Component guide · Beginner · 4 min read
DFRobot Fermion MEMS Gas Sensors

CO, Ethanol, HCHO, H2S, H2, CH4, NH3, NO2, Odor, Smoke, VOC) and MiCS-5524 / MiCS-2714
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Fermion MEMS gas sensors are tiny metal-oxide sensors on a micro-machined heater, so they draw far less power than MQ sensors and warm up faster. Each board targets one gas, such as CO, methane, ammonia or NO2, and gives an analog voltage. The MiCS-5524 detects CO, alcohol and methane, and the MiCS-2714 detects NO2. Use them for leak alarms and trends, not certified readings.
Key specs at a glance
- Supply
- 3.3 to 5 V
- Heater power
- About 20 to 80 mW (far lower than MQ sensors)
- Output
- Analog voltage
- Warm-up
- A few minutes; first use needs a long burn-in
- Ranges
- From 0.1 to 10 ppm (NO2) up to 1 to 10,000 ppm (CH4)
- Size
- About 13 x 13 mm boards
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1DFRobot Fermion MEMS CO Gas Sensor (5–5000 ppm) – Analog Voltage Output₹599
Option 2DFRobot Fermion MEMS Ethanol Gas Sensor (1–500 ppm) – Analog Output₹629
Option 3DFRobot Fermion MEMS Formaldehyde Gas Sensor (0–3 ppm) – Analog Voltage Output₹669
Option 4DFRobot Fermion MEMS H2S Gas Sensor (0.5–50 ppm) – Analog Voltage Output₹1,039
Option 5DFRobot Fermion MEMS Hydrogen Gas Sensor (0.1–1000 ppm) – Analog Voltage Output₹1,889
Option 6DFRobot Fermion MEMS Methane Gas Sensor (1–10000 ppm) – Analog Voltage Output₹559
What the DFRobot Fermion MEMS gas sensors is
DFRobot Fermion MEMS gas sensors are small, low-power analog sensors for gases such as CO, ethanol, H2S and NO2, using far less heater power than MQ sensors.
Like all metal-oxide sensors these react to several gases, not only the one on the label. Treat them as a change detector: record clean-air output, then alarm when it moves well past that.
DFRobot publishes a conversion curve for each board; use it to estimate ppm after calibration.
DFRobot Fermion MEMS gas sensors pinout
The pins on the DFRobot Fermion MEMS gas sensors and what each one does.
| Pin | Function |
|---|---|
| VCC | 3.3 to 5 V |
| GND | Ground |
| A / OUT | Analog output |
| EN (MiCS boards) | Heater enable |
- VCC
- 3.3 to 5 V
- GND
- Ground
- A / OUT
- Analog output
- EN (MiCS boards)
- Heater enable
Wiring the DFRobot Fermion MEMS gas sensors
On a 3.3 V board, power the sensor at 3.3 V so the output never exceeds the ADC range.
| DFRobot Fermion MEMS gas sensors pin | Arduino Uno | ESP32 |
|---|---|---|
| VCC | 5 V | 3.3 V |
| GND | GND | GND |
| Analog out | A0 | GPIO 34 |
| EN (MiCS-5524 breakout) | D7 high | GPIO 26 high |
- VCC
- Arduino Uno:
- 5 V
- ESP32:
- 3.3 V
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- Analog out
- Arduino Uno:
- A0
- ESP32:
- GPIO 34
- EN (MiCS-5524 breakout)
- Arduino Uno:
- D7 high
- ESP32:
- GPIO 26 high
Example code
Some boards go up with gas and some go down (NO2 raises resistance). Check the direction for your board.
int baseline;
void setup() {
Serial.begin(115200);
delay(180000); // 3 minutes warm-up
long s = 0;
for (int i = 0; i < 64; i++) { s += analogRead(A0); delay(50); }
baseline = s / 64;
}
void loop() {
int v = analogRead(A0);
Serial.print(v); Serial.print(" baseline "); Serial.println(baseline);
if (abs(v - baseline) > baseline / 3) Serial.println("Gas change detected");
delay(1000);
}Setup and tuning
run new sensors for 24 hours or more before trusting readings.
wait a few minutes after each power-up.
read the output with analogRead and use DFRobot's library or curve to convert to ppm.
3.3 to 5 V; use the same reference for the ADC.
they show trends and alarms well, not certified concentrations.
What you need
Shop this list17 of 19 found in our store · ₹13,201
DFRobot Fermion MEMS CO Gas Sensor (5–5000 ppm) – Analog Voltage Output: the part this guide coversDFRobot Fermion MEMS CO Gas Sensor (5–5000 ppm) – Analog Voltage Output₹599
DFRobot Fermion MEMS Ethanol Gas Sensor (1–500 ppm) – Analog Output: another version this guide coversDFRobot Fermion MEMS Ethanol Gas Sensor (1–500 ppm) – Analog Output₹629
DFRobot Fermion MEMS Formaldehyde Gas Sensor (0–3 ppm) – Analog Voltage Output: another version this guide coversDFRobot Fermion MEMS Formaldehyde Gas Sensor (0–3 ppm) – Analog Voltage Output₹669
DFRobot Fermion MEMS H2S Gas Sensor (0.5–50 ppm) – Analog Voltage Output: another version this guide coversDFRobot Fermion MEMS H2S Gas Sensor (0.5–50 ppm) – Analog Voltage Output₹1,039
DFRobot Fermion MEMS Hydrogen Gas Sensor (0.1–1000 ppm) – Analog Voltage Output: another version this guide coversDFRobot Fermion MEMS Hydrogen Gas Sensor (0.1–1000 ppm) – Analog Voltage Output₹1,889
DFRobot Fermion MEMS Methane Gas Sensor (1–10000 ppm) – Analog Voltage Output: another version this guide coversDFRobot Fermion MEMS Methane Gas Sensor (1–10000 ppm) – Analog Voltage Output₹559
DFRobot Fermion MEMS NH3 Ammonia Gas Sensor (1–300 ppm) – Analog Voltage Output: another version this guide coversDFRobot Fermion MEMS NH3 Ammonia Gas Sensor (1–300 ppm) – Analog Voltage Output₹1,089
DFRobot Fermion MEMS NO2 Gas Sensor (0.1–10 ppm) – Analog Voltage Output: another version this guide coversDFRobot Fermion MEMS NO2 Gas Sensor (0.1–10 ppm) – Analog Voltage Output₹1,049
DFRobot Fermion MEMS Odor Gas Sensor (0.5–50 ppm) – Analog Output: another version this guide coversDFRobot Fermion MEMS Odor Gas Sensor (0.5–50 ppm) – Analog Output₹599
DFRobot Fermion MEMS Smoke Gas Sensor (10–1000 ppm) – Analog Voltage Output: another version this guide coversDFRobot Fermion MEMS Smoke Gas Sensor (10–1000 ppm) – Analog Voltage Output₹599
DFRobot Fermion MEMS VOC Gas Sensor (1–500 ppm) – Analog Voltage Output: another version this guide coversDFRobot Fermion MEMS VOC Gas Sensor (1–500 ppm) – Analog Voltage Output₹559
DFRobot Fermion MEMS Gas Sensor MiCS-5524 Breakout Module – Analog Output: another version this guide coversDFRobot Fermion MEMS Gas Sensor MiCS-5524 Breakout Module – Analog Output₹1,039
DFRobot Fermion MEMS Gas Sensor – MiCS-2714 Breakout Module: another version this guide coversDFRobot Fermion MEMS Gas Sensor – MiCS-2714 Breakout Module₹1,079
MICS-5524 CO H2 CH4 Gas Sensor Detection Module – Analog Output: another version this guide coversMICS-5524 CO H2 CH4 Gas Sensor Detection Module – Analog Output₹1,249- Uno R3 development board: the controller used in the wiring tableFind this part
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
Buzzer module 3.3-5 V: for an audible alarmBuzzer Module 3.3–5V₹27
0.96 inch OLED display 128x64: to show readings without a computer0.96" OLED Display 128x64₹139Closest match, check the specs- MQ-7 CO sensor module: a low-cost CO sensor to compare againstFind this part
Alternatives and when to choose them
- MQ gas sensors: larger, more power, very common.
- MiCS-6814 and MiCS-4514: three gases on one board.
- DFRobot Gravity calibrated sensors: real ppm.
Common mistakes to avoid
- Trusting readings before burn-in.
- Treating the result as certified ppm.
- Using a different ADC reference from the supply.
- Expecting perfect selectivity for one gas.
Frequently asked questions
How are MEMS gas sensors different from MQ sensors?
They use much less heater power and are smaller, which suits battery projects.
Do MEMS gas sensors need burn-in?
Yes. Run them for a day or more when new for stable readings.
Can I measure exact ppm?
Only approximately. Calibrate against a reference for better accuracy.
Do they react to other gases?
Yes. Most respond to several gases, so readings are not perfectly selective.
Can I run them from a battery?
Yes. Their low heater power suits battery devices better than MQ sensors.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


