Component guide · Beginner · 3 min read
Breadboard Power Supply Modules (MB102 3.3V/5V, WeAct, Micro USB, Multi-Output)

Guide
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
A breadboard power supply plugs straight into the power rails of a solderless breadboard and gives 3.3 V or 5 V on each side from a USB cable or 6.5 to 12 V DC jack. Jumpers choose the voltage per rail. Multi-output DC-DC modules give 3.3, 5, 9 and 12 V at once for mixed circuits. They are simple bench helpers, not high-current supplies.
Key specs at a glance
- Input
- USB 5 V or 6.5 to 12 V DC jack
- Output
- 3.3 V and 5 V per rail (jumper)
- Current
- About 500 to 700 mA total
- Regulator
- AMS1117 3.3 V and 5 V (MB102)
- Switch
- Power switch and LED
- Multi-output
- 3.3/5/9/12 V modules from a single input
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Breadboard Power Supply Module (3.3V / 5V)₹71
Option 2WeAct Mini DC Power Supply Module₹450
Option 3Micro USB Power Breakout₹16
Option 4Dual USB 5V Power Module with LCD₹189
Option 5Multi-Output DC-DC Power Module (3.3V / 5V / 12V)₹38
Option 6DFRobot Multi-Output DC-DC Buck Converter (3.3V / 5V / 9V / 12V)₹600
What the Breadboard power supply module is
A breadboard power supply is a small board that plugs into the power rails of a solderless breadboard. Its regulators give 3.3 V or 5 V on each rail from a USB cable or a DC adapter.
Plug the module in the right way: the pins marked + and - must sit on the matching breadboard rails. On some breadboards, the rails are split in the middle; bridge them.
The USB input bypasses the 5 V regulator, so 5 V is only as clean as the USB source.
Breadboard power supply module pinout
The pins on the Breadboard power supply module and what each one does.
| Pin | Function |
|---|---|
| Rail pins | + and - into both rail pairs |
| Jumpers | 3.3 V or 5 V per side |
| DC jack | 6.5 to 12 V |
| USB | 5 V input |
| Header | Extra 3.3 V and 5 V pins |
- Rail pins
- + and - into both rail pairs
- Jumpers
- 3.3 V or 5 V per side
- DC jack
- 6.5 to 12 V
- USB
- 5 V input
- Header
- Extra 3.3 V and 5 V pins
Wiring the Breadboard power supply module
Connect the Breadboard power supply module like this.
| Breadboard power supply module pin | Example A | Example B |
|---|---|---|
| Left rail | 5 V for an Uno-type circuit | 3.3 V for ESP32 sensors |
| Right rail | 3.3 V sensors | 5 V relay module |
- Left rail
- Example A:
- 5 V for an Uno-type circuit
- Example B:
- 3.3 V for ESP32 sensors
- Right rail
- Example A:
- 3.3 V sensors
- Example B:
- 5 V relay module
Example code
A minimal sketch to check the part works.
Set jumpers, power on with nothing plugged in,
measure each rail with a multimeter, then add parts.Setup and tuning
check the + and − rails line up with the module before plugging it in.
set each side's jumper to 3.3 V or 5 V, and measure before adding parts.
a 9 V DC adapter is a good choice; 12 V makes the regulators run hot.
keep the total under about 500 mA; motors and servos need their own supply.
on long breadboards, link the two halves of each rail with jumpers.
What you need
Shop this list8 of 9 found in our store · ₹1,729
Breadboard Power Supply Module (3.3V / 5V): the part this guide coversBreadboard Power Supply Module (3.3V / 5V)₹71
WeAct Mini DC Power Supply Module: another version this guide coversWeAct Mini DC Power Supply Module₹450
Micro USB Power Breakout: another version this guide coversMicro USB Power Breakout₹16
Dual USB 5V Power Module with LCD: another version this guide coversDual USB 5V Power Module with LCD₹189
Multi-Output DC-DC Power Module (3.3V / 5V / 12V): another version this guide coversMulti-Output DC-DC Power Module (3.3V / 5V / 12V)₹38
DFRobot Multi-Output DC-DC Buck Converter (3.3V / 5V / 9V / 12V): another version this guide coversDFRobot Multi-Output DC-DC Buck Converter (3.3V / 5V / 9V / 12V)₹600
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
DC power adapter (5.5 x 2.1 mm): a wall adapter inputDC Power Adapter (5.5x2.1mm)₹188- Uno R3 development board: the controller used in the wiring tableFind this part
Alternatives and when to choose them
Common mistakes to avoid
- Plugging it in reversed on the rails.
- Running motors or servos from it.
- Forgetting to bridge split rails on long breadboards.
- Feeding 12 V when 9 V would do.
Frequently asked questions
Can a breadboard power supply run servos?
Only one tiny micro servo at light load. Larger servos and motors need a separate supply.
What input should I use?
Use a USB cable or a 6.5 to 12 V DC adapter; 9 V keeps the regulators coolest.
Can both rails be 5 V?
Yes. Set both jumpers to 5 V.
Why does the module get hot?
Too much current or a high DC input. The linear regulators turn the extra voltage into heat.
Is there a module with more voltages?
Yes. The multi-output module gives 3.3, 5, 9 and 12 V from one input.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

