Component guide · Beginner · 3 min read
Cytron URC10 Sumo Robot Controller and UNO Robot Controller

Setup and Code
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The Cytron URC10 is an Arduino-compatible controller made for sumo robots. It combines an ATmega328P, a dual 10 A motor driver, buttons, LEDs, a buzzer, and ports for opponent and edge sensors in one board. You program it like an Uno. The Cytron dual 10 A UNO robot controller is a similar all-in-one board for bigger robots.
Key specs at a glance
- MCU
- ATmega328P (Arduino Uno compatible)
- Motor driver
- Dual channel, about 10 A continuous each
- Supply
- 7 to 25 V
- Inputs
- Opponent and edge sensor ports, start module
- Extras
- Buttons, LEDs, buzzer
- Programming
- USB, Arduino IDE as Uno
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Cytron URC10 Sumo Robot Controller R1.1₹4,044
Option 2Cytron Dual Channel 10A Motor Driver UNO Robot Controller₹4,048
What the Cytron URC10 sumo robot controller is
The Cytron URC10 is a single board for small sumo robots that combines an Arduino Uno compatible microcontroller with a dual motor driver and ready-made sensor ports, so a whole robot needs only motors, sensors and a battery.
A sumo robot needs to wait five seconds after start, then hunt and push while avoiding the ring edge. The board's sensor ports are laid out for that: infrared opponent sensors on the front and sides, line sensors underneath.
Use a 3S LiPo or similar; sumo motors draw high stall current when robots push against each other.
Cytron URC10 sumo robot controller pinout
The pins on the Cytron URC10 sumo robot controller and what each one does.
| Pin | Function |
|---|---|
| Battery in | 7 to 25 V |
| M1, M2 | Motor outputs |
| Sensor ports | Opponent and edge sensors |
| Start | Start module or button |
| USB | Programming |
- Battery in
- 7 to 25 V
- M1, M2
- Motor outputs
- Sensor ports
- Opponent and edge sensors
- Start
- Start module or button
- USB
- Programming
Wiring the Cytron URC10 sumo robot controller
Connect the Cytron URC10 sumo robot controller like this.
| Cytron URC10 sumo robot controller pin | URC10 | UNO robot controller |
|---|---|---|
| Left motor | M1 | M1 |
| Right motor | M2 | M2 |
| Sensors | Labelled ports | Labelled ports |
- Left motor
- URC10:
- M1
- UNO robot controller:
- M1
- Right motor
- URC10:
- M2
- UNO robot controller:
- M2
- Sensors
- URC10:
- Labelled ports
- UNO robot controller:
- Labelled ports
Example code
Replace pin numbers with the ones in the Cytron URC10 user manual.
// Pin numbers: check the URC10 pin map.
const int PWM_L = 10, DIR_L = 12, PWM_R = 9, DIR_R = 11, START = 2;
void motors(int l, int r) {
digitalWrite(DIR_L, l >= 0); analogWrite(PWM_L, abs(l));
digitalWrite(DIR_R, r >= 0); analogWrite(PWM_R, abs(r));
}
void setup() {
pinMode(DIR_L, OUTPUT); pinMode(DIR_R, OUTPUT); pinMode(START, INPUT_PULLUP);
while (digitalRead(START)) {}
delay(5000);
}
void loop() { motors(120, -120); }Setup and tuning
select Arduino Uno as the board and the URC10's USB port; no extra board package is needed.
code the 5 second wait after the start button or start module before the motors move, as competition rules require.
calibrate the line sensors on the real ring surface, because a printed ring and a painted ring read differently.
use a 3S LiPo or a pack inside 7 to 25 V, with a fuse and thick wires; pushing robots draw high stall current.
test each motor at low speed first and swap wires or invert it in code so forward is forward.
What you need
Shop this list3 of 3 found in our store · ₹8,108
Cytron URC10 Sumo Robot Controller R1.1: the part this guide coversCytron URC10 Sumo Robot Controller R1.1₹4,044
Cytron Dual Channel 10A Motor Driver UNO Robot Controller: another version this guide coversCytron Dual Channel 10A Motor Driver UNO Robot Controller₹4,048
Electrolytic capacitor: bulk capacitance across the supplyElectrolytic Capacitor₹16
Alternatives and when to choose them
- Cytron MDD10A: driver only.
- Motor drivers overview.
Common mistakes to avoid
- Forgetting the 5 second start delay, which disqualifies the robot in competitions.
- Using edge sensor thresholds from the bench instead of calibrating on the ring.
- Running from a weak battery so the board resets when the motors push.
- Leaving the battery unfused, so a short melts wires.
Frequently asked questions
Is the URC10 Arduino compatible?
Yes. It uses an ATmega328P, so you program it in the Arduino IDE by selecting Arduino Uno.
How much motor current can it handle?
About 10 A continuous per channel, which suits the geared motors used in mini and mega sumo robots.
What battery should I use?
Any battery from 7 to 25 V. A 3S LiPo is common because it gives strong pushing power in a small size.
Do I need a separate motor driver?
No. The dual motor driver is built into the board, with screw terminals for both motors.
Can I use it for robots other than sumo?
Yes. Any small two-motor robot such as a line follower or an obstacle avoider can use it.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
