Component guide · Advanced · 3 min read
EGS002 Pure Sine Wave Inverter Driver

EG8010 + IR2113) and 12V to 220V Inverter Modules
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The EGS002 board combines the EG8010 SPWM generator with two IR2113 high-side drivers. It drives a full-bridge MOSFET stage fed from a high-voltage DC bus to make a 50 Hz pure sine output, with voltage feedback and over-current protection. The ready 12 V to 220 V inverter modules are complete low-power inverters. Both produce lethal voltages.
Key specs at a glance
- Controller
- EG8010 SPWM
- Drivers
- 2 x IR2113
- Output
- 50 or 60 Hz pure sine (selectable)
- Supply
- 5 V and 12 V to the board
- Feedback
- Voltage, current, temperature inputs
- Inverter module
- 12 V in, 220 V AC out, about 200 W
This part is often wired to 230 V mains. Do all wiring with the plug pulled out, keep mains wires inside a closed box with strain relief, add a fuse, and never touch the board while it is plugged in. If you are new to mains wiring, have an electrician check it before you switch on.
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
What the EGS002 sine inverter driver is
The EGS002 is a control and gate driver board for pure sine inverters. Its EG8010 chip makes sine-weighted PWM, and two IR2113 drivers switch a full-bridge MOSFET stage on a high-voltage DC bus.
The EGS002 needs a DC bus around 310 to 380 V for 220 V output, usually from a boost stage. A typical build is 12 V battery to SG3525 push-pull boost to 350 V DC, then the EGS002 H-bridge with LC filter to 220 V AC.
Use ready inverter modules unless you have experience with high-voltage design.
EGS002 sine inverter driver pinout
The pins on the EGS002 sine inverter driver and what each one does.
| Pin | Function |
|---|---|
| 1, 2 | 12 V and GND |
| HO1, LO1, HO2, LO2 | Gate drive outputs |
| VFB | Voltage feedback |
| IFB | Current feedback |
| TFB | Temperature |
| 5V | Logic supply |
- 1, 2
- 12 V and GND
- HO1, LO1, HO2, LO2
- Gate drive outputs
- VFB
- Voltage feedback
- IFB
- Current feedback
- TFB
- Temperature
- 5V
- Logic supply
Wiring the EGS002 sine inverter driver
Connect the EGS002 sine inverter driver like this.
| EGS002 sine inverter driver pin | EGS002 build | Ready inverter module |
|---|---|---|
| Gate outputs | H-bridge MOSFETs via gate resistors | Built in |
| DC bus | 350 V from boost stage | 12 V battery |
- Gate outputs
- EGS002 build:
- H-bridge MOSFETs via gate resistors
- Ready inverter module:
- Built in
- DC bus
- EGS002 build:
- 350 V from boost stage
- Ready inverter module:
- 12 V battery
Example code
A minimal sketch to check the part works.
- Fuse on battery and DC bus.
- Discharge bus capacitors before touching.
- Test first with a lamp as load and a current-limited supply.
- Insulated enclosure; never touch output while running.Setup and tuning
set 50 Hz for India with the jumper.
set it with the jumpers to suit your MOSFETs.
add an LC filter on the bridge output to turn the SPWM into a clean sine.
test first from a current-limited low-voltage bus with a lamp load, then raise the voltage.
the DC bus and output are lethal; discharge capacitors before touching anything.
What you need
Shop this list4 of 4 found in our store · ₹1,323
EGS002 Pure Sine Wave Inverter Driver Module (EG8010 + IR2113): the part this guide coversEGS002 Pure Sine Wave Inverter Driver Module (EG8010 + IR2113)₹384
12V to 220V DC to AC Inverter Module: another version this guide covers12V to 220V DC to AC Inverter Module₹464
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
SMPS power supply in metal enclosure (5/12/24 V): a bench input supplySMPS Power Supply, Metal Enclosure (5V / 12V / 24V)₹298Closest match, check the specs
Alternatives and when to choose them
- SG3525 PWM controller: boost stage.
- MOSFET gate drivers.
Common mistakes to avoid
- Working on a live DC bus.
- Leaving out fuses on the bus and battery.
- Testing with an expensive or sensitive load first.
- Skipping the dead time setting.
Frequently asked questions
Is the EGS002 a complete inverter?
No. It is only the control and gate driver board. You still need the MOSFET bridge, DC bus, filter and protection.
What DC bus voltage does it need for 220 V output?
About 310 to 380 V DC, usually made by a boost stage from a battery.
How much power does the ready inverter module give?
About 200 W from 12 V input.
Is the output a pure sine wave?
Yes, once the LC filter smooths the SPWM output.
Is this a beginner project?
No. It works with lethal voltages and suits experienced power electronics builders.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
