Component guide · Intermediate · 3 min read
MiCS-6814 and MiCS-4514 Multi-Gas Sensors

CO, NO2, NH3) and Grove Multichannel Gas Sensor v2
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The MiCS-6814 has three metal-oxide sensors in one package: a reducing channel (CO, alcohol, hydrogen), an oxidising channel (NO2) and an ammonia channel. The MiCS-4514 has two channels (reducing and NO2). The DFRobot Gravity board reads the MiCS-4514 over I2C, while the Mikroe click and plain modules give analog outputs. The Grove Multichannel v2 uses four separate GM MEMS sensors.
Key specs at a glance
- Channels
- RED, OX, NH3 (MiCS-6814); RED, OX (MiCS-4514)
- Gases
- CO 1 to 1000 ppm, NO2 0.05 to 10 ppm, NH3 1 to 500 ppm (approximate)
- Supply
- 5 V heater (bare), 3.3 to 5 V boards
- Interface
- Analog (bare, modules, Mikroe), I2C (DFRobot Gravity, Grove v2)
- Warm-up
- About 3 minutes; days of burn-in for best stability
- Heater
- About 75 to 90 mW per channel
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1MICS-6814 Gas Sensor Module – VOC, NO2, NH3 Detection₹3,999
Option 2Mikroe Air Quality 5 Click (Mikroe-3056) – MiCS-6814 Triple MOS Gas Sensor Board, I²C, Multi-Gas Detection, 3.3V/5V, mikroBUS₹7,139
Option 3DFRobot Gravity MEMS Gas Sensor (CO, Alcohol, NO2 & NH3) – I2C – MiCS-4514₹5,401
Option 4Amphenol SGX Sensortech MiCS-4514 Multi-Gas Sensor – NH3, CO, Ethanol, H2, CH4, NO2 Detection₹1,409
Option 5Amphenol SGX Sensortech Multi-Gas Detection Sensor NH3, CO, CH3OH, H2, CH4 10-1000ppm₹1,159
Option 6Amphenol SGX Sensortech Multi-Gas Sensor NH3, Ethanol, H2, Propane, Iso-butane 300ppm₹1,581
What the MiCS-6814 and MiCS-4514 multi-gas sensors is
The SGX MiCS-6814 and MiCS-4514 are MEMS metal-oxide gas sensors with separate elements for reducing gases (CO), oxidising gases (NO2) and, on the 6814, ammonia.
Each channel is a resistor that changes with gas. Readings are relative, so log the clean-air value for each channel and watch the ratio.
The DFRobot Gravity MiCS-4514 board has a library that estimates CO, NO2, NH3 and alcohol ppm from those ratios.
MiCS-6814 and MiCS-4514 multi-gas sensors pinout
The pins on the MiCS-6814 and MiCS-4514 multi-gas sensors and what each one does.
| Pin | Function |
|---|---|
| VCC / GND | Power |
| RED, OX, NH3 | Analog outputs (analog boards) |
| SDA / SCL | I2C (Gravity, Grove v2) |
| EN / PRE | Heater enable on some boards |
- VCC / GND
- Power
- RED, OX, NH3
- Analog outputs (analog boards)
- SDA / SCL
- I2C (Gravity, Grove v2)
- EN / PRE
- Heater enable on some boards
Wiring the MiCS-6814 and MiCS-4514 multi-gas sensors
Connect the MiCS-6814 and MiCS-4514 multi-gas sensors like this.
| MiCS-6814 and MiCS-4514 multi-gas sensors pin | Arduino Uno | ESP32 |
|---|---|---|
| VCC | 5 V | 5 V (VIN) |
| GND | GND | GND |
| SDA / SCL (I2C boards) | A4 / A5 | GPIO 21 / 22 |
| RED / OX / NH3 (analog boards) | A0 / A1 / A2 | GPIO 34 / 35 / 32 |
- VCC
- Arduino Uno:
- 5 V
- ESP32:
- 5 V (VIN)
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- SDA / SCL (I2C boards)
- Arduino Uno:
- A4 / A5
- ESP32:
- GPIO 21 / 22
- RED / OX / NH3 (analog boards)
- Arduino Uno:
- A0 / A1 / A2
- ESP32:
- GPIO 34 / 35 / 32
Example code
A minimal sketch to check the part works.
#include <DFRobot_MICS.h>
DFRobot_MICS_I2C mics(&Wire, 0x75);
void setup() {
Serial.begin(115200);
while (!mics.begin()) { Serial.println("No MiCS board"); delay(1000); }
if (mics.getPowerState() == SLEEP_MODE) mics.wakeUpMode();
while (!mics.warmUpTime(3)) delay(1000); // 3 minutes
}
void loop() {
Serial.print("CO "); Serial.print(mics.getGasData(CO));
Serial.print(" ppm NO2 "); Serial.print(mics.getGasData(NO2));
Serial.println(" ppm");
delay(1000);
}Setup and tuning
most come on Grove or breakout boards with I2C or analog outputs.
the sensor heaters need about 5 V and some tens of mA; let them warm.
allow 24 hours on first use and a few minutes each start.
record clean air resistances (R0) and use the datasheet curves.
for indicative trends only, not certified measurement.
What you need
Shop this list11 of 12 found in our store · ₹25,098
MICS-6814 Gas Sensor Module – VOC, NO2, NH3 Detection: the part this guide coversMICS-6814 Gas Sensor Module – VOC, NO2, NH3 Detection₹3,999
Mikroe Air Quality 5 Click (Mikroe-3056) – MiCS-6814 Triple MOS Gas Sensor Board, I²C, Multi-Gas Detection, 3.3V/5V, mikroBUS: another version this guide coversMikroe Air Quality 5 Click (Mikroe-3056) – MiCS-6814 Triple MOS Gas Sensor Board, I²C, Multi-Gas Detection, 3.3V/5V, mikroBUS₹7,139
DFRobot Gravity MEMS Gas Sensor (CO, Alcohol, NO2 & NH3) – I2C – MiCS-4514: another version this guide coversDFRobot Gravity MEMS Gas Sensor (CO, Alcohol, NO2 & NH3) – I2C – MiCS-4514₹5,401
Amphenol SGX Sensortech MiCS-4514 Multi-Gas Sensor – NH3, CO, Ethanol, H2, CH4, NO2 Detection: another version this guide coversAmphenol SGX Sensortech MiCS-4514 Multi-Gas Sensor – NH3, CO, Ethanol, H2, CH4, NO2 Detection₹1,409
Amphenol SGX Sensortech Multi-Gas Detection Sensor NH3, CO, CH3OH, H2, CH4 10-1000ppm: another version this guide coversAmphenol SGX Sensortech Multi-Gas Detection Sensor NH3, CO, CH3OH, H2, CH4 10-1000ppm₹1,159
Amphenol SGX Sensortech Multi-Gas Sensor NH3, Ethanol, H2, Propane, Iso-butane 300ppm: another version this guide coversAmphenol SGX Sensortech Multi-Gas Sensor NH3, Ethanol, H2, Propane, Iso-butane 300ppm₹1,581
Seeed Studio Studio Grove Multichannel Gas Sensor v2 – GM-102B/302B/502B/702B MEMS Sensors w/ STM32F030 & I2C Interface: another version this guide coversSeeed Studio Grove Multichannel Gas Sensor v2 – GM-102B/302B/502B/702B MEMS Sensors w/ STM32F030 & I2C Interface₹3,569- Uno R3 development board: the controller used in the wiring tableFind this part
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
ADS1115 16-bit 4-channel ADC module: to read small sensor voltages accuratelyADS1115 16-Bit 4-Channel ADC Module₹199
0.96 inch OLED display 128x64: to show readings without a computer0.96" OLED Display 128x64₹139Closest match, check the specs
MQ-135 air quality sensor module: a low-cost general air quality sensorMQ-135 Air Quality & Gas Detector Sensor Module for Arduino – Analog & TTL Output₹114Closest match, check the specs
Alternatives and when to choose them
- DFRobot Fermion MEMS sensors: one gas per board.
- Electrochemical gas sensors: accurate NO2 and CO.
- Air quality sensors: overview.
Common mistakes to avoid
- Reading before warm-up.
- Trusting raw ppm.
- Using it as a safety alarm.
- Ignoring humidity effects.
Frequently asked questions
Which gases can the MiCS-6814 detect?
CO and other reducing gases, NO2 and ammonia, with three elements.
Can it give exact ppm values?
Only roughly, after calibration against a known gas.
How long does it need to warm up?
About a day of burn-in on first use, then a few minutes each time it starts.
Why do readings change with humidity?
Metal-oxide sensors change resistance with humidity and temperature, so compensate for both.
Can I use it for safety alarms?
No. Use certified gas detectors anywhere people's safety depends on it.
Parts for this guide
- ₹3,999View
Mikroe Air Quality 5 Click (Mikroe-3056) – MiCS-6814 Triple MOS Gas Sensor Board, I²C, Multi-Gas Detection, 3.3V/5V, mikroBUS₹7,139View- ₹5,401View
- ₹1,409View
- ₹1,159View
- ₹1,581View
Seeed Studio Grove Multichannel Gas Sensor v2 – GM-102B/302B/502B/702B MEMS Sensors w/ STM32F030 & I2C Interface₹3,569View- ₹359View
- ₹389View
- ₹199View
- ₹139View
- ₹114View
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

