Component guide · Beginner · 3 min read
Cytron SC08A 8-Channel Serial Servo Controller and Servo Shield

Wiring and Code
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The Cytron SC08A drives up to eight PWM servos from simple UART commands, freeing the microcontroller from timing every pulse. You send a channel, position and speed, and it handles smooth moves. The Cytron 8-channel servo shield puts the same idea on an Arduino shield with a separate servo power terminal. Both suit small arms and walking robots.
Key specs at a glance
- Channels
- 8 PWM servos
- Interface
- UART, 9600 to 115200 baud (auto)
- Position resolution
- Fine-step positioning, 0.5 to 2.5 ms
- Speed control
- Per channel
- Servo supply
- Separate terminal, 4.8 to 7.2 V
- Logic supply
- 5 V
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Cytron SC08A 8-Channel Serial Servo Controller₹1,780
Option 2Cytron 8-Channel Servo Shield for Arduino₹2,047
What the Cytron SC08A servo controller is
The Cytron SC08A takes simple serial commands and generates the PWM pulses for up to eight servos, including smooth speed-controlled moves.
Keep servo power on its own terminal and logic on 5 V, with a shared ground. The board can also report the current position of each channel, which helps when stopping mid-move.
Several SC08A boards can share a serial line by setting different board addresses.
Cytron SC08A servo controller pinout
The pins on the Cytron SC08A servo controller and what each one does.
| Pin | Function |
|---|---|
| VS+ / GND | Servo power |
| 5V / GND | Logic power |
| TX / RX | UART |
| CH1 to CH8 | Servo headers |
- VS+ / GND
- Servo power
- 5V / GND
- Logic power
- TX / RX
- UART
- CH1 to CH8
- Servo headers
Wiring the Cytron SC08A servo controller
Connect the Cytron SC08A servo controller like this.
| Cytron SC08A servo controller pin | Arduino Uno | ESP32 |
|---|---|---|
| RX | D3 (SoftwareSerial TX) | GPIO 17 |
| TX | D2 (SoftwareSerial RX) | GPIO 16 |
| 5V / GND | 5V / GND | 5V (VIN) / GND |
- RX
- Arduino Uno:
- D3 (SoftwareSerial TX)
- ESP32:
- GPIO 17
- TX
- Arduino Uno:
- D2 (SoftwareSerial RX)
- ESP32:
- GPIO 16
- 5V / GND
- Arduino Uno:
- 5V / GND
- ESP32:
- 5V (VIN) / GND
Example code
Check the SC08A user manual for the exact position range on your board version.
#include <SoftwareSerial.h>
SoftwareSerial sc(2, 3);
void servo(uint8_t ch, uint16_t pos, uint8_t speed) {
sc.write(0xE0 | ch); // position + speed command
sc.write((pos >> 6) & 0x7F);
sc.write(pos & 0x3F);
sc.write(speed);
}
void setup() {
sc.begin(9600);
sc.write(0xC0 | 1); sc.write(1); // turn on channel 1
}
void loop() { servo(1, 1000, 50); delay(2000); servo(1, 7000, 50); delay(2000); }Setup and tuning
feed servos from the servo terminal at 4.8 to 7.2 V; do not power them from the Arduino.
connect the controller, servo supply and Arduino grounds together.
the SC08A detects the baud rate automatically; send the first byte after power-up.
use the speed value for smooth motion instead of jumping between positions.
set start positions before enabling servos so they do not jump.
What you need
Shop this list5 of 6 found in our store · ₹4,536
Cytron SC08A 8-Channel Serial Servo Controller: the part this guide coversCytron SC08A 8-Channel Serial Servo Controller₹1,780
Cytron 8-Channel Servo Shield for Arduino: another version this guide coversCytron 8-Channel Servo Shield for Arduino₹2,047- Uno R3 development board: the controller used in the wiring tableFind this part
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
XL4015 5A buck converter with voltmeter: a separate 5 to 6 V supply for the servosXL4015 5A Buck Converter with Voltmeter₹304
Electrolytic capacitor: bulk capacitance across the supplyElectrolytic Capacitor₹16
Alternatives and when to choose them
- PCA9685 servo driver: I2C, 16 channels.
- Hiwonder LSC controllers: stored action groups.
- Servo motors overview.
Common mistakes to avoid
- Powering servos from the Arduino's 5 V pin.
- Leaving grounds unconnected.
- Enabling servos before setting their start positions.
- Using a supply too small for several servos.
Frequently asked questions
Why use the SC08A instead of the Servo library?
It frees the microcontroller from pulse timing and adds smooth speed control on eight channels.
Can I power servos from the Arduino 5 V pin?
No. Use a separate supply on the servo terminal sized for all servos.
Which baud rate does it use?
It detects the baud rate automatically from the first byte you send.
Can I use it with an ESP32?
Yes, over UART with level shifting if needed.
Why do my servos jitter?
Usually the servo supply sags. Use a stronger supply and thicker wires.
Parts for this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

