Component guide · Beginner · 5 min read
Fingerprint Access Control Boards and USB Readers

Grow K202, K215, K219-A, K220, KL216, KL261, KR501, KS200 and KS220-L Relay Boards, R503 Ring Control Board, Grow R101, R101S, R102 and R105 USB Readers, HFSecurity HF4000 Scanner and X05 Biometric Terminal
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
These let you add fingerprint unlocking without writing code. A fingerprint control board pairs with a sensor such as R503 and switches a relay when an enrolled finger is matched, so it can drive a door strike, solenoid lock or locker. Fingers are enrolled with buttons or a master finger. USB readers such as Grow R101 to R105 and HF4000 plug into a PC for attendance and login software.
Key specs at a glance
- Capacity
- 20 to 200 fingers on control boards; up to 1000 on USB readers
- Output
- Relay, often 10 A, NO/NC; some with dual relays
- Supply
- 3.7-10 V, 5.5-15 V, 12 V or 10-30 V DC by board
- Sensors
- R502, R503, R558 capacitive modules
- USB readers
- USB 5 V, Windows SDK; optical or capacitive
- Terminal
- X05 with fingerprint, RFID, cameras and Wi-Fi
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Grow K202 Fingerprint Control Board – 12V DC, 120 Fingerprint Capacity, Relay Output₹909
Option 2Grow K215 Fingerprint Control Board – 10-30V DC, 200 Fingerprint Capacity, Relay Output₹1,149
Option 3Grow K219-A Fingerprint Control Board – 12V DC, 120 Fingerprint Capacity, Relay Output₹1,199
Option 4Grow K220 Fingerprint Control Board – 200 Fingerprint Capacity, Dual 10A Relay Outputs, DC 10-24V₹1,389
Option 5Grow KL216 Fingerprint Control Board – Aluminum Housing, 10A Relay Output, 200 Fingerprint Capacity₹1,049
Option 6Grow KL261+R558-S Fingerprint Control Board – 5.5-15V DC, 10A Relay Output₹2,219
What the Fingerprint access control boards and USB fingerprint readers: Grow K and KS boards, R101 to R105 USB readers, HF4000 and X05 terminal is
Fingerprint access control boards and USB readers capture and match fingerprints for door locks, attendance systems and PC logins, using modules like the R307, AS608 or standalone controllers.
Power the board from the supply range on its label and wire the lock through the relay: supply positive to COM, lock to NO for a fail-secure lock or NC for a fail-safe magnetic lock. Put a flyback diode across a solenoid lock.
The first finger enrolled usually becomes the admin. Follow the board's leaflet for the button sequence to add and delete users, and enrol each user's finger two or three times at different angles for reliable matching. For USB readers, install the maker's SDK or demo software; they are not plug-and-play Windows Hello devices unless stated.
Fingerprint access control boards and USB fingerprint readers: Grow K and KS boards, R101 to R105 USB readers, HF4000 and X05 terminal pinout
The pins on the Fingerprint access control boards and USB fingerprint readers: Grow K and KS boards, R101 to R105 USB readers, HF4000 and X05 terminal and what each one does.
| Pin | Function |
|---|---|
| V+ / GND | Board supply |
| COM / NO / NC | Relay contacts for the lock |
| Sensor connector | To the R50x fingerprint module |
| Exit button | Opens the lock from inside on some boards |
| Buzzer / LED | Status feedback |
| USB | PC connection on readers |
- V+ / GND
- Board supply
- COM / NO / NC
- Relay contacts for the lock
- Sensor connector
- To the R50x fingerprint module
- Exit button
- Opens the lock from inside on some boards
- Buzzer / LED
- Status feedback
- USB
- PC connection on readers
Wiring the Fingerprint access control boards and USB fingerprint readers: Grow K and KS boards, R101 to R105 USB readers, HF4000 and X05 terminal
Keep a mechanical override or key for doors; a power cut or dead board must not lock people in or out.
| Fingerprint access control boards and USB fingerprint readers: Grow K and KS boards, R101 to R105 USB readers, HF4000 and X05 terminal pin | Connection | Note |
|---|---|---|
| 12 V supply | Board V+ and GND | Check the board's range |
| Lock | Relay NO (fail-secure) or NC (magnetic) | Diode across solenoid |
| Sensor | Board connector | Fixed cable, check orientation |
| Exit button | Board input | Optional |
- 12 V supply
- Connection:
- Board V+ and GND
- Note:
- Check the board's range
- Lock
- Connection:
- Relay NO (fail-secure) or NC (magnetic)
- Note:
- Diode across solenoid
- Sensor
- Connection:
- Board connector
- Note:
- Fixed cable, check orientation
- Exit button
- Connection:
- Board input
- Note:
- Optional
Example code
Sequences differ between board models; the leaflet for your board is the authority.
1. Power the board; the sensor ring lights.
2. Place the first finger 3 times when prompted: it becomes the admin finger.
3. To add a user: admin finger, then the new finger 3 times.
4. To delete all users: hold the board's SET or CLR button as the leaflet shows.
5. Test: an enrolled finger clicks the relay for the set unlock time.
6. Adjust unlock time (where the board allows) with the jumper or button sequence.Setup and tuning
wire TX and RX to the microcontroller at 3.3 or 5 V as rated and use the Adafruit Fingerprint library.
run the enroll example to store each finger with an ID.
switch the lock through a relay or MOSFET with a flyback diode; never from a GPIO pin.
add an admin finger first, then users, using the board buttons.
install the vendor SDK or Windows Hello driver.
What you need
Shop this list16 of 16 found in our store · ₹65,851
Grow K202 Fingerprint Control Board – 12V DC, 120 Fingerprint Capacity, Relay Output: the part this guide coversGrow K202 Fingerprint Control Board – 12V DC, 120 Fingerprint Capacity, Relay Output₹909
Grow K215 Fingerprint Control Board – 10-30V DC, 200 Fingerprint Capacity, Relay Output: another version this guide coversGrow K215 Fingerprint Control Board – 10-30V DC, 200 Fingerprint Capacity, Relay Output₹1,149
Grow K219-A Fingerprint Control Board – 12V DC, 120 Fingerprint Capacity, Relay Output: another version this guide coversGrow K219-A Fingerprint Control Board – 12V DC, 120 Fingerprint Capacity, Relay Output₹1,199
Grow K220 Fingerprint Control Board – 200 Fingerprint Capacity, Dual 10A Relay Outputs, DC 10-24V: another version this guide coversGrow K220 Fingerprint Control Board – 200 Fingerprint Capacity, Dual 10A Relay Outputs, DC 10-24V₹1,389
Grow KL216 Fingerprint Control Board – Aluminum Housing, 10A Relay Output, 200 Fingerprint Capacity: another version this guide coversGrow KL216 Fingerprint Control Board – Aluminum Housing, 10A Relay Output, 200 Fingerprint Capacity₹1,049
Grow KL261+R558-S Fingerprint Control Board – 5.5-15V DC, 10A Relay Output: another version this guide coversGrow KL261+R558-S Fingerprint Control Board – 5.5-15V DC, 10A Relay Output₹2,219
Grow KR501 Fingerprint Control Board – 20 Fingerprint Capacity, 3.7-10V DC: another version this guide coversGrow KR501 Fingerprint Control Board – 20 Fingerprint Capacity, 3.7-10V DC₹1,019
Grow KS200 Fingerprint Control Board – Compatible with R502-A/R503 Modules: another version this guide coversGrow KS200 Fingerprint Control Board – Compatible with R502-A/R503 Modules₹589
Grow KS220-L Fingerprint Control Board: another version this guide coversGrow KS220-L Fingerprint Control Board₹655
Grow R101 Fingerprint Reader – USB 5V, 1000 Fingerprint Capacity: another version this guide coversGrow R101 Fingerprint Reader – USB 5V, 1000 Fingerprint Capacity₹4,449
Grow R101S Fingerprint Reader – USB Interface, Zinc Alloy Housing: another version this guide coversGrow R101S Fingerprint Reader – USB Interface, Zinc Alloy Housing₹4,269
Grow R102 Fingerprint Reader – USB Interface, Zinc Alloy Housing: another version this guide coversGrow R102 Fingerprint Reader – USB Interface, Zinc Alloy Housing₹3,069
Grow R105 USB Capacitive Fingerprint Reader – Zinc Alloy Housing: another version this guide coversGrow R105 USB Capacitive Fingerprint Reader – Zinc Alloy Housing₹3,729
HFSecurity HF4000 Optical Fingerprint Scanner – 500 DPI, USB Type-A/Micro USB: another version this guide coversHFSecurity HF4000 Optical Fingerprint Scanner – 500 DPI, USB Type-A/Micro USB₹5,329
HFSecurity X05 Biometric Access Control Device – Fingerprint & RFID, Dual Cameras, Wi-Fi/Bluetooth, POE/LAN: another version this guide coversHFSecurity X05 Biometric Access Control Device – Fingerprint & RFID, Dual Cameras, Wi-Fi/Bluetooth, POE/LAN₹33,129
Generic R503 DC12V Low Power Consumption Ring Fingerprint Access Control Board – STM8 Processor: another version this guide coversR503 DC12V Low Power Consumption Ring Fingerprint Access Control Board – STM8 Processor₹1,700
Alternatives and when to choose them
- Fingerprint sensors: R307, R503 and AS608 with Arduino.
- Solenoid door lock: the lock to drive.
- Smart fingerprint locks: ready-made locks.
Common mistakes to avoid
- Driving a lock solenoid straight from a GPIO pin.
- Leaving out the flyback diode on the lock.
- Not setting an admin finger on standalone boards.
- Using the wrong baud rate.
Frequently asked questions
How many fingerprints can the module store?
Most hold 120 to 1000 templates, depending on the model.
Why does the module not respond?
TX and RX are swapped or the baud rate is wrong; the default is 57600.
Can I unlock a door with it?
Yes. Match the finger, then switch a lock relay or MOSFET.
Does it work with wet or dirty fingers?
Matching gets worse; clean the sensor and enrol each finger twice.
Can I use a USB reader with Windows Hello?
Only readers with Windows Hello drivers work for login.
Parts for this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
