Component guide · Beginner · 3 min read
Fuses, PTC Resettable Fuses and TVS Diodes
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
A fuse melts and opens the circuit when current is too high, protecting wiring and batteries from fire. Choose one rated about 25 to 50% above normal current, with a voltage rating at or above your supply. A PTC resettable fuse does the same by going high-resistance when hot, then recovers when cooled. A TVS diode or MOV clamps voltage spikes. Add a diode or MOSFET for reverse polarity protection.
Key specs at a glance
- Fuse current rating
- About 1.25 to 1.5 times normal operating current
- Fuse types
- Fast-blow for electronics; slow-blow (time-delay) for motors and inrush
- Fuse styles
- 5x20 mm glass, blade (automotive), SMD
- PTC
- Hold current (stays low resistance) and trip current (switches off); resets when cool
- TVS diode
- Clamps fast spikes; choose standoff voltage above normal supply
- MOV
- For mains surges; wears with each large surge
Choosing a fuse
- 1Current: about 1.25 to 1.5 times the normal continuous current, and below what the wire can carry. A 2 A project gets a 3 A fuse; check the wire gauge with the wire gauge guide.
- 2Speed: fast-blow for electronics; slow-blow where motors, lamps or capacitors draw a surge at switch-on.
- 3Voltage: at least the supply voltage. A 32 V automotive fuse must not be used on mains.
- 4Place it as close to the battery or supply as possible, in the positive lead.
Lithium battery packs especially need a fuse, because a short can deliver hundreds of amps; see BMS boards.
PTC resettable fuses
A polymer PTC (polyfuse) is a small part whose resistance rises sharply when it heats. Below its hold current it behaves like a low resistor; above its trip current it heats up and limits current to a trickle until the fault is removed and it cools. The Arduino Uno uses a 500 mA PTC on its USB input.
PTCs are slower than fuses, add some resistance and voltage drop, and do not fully disconnect. They suit USB ports, small motors and places where a user cannot replace a fuse.
Spikes and reverse polarity
TVS diodes respond in nanoseconds and clamp spikes from long cables, motors and static. Pick a standoff voltage just above your normal supply, for example SMBJ5.0A for a 5 V line or SMBJ15A for 12 V. MOVs go across mains inputs to absorb surges.
Reverse polarity: a series Schottky diode is simple but drops about 0.3 to 0.5 V. A P-channel MOSFET in the positive line drops far less and suits higher currents. Alternatively, a diode across the input after a fuse blows the fuse if the supply is reversed.
Try it: Wire gauge calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Fuse rated higher than the wire can carry.
- Automotive 32 V fuses on mains.
- Putting the fuse far from the battery.
- Fast-blow fuse on a motor that blows at every start.
- Assuming a PTC disconnects completely.
Frequently asked questions
What size fuse should I use?
About 1.25 to 1.5 times your normal current, below the wire's rating, with a voltage rating at or above your supply.
What is the difference between fast-blow and slow-blow fuses?
Fast-blow fuses open quickly on overload. Slow-blow fuses tolerate short start-up surges from motors and capacitors.
Is a PTC fuse as good as a normal fuse?
It resets itself, which is convenient, but it is slower and does not fully disconnect. Use real fuses for batteries and high currents.
What does a TVS diode do?
It clamps fast voltage spikes to a safe level, protecting chips from surges and static.
How do I protect against reversed battery connection?
Use a series Schottky diode, a P-channel MOSFET, or a crowbar diode with a fuse.
Parts for this guide
- ₹12View
Calculators
Terms in this guide
Projects that use it
Put this into practice: 2 step-by-step builds in our project library use parts from this guide.
Keep learning
Sources
- Littelfuse fuse selection guide
- Bourns Multifuse PTC application notes
- Vishay SMBJ TVS diode datasheet
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

