Component guide · Advanced · 3 min read
HDMI to CSI-2 Bridges for Raspberry Pi

Blicube C790 and C792, Geekworm X1300 and X1301, and C779 TC358743 Boards
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
These boards use the Toshiba TC358743 chip to feed an HDMI signal into the Raspberry Pi's camera port, so the Pi can capture another computer's screen, a camera's HDMI output or a games console. They are the capture part of a PiKVM and are used for low-latency streaming. Capture tops out at 1080p25 to 1080p50 depending on lanes.
Key specs at a glance
- Chip
- Toshiba TC358743XBG
- Input
- HDMI up to 1080p
- Output
- MIPI CSI-2, 2 or 4 lanes
- Audio
- I2S on boards with audio pins (X1300-A2 adds it)
- Boards
- Pi 4, Pi 5, CM4, Zero 2 W (check cable)
- Uses
- PiKVM, HDMI streaming, recording
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Blicube HDMI to CSI-2 C790 for Raspberry Pi 5 & PiKVM₹2,645
Option 2Blicube C792 HDMI to CSI-2 Video Loopback Module₹2,729
Option 3Geekworm X1300 HDMI to CSI-2 Shield for Raspberry Pi 5₹3,799
Option 4Geekworm X1301 HDMI to CSI-2 Shield for Raspberry Pi 5/4B/3B+/3B₹4,559
Option 5Raspberry Pi HDMI to CSI-2 Adapter Board C779 with FFC Cable₹2,649
What the HDMI to CSI-2 bridge boards (TC358743) is
HDMI to CSI bridges such as the Toshiba TC358743 boards let a Raspberry Pi capture video from a camera, PC or console through its CSI camera port.
Add dtoverlay=tc358743 to config.txt and set an EDID so the source sends a supported resolution. On the Pi 5 use the 22-pin cable and the CAM port.
These are not general webcams: the source must output HDMI, and HDCP-protected content will not capture.
HDMI to CSI-2 bridge boards (TC358743) pinout
The pins on the HDMI to CSI-2 bridge boards (TC358743) and what each one does.
| Pin | Function |
|---|---|
| HDMI in | From the source computer or camera |
| CSI ribbon | 15 or 22-pin to the Pi CAM port |
| I2S audio | Optional, to GPIO 18-21 |
| Power | From the CSI ribbon |
- HDMI in
- From the source computer or camera
- CSI ribbon
- 15 or 22-pin to the Pi CAM port
- I2S audio
- Optional, to GPIO 18-21
- Power
- From the CSI ribbon
Wiring the HDMI to CSI-2 bridge boards (TC358743)
Power the Pi off before connecting the ribbon. The CSI cable carries power, so no extra wires are needed except for audio.
| HDMI to CSI-2 bridge boards (TC358743) pin | Connection | Note |
|---|---|---|
| CSI ribbon | CAM port (22-pin on Pi 5) | Contacts toward the pins |
| HDMI | Source HDMI out to board | 1080p50 or lower |
| Audio | I2S pins to GPIO (optional) | X1300-A2 for X1300 |
- CSI ribbon
- Connection:
- CAM port (22-pin on Pi 5)
- Note:
- Contacts toward the pins
- HDMI
- Connection:
- Source HDMI out to board
- Note:
- 1080p50 or lower
- Audio
- Connection:
- I2S pins to GPIO (optional)
- Note:
- X1300-A2 for X1300
Example code
PiKVM OS sets all of this up for you. The 1080P50EDID.txt example file is in the Raspberry Pi kernel documentation for tc358743.
echo "dtoverlay=tc358743" | sudo tee -a /boot/firmware/config.txt
sudo reboot
# Load an EDID so the source picks 1080p
v4l2-ctl --set-edid=file=1080P50EDID.txt
v4l2-ctl --query-dv-timings
v4l2-ctl --set-dv-bt-timings query
v4l2-ctl --stream-mmap --stream-count=100 --stream-to=capture.rawSetup and tuning
enable the tc358743 overlay in config.txt and update to a recent Raspberry Pi OS.
load an EDID file with v4l2-ctl so the source sends a supported mode.
the TC358743 handles up to 1080p at 25 or 30 fps over 2 lanes; 1080p60 needs a 4-lane CSI port such as the CM4 or Pi 5.
use the right CSI ribbon (15 or 22 pin) and insert it with the contacts the right way.
some boards also capture audio over I2S; wire and enable it separately.
What you need
Shop this list8 of 8 found in our store · ₹23,743
Blicube HDMI to CSI-2 C790 for Raspberry Pi 5 & PiKVM: the part this guide coversBlicube HDMI to CSI-2 C790 for Raspberry Pi 5 & PiKVM₹2,645
Blicube C792 HDMI to CSI-2 Video Loopback Module: another version this guide coversBlicube C792 HDMI to CSI-2 Video Loopback Module₹2,729
Geekworm X1300 HDMI to CSI-2 Shield for Raspberry Pi 5: another version this guide coversGeekworm X1300 HDMI to CSI-2 Shield for Raspberry Pi 5₹3,799
Geekworm X1301 HDMI to CSI-2 Shield for Raspberry Pi 5/4B/3B+/3B: another version this guide coversGeekworm X1301 HDMI to CSI-2 Shield for Raspberry Pi 5/4B/3B+/3B₹4,559
Raspberry Pi HDMI to CSI-2 Adapter Board C779 with FFC Cable: another version this guide coversRaspberry Pi HDMI to CSI-2 Adapter Board C779 with FFC Cable₹2,649
Raspberry Pi 4 Model B (4 GB): works with all 40-pin HATsRaspberry Pi 4 Model B 1GB RAM₹4,476Closest match, check the specs
Raspberry Pi 5 (4 GB): the board the HAT stacks onGeekworm Raspberry Pi 5 PoE HAT 802.3af/at (USB-C)₹2,659Closest match, check the specs
15-pin to 22-pin camera cable: for the Raspberry Pi 5Arducam CB008 3.8cm 15-Pin to 22-Pin Camera Cable for Raspberry Pi Zero/W₹227
Alternatives and when to choose them
- IP KVM: complete PiKVM builds.
- Pi camera adapters: cables and extensions.
- Pi audio HATs: audio output.
Common mistakes to avoid
- Forgetting to load the EDID.
- Expecting 1080p60 on a 2-lane port.
- Inserting the ribbon cable the wrong way.
- Trying to capture HDCP-protected sources.
Frequently asked questions
Can a Raspberry Pi capture HDMI video with this bridge?
Yes. With the TC358743 overlay the Pi sees it as a video device for GStreamer or ffmpeg.
Why do I get no signal?
The EDID is not loaded or the source is sending an unsupported resolution.
Can it capture 1080p at 60 fps?
Only on 4-lane CSI ports such as the CM4 or Pi 5; 2-lane ports reach about 30 fps.
Does it work with HDCP-protected sources?
No. Protected content such as streaming boxes will not show.
Does the bridge capture audio?
Some boards pass audio over I2S; it needs extra wiring and setup.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


