Component guide · Advanced · 3 min read
MOSFET Gate Drivers and Driver Modules
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
A gate driver is a chip that charges and discharges a MOSFET's gate quickly with an amp or more of current. A microcontroller pin supplies only a few milliamps, so at high PWM frequencies a large MOSFET switches slowly and overheats. Low-side drivers such as the TC4427 drive N-channel MOSFETs to ground. High-side drivers such as the IR2110 use a bootstrap capacitor to drive MOSFETs above the load.
Key specs at a glance
- Peak current
- About 1.5 A (TC4427) to 2 A (IR2110) to charge the gate
- Gate voltage
- Usually 10 to 15 V for standard MOSFETs
- High side
- Bootstrap diode and capacitor, or isolated driver
- Dead time
- Delay between turning one switch off and the other on in a half bridge
- Modules
- Dual-MOSFET PWM modules with optocoupler or driver inputs
- Layout
- Short gate loop, gate resistor 5 to 47 Ω, decoupling at the driver
Why a driver is needed
A MOSFET's gate behaves like a capacitor of several nanofarads. To switch, it must be charged to about 10 V and discharged again. While the gate is between levels, the MOSFET is half on and dissipates a lot of heat. With a 20 mA GPIO pin, switching a large MOSFET can take microseconds; at 20 kHz PWM that time adds up fast.
A gate driver delivers amps for a few nanoseconds, so the transition is short. It also lets a 3.3 V signal produce the 10 to 12 V gate drive that standard MOSFETs need. For slow on and off switching of small loads, a logic-level MOSFET driven directly is fine.
Low-side and high-side drivers
the MOSFET's source is at ground, so a simple driver such as the TC4427 or a transistor push-pull stage can drive it.
in a half or full H-bridge, the upper N-channel MOSFET's source moves with the output. The gate must go 10 V above that point. The IR2110 and similar chips use a bootstrap capacitor charged while the low side is on, which means they cannot hold the high side on at 100 % duty indefinitely.
in a half bridge, both MOSFETs must never be on together, or they short the supply (shoot-through). Half-bridge drivers such as the IR2104 add fixed dead time; with separate inputs, add it in your PWM code.
Layout and protection
- Place the driver close to the MOSFET and keep the gate and return loop short.
- Add a gate resistor (about 10 Ω) to tame ringing, and a 10 kΩ resistor from gate to source so the MOSFET stays off at power-up.
- Put a 1 µF ceramic and a larger electrolytic capacitor at the driver's supply.
- Use flyback diodes or the MOSFET's body diode with care for inductive loads, and a TVS diode on long motor leads.
- Ready-made dual-MOSFET PWM modules suit heaters, LED strips and DC motors in one direction without designing your own.
Try it: Power dissipation calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Driving a big MOSFET at high PWM frequency straight from a GPIO pin.
- Expecting a bootstrap driver to hold the high side on forever.
- No dead time in a half bridge, causing shoot-through.
- Long gate wires that ring and oscillate.
- No gate pull-down, so the MOSFET turns on at power-up.
Frequently asked questions
Do I need a gate driver for a logic-level MOSFET?
Not for on and off switching or low PWM frequencies. At high frequencies or with large MOSFETs, yes.
What does a bootstrap capacitor do?
It stores charge to lift the high-side gate above the source voltage each time the low side turns on.
What is shoot-through?
Both MOSFETs in a half bridge conducting at once, shorting the supply; prevented with dead time.
What gate resistor should I use?
Usually 5 to 47 Ω: lower for faster switching, higher to reduce ringing and noise.
Can an optocoupler drive a MOSFET?
Slowly. Gate-driver optocouplers exist for fast isolated switching.
Parts for this guide
Calculators
Terms in this guide
Keep learning
Sources
- Infineon IR2110 datasheet
- Microchip TC4426/7/8 datasheet
- TI application report SLUA618 on gate drive design
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


