmp.performReading();
startHpa = bmp.pressure / 100.0;
}
void loop() {
bmp.performReading();
float hpa = bmp.pressure / 100.0;
float metres = 44330.0 * (1.0 - pow(hpa / startHpa, 0.1903));
Serial.printf("%.2f hPa %.2f m above start\n", hpa, metres);
delay(200);
}Setup and tuning
more oversampling and a stronger filter give smoother altitude but slower response.
cover the sensor with a little foam so air movement does not look like altitude changes.
shade it; heating the board changes the readings.
set the local sea-level pressure (QNH) from a weather service.
What you need
Shop this list15 of 16 found in our store · ₹17,720
Adafruit BMP390 Precision Barometric Pressure and Altimeter Module – I2C/SPI, STEMMA QT: the part this guide coversAdafruit BMP390 Precision Barometric Pressure and Altimeter Module – I2C/SPI, STEMMA QT₹1,709
Waveshare BMP390 High-Precision Barometric Pressure Sensor – I2C/SPI Interface: another version this guide coversWaveshare BMP390 High-Precision Barometric Pressure Sensor – I2C/SPI Interface₹2,179
DFRobot Fermion BMP390L Digital Barometric Pressure Sensor (Breakout) – I2C/SPI Interface: another version this guide coversDFRobot Fermion BMP390L Digital Barometric Pressure Sensor (Breakout) – I2C/SPI Interface₹1,569
Bosch BMP380 Barometric Pressure Sensor, 300-1250 hPa, Low Noise, I2C/SPI, LGA Package: another version this guide coversBosch BMP380 Barometric Pressure Sensor, 300-1250 hPa, Low Noise, I2C/SPI, LGA Package₹259
Adafruit BMP581 I2C/SPI Barometric Pressure & Temperature Sensor – STEMMA QT Breakout: another version this guide coversAdafruit BMP581 I2C/SPI Barometric Pressure & Temperature Sensor – STEMMA QT Breakout₹1,719
DFRobot Fermion BMP581 High-Precision Barometric Pressure Sensor Module – I2C/SPI: another version this guide coversDFRobot Fermion BMP581 High-Precision Barometric Pressure Sensor Module – I2C/SPI₹899
DFRobot Gravity BMP581 Barometric Pressure Sensor (±0.3hPa High Accuracy, I2C/UART): another version this guide coversDFRobot Gravity BMP581 Barometric Pressure Sensor (±0.3hPa High Accuracy, I2C/UART)₹994
SparkFun BMP581 Pressure Sensor (Qwiic) – I2C/SPI, 30-125kPa, ±0.5hPa Accuracy: another version this guide coversSparkFun BMP581 Pressure Sensor (Qwiic) – I2C/SPI, 30-125kPa, ±0.5hPa Accuracy₹2,599
Bosch BMP581 Pressure Sensor, 300~1250 hPa, Ultra-Low Noise, I²C/SPI Interface: another version this guide coversBosch BMP581 Pressure Sensor, 300~1250 hPa, Ultra-Low Noise, I²C/SPI Interface₹419
Adafruit BMP585 Ported I2C / SPI Temperature and Pressure Sensor – STEMMA QT: another version this guide coversAdafruit BMP585 Ported I2C / SPI Temperature and Pressure Sensor – STEMMA QT₹2,307
DFRobot Fermion BMP585 High-Precision Barometric Pressure and Temperature Sensor (±0.3 hPa) – I2C/SPI/I3C Module: another version this guide coversDFRobot Fermion BMP585 High-Precision Barometric Pressure and Temperature Sensor (±0.3 hPa) – I2C/SPI/I3C Module₹1,049
DFRobot Gravity BMP585 High-Precision Barometric Pressure and Temperature Sensor (I2C/UART): another version this guide coversDFRobot Gravity BMP585 High-Precision Barometric Pressure and Temperature Sensor (I2C/UART)₹1,441
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389- Uno R3 development board: the controller used in the wiring tableFind this part
0.96 inch OLED display 128x64: to show readings without a computer0.96" OLED Display 128x64₹139Closest match, check the specs
Dupont jumper wires: for the connectionsDupont Jumper Wires (40 pcs)₹49Closest match, check the specs
Alternatives and when to choose them
- BME280 / BMP280: cheaper, about 1 m altitude resolution, BME280 adds humidity.
- Barometric pressure sensors: MS5611 and other precision options.
- BMP180: the older Bosch sensor.
Try it: I2c pullup calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Using BMP280 code with a BMP581, which needs its own library.
- Leaving the sensor in a draught or sunlight.
- Expecting absolute altitude without setting sea-level pressure.
- Using no oversampling or filtering, so readings jump.
Frequently asked questions
BMP390 or BMP581?
BMP581 for the lowest noise and power; BMP390 for wide library support.
How accurate is altitude?
Relative changes of 10 to 25 cm; absolute altitude depends on the weather pressure you set.
What is the I2C address?
0x77 or 0x76 for the BMP390; 0x47 or 0x46 for the BMP581.
Does it measure humidity?
No. Use a BME280 or add a humidity sensor.
What is the BMP585?
A BMP581-class sensor with a ported, gel-filled inlet for wet or dusty places.
Parts for this guide
Calculators
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

