Component guide · Intermediate · 3 min read
High-Current Motor Drivers
BTS7960, IBT-2 and Cytron
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
When an L298N is not enough, a high-current H-bridge module such as the BTS7960 (IBT-2) or a Cytron MD10C drives large DC motors at tens of amps. They use MOSFETs, so they waste far less heat. The BTS7960 has two PWM inputs: RPWM for forward and LPWM for reverse, plus R_EN and L_EN enable pins. Size the driver for your motor's stall current, add a fuse, and use a battery that can supply the surge.
Key specs at a glance
- BTS7960 / IBT-2
- About 6 to 27 V, rated up to 43 A peak (realistic continuous is much lower without extra cooling)
- Inputs
- RPWM, LPWM, R_EN, L_EN, plus R_IS and L_IS current sense
- Logic
- 3.3 to 5 V compatible on most boards (check yours)
- Cytron MD10C / MD20A
- PWM + DIR inputs, 10 or 20 A continuous
- PWM frequency
- Up to about 20 to 25 kHz for silent running
- Protection
- Over-temperature and current limit inside the BTS7960 chips
This part can carry many amps. Use wire thick enough for the current, put a fuse close to the battery, check that connectors are rated for the load and give drivers and motors room to cool. A short at these currents melts wires in seconds.
Wiring a BTS7960 (IBT-2)
- B+ and B− to the battery through a fuse; M+ and M− to the motor.
- VCC to 5 V (or 3.3 V) and GND to the microcontroller ground.
- R_EN and L_EN tied together to 5 V or a GPIO to enable the bridge.
- RPWM and LPWM to two PWM pins.
To drive forward, PWM on RPWM with LPWM at 0; reverse is the opposite. Never set both high, and pause briefly at zero when changing direction under load. Some IBT-2 boards are known for weak logic-side regulators; power VCC from your board rather than relying on it.
Sizing and current
Look up your motor's stall current, which can be 5 to 10 times its running current; that is what the driver sees at start-up or when the robot pushes against a wall. Choose a driver rated comfortably above the running current, add a fuse below the driver's limit, and ramp PWM up over a few hundred milliseconds to soften start-up surges.
Headline peak ratings assume ideal cooling. For long periods at more than about 10 to 15 A, add a fan or bigger heatsink, and watch the board temperature. Use thick wires and good connectors such as XT60 between battery, driver and motor.
Choosing a driver
- Small robots under 2 A: L298N, TB6612FNG or DRV8833 (see motor drivers).
- 5 to 15 A: Cytron MD10C, BTS7960, dual MOSFET drivers.
- Wheelchair motors, lawn robots and go-karts: 20 to 30 A+ drivers with good cooling, or a dedicated motor controller with current limiting.
- For brushless motors, you need an ESC instead.
For your own MOSFET bridge, see MOSFET gate drivers.
Try it: Motor power torque calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Choosing by running current instead of stall current.
- Setting RPWM and LPWM high together.
- No fuse between battery and driver.
- Running near peak current without cooling.
- Thin wires that heat up and drop voltage.
Frequently asked questions
Can the BTS7960 really handle 43 A?
Only briefly with excellent cooling. Plan on much less continuous current on the stock board.
Does the IBT-2 work with ESP32?
Yes on most boards, since inputs accept 3.3 V logic. Test before connecting a big motor.
What PWM frequency should I use?
Around 1 to 20 kHz; higher frequencies are quieter. Check the driver's maximum.
How do I read motor current?
The R_IS and L_IS pins output a current proportional to motor current; read it across a resistor on an analog pin.
L298N or BTS7960?
BTS7960 for anything over about 2 A; it wastes far less power as heat.
Parts for this guide
Calculators
Terms in this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.




