Component guide · Advanced · 3 min read
Brushless Gimbal Motors

2804 and 2805 140KV, BGM2606 90KV and T-Motor GB4106 for Camera Gimbals and FOC Projects
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Gimbal motors are low-KV brushless motors wound with many turns of thin wire. They hold a position smoothly at low speed instead of spinning fast. Use them in 2 or 3 axis camera gimbals with a gimbal controller, or in robots and balancing projects with a FOC driver such as SimpleFOC. They need an encoder or IMU feedback for good control.
Key specs at a glance
- KV
- About 50 to 140 KV
- Phase resistance
- High, often 5 to 15 ohm, so a low-current driver works
- Supply
- Typically 2S to 4S, 7.4 to 16.8 V
- Hollow shaft
- On many, for cable routing
- Pole pairs
- Usually 7 (14 poles) or 11 (22 poles); check the spec
- Feedback
- Gimbal IMU or a magnetic encoder like AS5600 or AS5048
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 12804 140KV Brushless Gimbal Motor for 2-Axis Cameras₹1,079
Option 2CAELUS BGM2606-90T 90KV Brushless Motor₹3,189
Option 3FLYCCI BGM2606-90 90KV Brushless Motor₹3,029
Option 4FlyCat 2805 140KV Gimbal Brushless Motor₹1,239
Option 5T-Motor GB4106 Precision Gimbal Motor 53KV₹5,059
What the Brushless gimbal motors (2804, 2805, 2606, GB4106) is
Brushless gimbal motors are slow, high-torque outrunners wound for smooth, precise positioning, used to stabilise cameras on gimbals.
For a camera gimbal, choose the motor by camera weight: 2804 or 2805 for small action cameras, 2606 or GB4106 for heavier compact cameras.
For FOC robotics, a gimbal motor with a magnetic encoder makes a smooth, quiet servo. Set the pole-pair count in software and keep the supply current-limited during first tests, because the motor holds full current when stalled.
Brushless gimbal motors (2804, 2805, 2606, GB4106) pinout
The pins on the Brushless gimbal motors (2804, 2805, 2606, GB4106) and what each one does.
| Pin | Function |
|---|---|
| Phase wires | Three wires to the driver |
| Hollow shaft | Cable pass-through on many models |
| Mount holes | M2 or M3 on the stator and bell |
| Magnet mount | Encoder magnet glued to the shaft end |
| Poles | 7 or 11 pole pairs, set in firmware |
- Phase wires
- Three wires to the driver
- Hollow shaft
- Cable pass-through on many models
- Mount holes
- M2 or M3 on the stator and bell
- Magnet mount
- Encoder magnet glued to the shaft end
- Poles
- 7 or 11 pole pairs, set in firmware
Wiring the Brushless gimbal motors (2804, 2805, 2606, GB4106)
A stalled gimbal motor at full voltage gets hot. Set a voltage limit in the driver firmware.
| Brushless gimbal motors (2804, 2805, 2606, GB4106) pin | Connection | Note |
|---|---|---|
| Phases A, B, C | FOC or gimbal driver outputs | Any order, calibrate after |
| Driver power | 2S to 4S supply | Current-limited bench supply for tests |
| Encoder | I2C or SPI to the MCU | Magnet centred over the sensor |
- Phases A, B, C
- Connection:
- FOC or gimbal driver outputs
- Note:
- Any order, calibrate after
- Driver power
- Connection:
- 2S to 4S supply
- Note:
- Current-limited bench supply for tests
- Encoder
- Connection:
- I2C or SPI to the MCU
- Note:
- Magnet centred over the sensor
Example code
The same steps apply in most FOC libraries; names follow SimpleFOC.
1. Set pole pairs to the motor's value (for example 7 for 2804).
2. Set a voltage limit of about 2 to 3 V for the first test.
3. Run open-loop velocity mode at 2 rad/s and check smooth rotation.
4. Add the encoder, run sensor alignment, then switch to closed-loop angle mode.
5. Tune the velocity PID before raising the voltage limit.Setup and tuning
use a gimbal controller (such as SimpleBGC or STorM32) or a FOC driver, not a drone ESC.
balance the camera on each axis so the motor holds it with little current.
set motor power in the controller; too high makes motors hot, too low makes them drift.
use the encoder version when you need exact angles.
keep the three motor wires tidy so they cannot catch as the gimbal moves.
What you need
Shop this list5 of 6 found in our store · ₹30,38,032
2804 140KV Brushless Gimbal Motor for 2-Axis Cameras: the part this guide covers2804 140KV Brushless Gimbal Motor for 2-Axis Cameras₹1,079Closest match, check the specs
CAELUS BGM2606-90T 90KV Brushless Motor: another version this guide coversCAELUS BGM2606-90T 90KV Brushless Motor₹3,189
FLYCCI BGM2606-90 90KV Brushless Motor: another version this guide coversFLYCCI BGM2606-90 90KV Brushless Motor₹3,029
FlyCat 2805 140KV Gimbal Brushless Motor: another version this guide coversFlyCat 2805 140KV Gimbal Brushless Motor₹1,239
T-Motor GB4106 Precision Gimbal Motor 53KV: another version this guide coversT-Motor GB4106 Precision Gimbal Motor 53KV₹5,059- Laser tachometer: to check motor RPM against the KV ratingFind this part
Alternatives and when to choose them
- SimpleFOC Mini BLDC driver: a matching driver.
- 5 inch FPV motors: high-KV motors for props.
Common mistakes to avoid
- Using a drone ESC to drive a gimbal motor.
- Running an unbalanced camera, so motors overheat.
- Setting motor power too high.
- Letting motor wires catch on the moving frame.
Frequently asked questions
Can I drive a gimbal motor with a normal ESC?
No. Drone ESCs spin motors fast; gimbal motors need a gimbal controller or FOC driver.
Why does my gimbal motor get hot?
The camera is not balanced or the power setting is too high.
What does 140 KV mean on a gimbal motor?
It means low speed and high torque per amp, suiting slow, precise movement.
Can I use gimbal motors in robots?
Yes. With a FOC driver like SimpleFOC, they make smooth, quiet robot joints.
Which size do I need?
Small 2804 to 2805 motors suit action cameras; larger GB4106 motors suit heavier cameras.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

