LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsThe R307 stores fingerprints inside itself, so the Uno only asks "is this a known finger?" and gets back an ID number. A match lights green and pulls the solenoid lock for four seconds; anything else gets three short beeps. Up to 1,000 fingers can be enrolled.
Keep to low-voltage loads unless a qualified electrician wires the mains side in an earthed, closed enclosure.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Optical fingerprint scanner that stores up to 1,000 prints in its own memory and reports a match over serial.
An electrically isolated switch that lets a 3.3/5 V pin turn a 12 V (or mains) load on and off.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Green indicator LED for the normal state.; Red indicator LED for the alert state.
1 kΩ + 2 kΩ divider for the 3.3 V input; 220 Ω series resistor for each LED
Follow the colours: red is power, dark grey is ground, blue is a signal.
fingerprint_door_lock.inoVerify & upload in Electrolark// Fingerprint door lock
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "fingerprint-door-lock"
#include <Adafruit_Fingerprint.h>
#include <SoftwareSerial.h>
// ---- pins ----
const uint8_t FP_RX = 2;
const uint8_t FP_TX = 3;
const uint8_t RELAY_PIN = 4;
const uint8_t BUZZER_PIN = 5;
const uint8_t LED_GREEN = 6;
const uint8_t LED_RED = 7;
const bool RELAY_ACTIVE_LOW = true; // most relay modules switch on when IN is LOW
SoftwareSerial fpSerial(FP_RX, FP_TX);
Adafruit_Fingerprint finger(&fpSerial);
const unsigned long UNLOCK_MS = 4000; // how long the lock stays open
void setRelay(bool on) { digitalWrite(RELAY_PIN, (on != RELAY_ACTIVE_LOW) ? HIGH : LOW); }
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void setGreenLed(bool on) { digitalWrite(LED_GREEN, on ? HIGH : LOW); }
void setRedLed(bool on) { digitalWrite(LED_RED, on ? HIGH : LOW); }
// returns the stored ID of a matching finger, or -1
int matchFinger() {
if (finger.getImage() != FINGERPRINT_OK) return -1;
if (finger.image2Tz() != FINGERPRINT_OK) return -1;
if (finger.fingerSearch() != FINGERPRINT_OK) return -1;
return finger.fingerID;
}
void unlock(int id) {
Serial.print(F("Welcome, ID ")); Serial.print(id); Serial.print(F(" (confidence ")); Serial.print(finger.confidence); Serial.println(F(")"));
setRelay(true); setGreenLed(true); setRedLed(false);
setBuzzer(true); delay(80); setBuzzer(false);
delay(UNLOCK_MS);
setRelay(false); setGreenLed(false); setRedLed(true);
}
void reject() {
Serial.println(F("No match"));
for (int i = 0; i < 3; i++) { setBuzzer(true); delay(60); setBuzzer(false); delay(60); }
delay(800);
}
void setup() {
Serial.begin(115200);
pinMode(RELAY_PIN, OUTPUT);
setRelay(false);
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
pinMode(LED_GREEN, OUTPUT);
pinMode(LED_RED, OUTPUT);
fpSerial.begin(57600);
finger.begin(57600);
if (finger.verifyPassword()) Serial.println(F("Fingerprint sensor ready"));
else Serial.println(F("Fingerprint sensor not found"));
setRelay(false); setGreenLed(false); setRedLed(true);
}
void loop() {
int id = matchFinger();
if (id >= 0) unlock(id);
else if (finger.getImage() == FINGERPRINT_OK) reject(); // a finger was present but did not match
delay(50);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
TX/RX are crossed: sensor TX to the board RX pin in the sketch. Check the 3.3 V/5 V wire colours against the datasheet, they vary between batches.
Enrol the same finger twice and press flat on the glass; dry fingers match poorly, breathe on them.
Load must be on COM and NO, with its own supply in series.
Your module may be active-HIGH. Set RELAY_ACTIVE_LOW to false.
Some 5 V relay boards do not fully switch off with 3.3 V logic. Remove the JD-VCC jumper, feed JD-VCC from 5 V and VCC from 3.3 V, or use a relay board made for 3.3 V input.
Low-triggered module: invert the logic in setBuzzer().
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
The relay is rated for mains, but mains wiring is dangerous. Keep this build on low-voltage loads (12 V pumps, fans, LED strips), or have a qualified electrician fit the relay inside an earthed, closed enclosure.
Use a 5 V USB phone charger or a power bank into the board's USB port. Loads such as pumps, fans and solenoids need their own supply.
11 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, R307S Optical Fingerprint Reader Module – TTL UART, 5V Relay Module with Optocoupler (1 channel), Active Buzzer Module 3.3–5V, 2 × Through-Hole LED Pack (Pack of 10), Resistor Assortment Kit (30 Values), 12V Electric Solenoid Door / Cabinet Lock, DC Power Adapter 12V 2A (5.5x2.1mm), Solderless Breadboard (830 points), plus 1 more. Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2–3 hours. The build on this page has 12 steps.
No. This page has the complete, tested code (fingerprint_door_lock.ino). Install these libraries first: Adafruit Fingerprint Sensor Library and Adafruit Fingerprint Sensor Library.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,976 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Current-limiting resistors for LEDs; Isolation, relays and switching higher-power loads; Serial sensors with their own protocol.
Ideas that reuse this build: RFID card version and Keypad PIN version. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Fingerprint sensor not found Welcome, ID 0 (confidence -inf)
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.