Component guide · Beginner · 3 min read
Hiwonder LSC-6, LSC-16, LSC-24 and LSC-32 Servo Controllers

Setup and Serial Commands
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Hiwonder LSC boards are standalone PWM servo controllers with 6, 16, 24 or 32 channels. You record poses as action groups with the PC software or phone app, store them on the board, and play them back by button, Bluetooth or a serial command from an Arduino or ESP32. They are popular for robot arms and hexapods.
Key specs at a glance
- Channels
- 6 (LSC-6), 16, 24 or 32
- Servo supply
- 5 to 8.4 V via screw terminal
- Logic
- Onboard MCU with action group storage
- Control
- USB, Bluetooth (LSC-6), UART TTL, PS2 on some models
- Signal
- PWM 500 to 2500 us
- Storage
- Action groups saved on flash
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Hiwonder LSC Servo Controller (16, 24 and 32 Channel)₹2,450
Option 2Hiwonder LSC-6 6-Channel Bluetooth Servo Controller₹3,200
What the Hiwonder LSC servo controller is
Hiwonder LSC servo controllers drive 6, 16, 24 or 32 PWM servos from one board, with saved action groups, a PC or phone app and serial control from Arduino or Raspberry Pi.
The board powers every servo from its terminal, so a strong 2S battery or 7.4 V supply is needed. The logic is isolated from servo spikes better than a breadboard setup.
From a microcontroller you can move a servo directly or call an action group number with a short serial packet.
Hiwonder LSC servo controller pinout
The pins on the Hiwonder LSC servo controller and what each one does.
| Pin | Function |
|---|---|
| Power terminal | Servo supply |
| Servo headers | GND, V+, signal per channel |
| UART | TX, RX, GND for a controller |
| USB | PC software |
- Power terminal
- Servo supply
- Servo headers
- GND, V+, signal per channel
- UART
- TX, RX, GND for a controller
- USB
- PC software
Wiring the Hiwonder LSC servo controller
Connect the Hiwonder LSC servo controller like this.
| Hiwonder LSC servo controller pin | Arduino Uno | ESP32 |
|---|---|---|
| RX | D1 (TX) or SoftwareSerial TX | GPIO 17 (TX2) |
| TX | D0 (RX) | GPIO 16 (RX2) |
| GND | GND | GND |
- RX
- Arduino Uno:
- D1 (TX) or SoftwareSerial TX
- ESP32:
- GPIO 17 (TX2)
- TX
- Arduino Uno:
- D0 (RX)
- ESP32:
- GPIO 16 (RX2)
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
Example code
Disconnect the board from the Uno's TX/RX while uploading sketches.
void runGroup(uint8_t group, uint16_t times) {
uint8_t b[7] = {0x55, 0x55, 5, 6, group, (uint8_t)times, (uint8_t)(times >> 8)};
Serial.write(b, 7);
}
void setup() { Serial.begin(9600); delay(1000); runGroup(1, 1); }
void loop() {}Setup and tuning
connect servo power (5 to 8.4 V) to the power input; the board logic is powered separately or from it per the manual.
plug signal, power and ground in the right orientation on each channel.
use the Hiwonder PC or phone app to move servos and record action groups.
send commands from Arduino or Pi to the UART at the stated baud rate.
trigger saved action groups by number from code or the app.
What you need
Shop this list4 of 5 found in our store · ₹6,337
Hiwonder LSC Servo Controller (16, 24 and 32 Channel): the part this guide coversHiwonder LSC Servo Controller (16, 24 and 32 Channel)₹2,450
Hiwonder LSC-6 6-Channel Bluetooth Servo Controller: another version this guide coversHiwonder LSC-6 6-Channel Bluetooth Servo Controller₹3,200- Uno R3 development board: the controller used in the wiring tableFind this part
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
SMPS power supply in metal enclosure (5/12/24 V): a bench supply for servo projectsSMPS Power Supply, Metal Enclosure (5V / 12V / 24V)₹298Closest match, check the specs
Alternatives and when to choose them
- PCA9685 servo driver: cheaper, needs code for everything.
- Cytron SC08A: 8-channel serial controller.
- Hiwonder LD servos.
Common mistakes to avoid
- Powering many servos from a weak adapter.
- Plugging servo leads in reversed.
- Using wrong baud rate.
- Connecting bus servos.
Frequently asked questions
How do I control the LSC board from Arduino?
Send the serial commands from the Hiwonder protocol over the UART.
What is an action group?
A saved sequence of servo positions, like a robot walking or waving.
Why do servos move weakly or reset the board?
The supply cannot give enough current; use a stronger supply.
Can I connect bus servos to the LSC?
No. LSC boards are for PWM servos; bus servos need a bus controller.
How many servos can move at once?
All channels can move, but your supply must cover their total current.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

