Component guide · Intermediate · 5 min read
Low-Cost FPGA Boards

Sipeed Tang Nano 1K, 4K, 9K and 20K, Tang Primer 20K and 25K, iCESugar, iCESugar-Pro, Colorlight i9, OrangeCrab ECP5, VSDSquadron FM, Lattice CrossLink-NX, ECP5 and XP2 Eval Boards, Altera Cyclone II and IV Boards, DE0-Nano, LilyGO T-FPGA, Vicharak Shrike and QuickLogic Thing Plus
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
These are the most affordable ways to learn FPGAs. Sipeed Tang Nano and Primer boards use Gowin chips with Gowin EDA or open-source tools, and the 9K and 20K drive HDMI displays. iCESugar and VSDSquadron use Lattice iCE40, fully supported by the open-source yosys and nextpnr flow. ECP5 boards (OrangeCrab, Colorlight i9, iCESugar-Pro) run RISC-V soft CPUs with LiteX. Cyclone II and IV boards use Intel Quartus.
Key specs at a glance
- Families
- Gowin GW1N/GW2A/GW5A, Lattice iCE40, ECP5, CrossLink-NX, XP2, Intel Cyclone II/IV
- Logic
- 1K to 85K LUTs
- Tools
- Gowin EDA, Lattice Radiant/Diamond, Quartus, or yosys + nextpnr (iCE40, ECP5, Gowin)
- Programming
- On-board USB (BL702, FTDI or CH552) or USB-Blaster
- Extras
- HDMI, camera, SDRAM, ESP32-S3 combos (T-FPGA, ShrikeFi)
- Logic level
- 3.3V I/O
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Altera Cyclone II EP2C5T144 FPGA Development Board₹2,746
Option 2Altera Cyclone IV EP4CE10 FPGA Development Board₹5,416
Option 3EP4CE6E22 FPGA Core Development Board (Cyclone IV)₹1,279
Option 4Terasic DE0-Nano Dev Kit, Altera Cyclone IV FPGA, 32MB SDRAM₹16,879
Option 5Lattice CrossLink-NX LIFCL-40-EVN FPGA Evaluation Board₹17,989
Option 6Lattice ECP5 VERSA LFE5UM-45F FPGA Development Board₹35,419
What the Gowin Tang Nano, Lattice iCE40 and ECP5, and Altera Cyclone FPGA boards is
Gowin, Lattice and Altera FPGA boards such as the Tang Nano, iCEBreaker and DE10-Lite let you build custom digital logic in Verilog or VHDL, from blinking LEDs to soft CPUs.
Start with a Tang Nano 9K or iCESugar for blinking LEDs, UART and VGA/HDMI demos. Use ECP5 boards with LiteX to build a RISC-V system that runs Linux. Pick a Cyclone IV board or DE0-Nano if your course uses Quartus. ESP32 plus FPGA boards (LilyGO T-FPGA, Vicharak ShrikeFi) let a microcontroller load and talk to the FPGA over SPI.
The open-source flow (OSS CAD Suite) installs in minutes and builds small designs in seconds, which makes learning faster than with large vendor tools.
Gowin Tang Nano, Lattice iCE40 and ECP5, and Altera Cyclone FPGA boards pinout
The pins on the Gowin Tang Nano, Lattice iCE40 and ECP5, and Altera Cyclone FPGA boards and what each one does.
| Pin | Function |
|---|---|
| USB | Power, programming, UART |
| Clock | 12-50MHz oscillator |
| GPIO headers | 3.3V I/O |
| HDMI / camera | On Tang Nano 4K, 9K, 20K |
| Pmod | On iCESugar, Tang Primer dock |
- USB
- Power, programming, UART
- Clock
- 12-50MHz oscillator
- GPIO headers
- 3.3V I/O
- HDMI / camera
- On Tang Nano 4K, 9K, 20K
- Pmod
- On iCESugar, Tang Primer dock
Wiring the Gowin Tang Nano, Lattice iCE40 and ECP5, and Altera Cyclone FPGA boards
iCESugar appears as a USB drive: drag the .bin file onto it to program.
| Gowin Tang Nano, Lattice iCE40 and ECP5, and Altera Cyclone FPGA boards pin | Connection | Note |
|---|---|---|
| USB | PC | openFPGALoader or vendor tool |
| Pmod | Pmod module | 3.3V |
| HDMI | Monitor | Tang Nano 9K/20K demos |
- USB
- Connection:
- PC
- Note:
- openFPGALoader or vendor tool
- Pmod
- Connection:
- Pmod module
- Note:
- 3.3V
- HDMI
- Connection:
- Monitor
- Note:
- Tang Nano 9K/20K demos
Example code
Use the board's PCF or CST constraints file. For Gowin boards use nextpnr-himbaechel or Gowin EDA; for Cyclone use Quartus.
# yosys + nextpnr + icepack (OSS CAD Suite)
yosys -p "synth_ice40 -top blink -json blink.json" blink.v
nextpnr-ice40 --up5k --package sg48 --json blink.json --pcf board.pcf --asc blink.asc
icepack blink.asc blink.bin
# program: copy blink.bin to the iCESugar USB drive, or
openFPGALoader -b ice40_generic blink.binSetup and tuning
Gowin boards use the Gowin EDA; Lattice iCE40 and ECP5 work with open tools (Yosys, nextpnr); Altera uses Quartus Prime Lite.
set every pin in the constraints file to match the board schematic.
use the onboard oscillator pin and set its frequency in the timing constraints.
most banks run at 3.3 V or lower; never feed 5 V signals to FPGA pins.
blink an LED with a counter, then add buttons and a UART.
What you need
Shop this list20 of 20 found in our store · ₹1,54,464
Altera Cyclone II EP2C5T144 FPGA Development Board: the part this guide coversAltera Cyclone II EP2C5T144 FPGA Development Board₹2,746
Altera Cyclone IV EP4CE10 FPGA Development Board: another version this guide coversAltera Cyclone IV EP4CE10 FPGA Development Board₹5,416
EP4CE6E22 FPGA Core Development Board (Cyclone IV): another version this guide coversEP4CE6E22 FPGA Core Development Board (Cyclone IV)₹1,279
Terasic DE0-Nano Dev Kit, Altera Cyclone IV FPGA, 32MB SDRAM: another version this guide coversTerasic DE0-Nano Dev Kit, Altera Cyclone IV FPGA, 32MB SDRAM₹16,879
Lattice CrossLink-NX LIFCL-40-EVN FPGA Evaluation Board: another version this guide coversLattice CrossLink-NX LIFCL-40-EVN FPGA Evaluation Board₹17,989
Lattice ECP5 VERSA LFE5UM-45F FPGA Development Board: another version this guide coversLattice ECP5 VERSA LFE5UM-45F FPGA Development Board₹35,419
Lattice ECP5-5G LFE5UM5G-85F FPGA Evaluation Board: another version this guide coversLattice ECP5-5G LFE5UM5G-85F FPGA Evaluation Board₹14,869
LatticeXP2 Brevia2 LFXP2-5E-B2-EVN FPGA Dev Kit: another version this guide coversLatticeXP2 Brevia2 LFXP2-5E-B2-EVN FPGA Dev Kit₹13,429
LilyGO T-FPGA Dev Board – ESP32-S3 & Cyclone IV FPGA: another version this guide coversLilyGO T-FPGA Dev Board – ESP32-S3 & Cyclone IV FPGA₹3,149
MuseLAB Lattice ECP5 FPGA RISC-V Dev Board Colorlight i9: another version this guide coversMuseLAB Lattice ECP5 FPGA RISC-V Dev Board Colorlight i9₹4,929
MuseLAB PMOD-SDCARD Board for iCESugar FPGA: another version this guide coversMuseLAB PMOD-SDCARD Board for iCESugar FPGA₹259
MuseLAB iCESugar FPGA Board ICE40UP5k RISC-V Open Source: another version this guide coversMuseLAB iCESugar FPGA Board ICE40UP5k RISC-V Open Source₹4,839
MuseLAB iCESugar-Pro FPGA Board Lattice ECP5 RISC-V SODIMM: another version this guide coversMuseLAB iCESugar-Pro FPGA Board Lattice ECP5 RISC-V SODIMM₹6,769
OrangeCrab R0D2-25 ECP5 FPGA Development Board: another version this guide coversOrangeCrab R0D2-25 ECP5 FPGA Development Board₹12,419
Sipeed Lichee Tang Nano 4K FPGA Board w/ OV2640 Camera: another version this guide coversSipeed Lichee Tang Nano 4K FPGA Board w/ OV2640 Camera₹2,409
Sipeed Tang Nano 20K FPGA Development Board: another version this guide coversSipeed Tang Nano 20K FPGA Development Board₹3,829
Sipeed Tang Nano 9K FPGA Development Board (GW1NR-9): another version this guide coversSipeed Tang Nano 9K FPGA Development Board (GW1NR-9)₹2,039
Sipeed Tang Nano 1K FPGA Development Board (GW1NZ-LV1): another version this guide coversSipeed Tang Nano 1K FPGA Development Board (GW1NZ-LV1)₹979
Sipeed Tang Primer 20K FPGA Development Board: another version this guide coversSipeed Tang Primer 20K FPGA Development Board₹2,729
Sipeed Tang Primer 25K Core Board GW5A RISC-V FPGA: another version this guide coversSipeed Tang Primer 25K Core Board GW5A RISC-V FPGA₹2,089
Alternatives and when to choose them
- FPGA basics: fundamentals.
- Digilent and Numato Xilinx boards: Vivado boards.
- Alinx FPGA and Zynq boards: bigger Xilinx modules.
Common mistakes to avoid
- Leaving pins unconstrained so the tool picks random ones.
- Feeding 5 V logic into FPGA pins.
- Ignoring timing warnings.
- Using the wrong toolchain for the chip family.
Frequently asked questions
Which FPGA board is best for beginners?
A Tang Nano or iCEBreaker is cheap and well documented, with open-source tool support.
Do I need Verilog or VHDL?
Either works; Verilog is more common in hobby examples.
Why does my design not work on the board?
Check the pin constraints and clock frequency; wrong pins are the usual cause.
Can I connect 5 V sensors to an FPGA?
No. Use level shifters, because FPGA pins run at 3.3 V or less.
Can an FPGA run a CPU?
Yes. Soft cores like RISC-V or Nios II can run on mid-size FPGAs.
Parts for this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.








