Component guide · Intermediate · 3 min read
BL602, BL616 and RTL8720 Wi-Fi Modules
Ai-WB2, Ai-M61, Ai-M62 and BW16
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Not every low-cost Wi-Fi module is an ESP32. Ai-Thinker's Ai-WB2 uses the Bouffalo BL602, the Ai-M61 and Ai-M62 use the newer BL618 and BL616 with Wi-Fi 6, and the BW16 uses Realtek's RTL8720DN with 2.4 and 5 GHz Wi-Fi. They run at 3.3 V and ship with AT firmware, but use their own SDKs, so ESP32 code does not run on them unchanged.
Key specs at a glance
- BL602 (Ai-WB2)
- RISC-V, Wi-Fi 4 (2.4 GHz), BLE 5
- BL616 / BL618 (Ai-M62 / Ai-M61, AiPi boards)
- RISC-V, Wi-Fi 6 (2.4 GHz), BLE 5.3, 802.15.4
- RTL8720DN (BW16)
- Arm Cortex-M, dual-band 2.4 and 5 GHz Wi-Fi, BLE 5
- Supply and logic
- 3.3 V
- Default firmware
- AT commands over UART
- Programming
- Vendor SDKs; Arduino support for BW16 through the Realtek Ameba core
Which chip is in which module
Read the chip name in the listing title; it decides which tools and libraries you use.
| Module or board | Chip | Wireless | Tools |
|---|---|---|---|
| Ai-WB2-01S, -12F, -M1 | Bouffalo BL602 | Wi-Fi 4, BLE 5 | Ai-Thinker AT firmware, Bouffalo SDK |
| Ai-M61-32S, AiPi boards | Bouffalo BL618 | Wi-Fi 6, BLE 5.3, 802.15.4 | Bouffalo SDK, AT firmware |
| Ai-M62-32S | Bouffalo BL616 | Wi-Fi 6, BLE 5.3, 802.15.4 | Bouffalo SDK, AT firmware |
| BW16, BW20 kits | Realtek RTL8720DN family | Wi-Fi 2.4 and 5 GHz, BLE 5 | Realtek Ameba Arduino core, AT firmware |
- Ai-WB2-01S, -12F, -M1
- Chip:
- Bouffalo BL602
- Wireless:
- Wi-Fi 4, BLE 5
- Tools:
- Ai-Thinker AT firmware, Bouffalo SDK
- Ai-M61-32S, AiPi boards
- Chip:
- Bouffalo BL618
- Wireless:
- Wi-Fi 6, BLE 5.3, 802.15.4
- Tools:
- Bouffalo SDK, AT firmware
- Ai-M62-32S
- Chip:
- Bouffalo BL616
- Wireless:
- Wi-Fi 6, BLE 5.3, 802.15.4
- Tools:
- Bouffalo SDK, AT firmware
- BW16, BW20 kits
- Chip:
- Realtek RTL8720DN family
- Wireless:
- Wi-Fi 2.4 and 5 GHz, BLE 5
- Tools:
- Realtek Ameba Arduino core, AT firmware
Why pick one over an ESP32
the BW16 joins 5 GHz networks, which no ESP8266 and only the newest ESP32 chips do.
the BL616 and BL618 modules support Wi-Fi 6 and Thread or Zigbee radios.
if a main microcontroller only needs a serial-to-Wi-Fi link, any of them works with AT commands.
Pick an ESP32 instead when you want the largest choice of libraries, tutorials and Arduino examples.
Wiring and first test
- Power from a 3.3 V regulator rated for at least 500 mA, with a 100 µF capacitor close to the module.
- Connect UART TX and RX crossed to a USB-to-TTL adapter at 3.3 V logic.
- Hold EN high. Each module has a boot or burn pin for flashing; check the module's pin table before wiring.
- Open a serial monitor at 115200 baud and send
AT. A reply ofOKconfirms power and wiring. - AiPi development boards (AiPi-Eyes, AiPi-Audio, AiPi-Knob) have USB, so plug them in and follow Ai-Thinker's examples for the display or audio parts.
What you need
Shop this list3 of 3 found in our store · ₹391
A module or board such as the Ai-WB2-32S, Ai-M62-32S or BW16Ai-WB2-32S Wi-Fi & BLE 5.0 Module₹197Closest match, check the specs
A USB-to-TTL adapter set to 3.3 VUSB Wall Adapter with Cable (5V)₹145Closest match, check the specs
Jumper wiresDupont Jumper Wires (40 pcs)₹49
Common mistakes to avoid
- Expecting ESP32 Arduino sketches and libraries to run unchanged.
- Powering the module from a 5 V pin or connecting 5 V UART signals.
- Leaving the boot pin in flash mode, so the module never runs its firmware.
- Assuming every Wi-Fi 6 module also does 5 GHz; BL616 and BL618 are 2.4 GHz only.
Frequently asked questions
Can I program these with the Arduino IDE?
The BW16 (RTL8720DN) has a Realtek Ameba Arduino core. The Bouffalo modules are mainly programmed with the Bouffalo SDK; Arduino support is limited.
Which one supports 5 GHz Wi-Fi?
The RTL8720DN modules such as the BW16. The BL602, BL616 and BL618 work on 2.4 GHz only.
Do they work as a Wi-Fi add-on for Arduino Uno?
Yes, with the AT firmware over serial, using a level shifter on the Uno's TX line.
Is the Ai-M61 an ESP32?
No. It uses the Bouffalo BL618 chip. It fills a similar role but uses different tools.
What is 802.15.4 used for?
It is the radio layer for Thread and Zigbee, used in smart home devices and Matter.
Parts for this guide
Terms in this guide
Keep learning
Sources
- Bouffalo Lab BL602, BL616 and BL618 datasheets
- Ai-Thinker module specifications (Ai-WB2, Ai-M61-32S, Ai-M62-32S, BW16)
- Realtek Ameba RTL8720DN documentation
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.



