Component guide · Intermediate · 4 min read
Arducam Multi-Camera Adapter V2.2, 5MP and 8MP PTZ Cameras, IMX219 Extension

StereoPi v2, USB Shield Adapter and MT9 Sensors
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
These parts help when one plain camera is not enough. The Arducam multi-camera adapter switches up to four CSI cameras onto one Pi port; the PTZ cameras add motorized pan, tilt, zoom and focus controlled over I2C; the extension cable moves the sensor away from its board; StereoPi v2 runs two cameras on a Compute Module 4; and the MT9 sensors fit Arducam's USB camera shield.
Key specs at a glance
- Multi-camera
- Up to 4 cameras, one active at a time (V2.2)
- PTZ
- 5MP OV5647 or 8MP IMX219, pan, tilt, zoom, focus
- Control
- I2C for PTZ motors; GPIO for adapter selection
- StereoPi
- CM4 carrier with two CSI ports
- MT9J001 / MT9N001
- 10MP mono and 9MP colour for the USB shield
- Extension
- 300 mm sensor cable for IMX219
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Arducam Multi Camera Adapter Module V2.2 for Raspberry Pi IMX708/OV5647/IMX219/IMX477₹5,299
Option 2Arducam B01675MP 5MP 1080p Pan Tilt Zoom PTZ Camera for Raspberry Pi₹9,759
Option 3Arducam B01678MP 8MP PTZ Camera for Raspberry Pi & Jetson Nano₹10,919
Option 4Arducam B0186 IMX219 Sensor Extension Cable, 300mm₹1,439
Option 5StereoPi v2 Slim Camera Carrier Board for Raspberry Pi CM4₹5,459
Option 6Arducam Parallel Camera Adapter Board for USB Camera Shield₹1,419
What the Pi camera multiplexers, PTZ cameras and extensions is
Pi camera adapters and pan-tilt-zoom (PTZ) kits include CSI cable adapters, extension boards, multi-camera switches and servo pan-tilt mounts for Raspberry Pi cameras.
The multi-camera adapter switches cameras, it does not merge them: you capture from one, switch, then the next. For true simultaneous stereo use a Pi 5 (two ports), a CM4 carrier like StereoPi, or a stereo USB camera.
PTZ cameras need Arducam's Python scripts to drive the motors.
Pi camera multiplexers, PTZ cameras and extensions pinout
The pins on the Pi camera multiplexers, PTZ cameras and extensions and what each one does.
| Pin | Function |
|---|---|
| CSI ribbon (15 or 22-pin) | Camera data lanes, clock, I2C control and power in one flat cable |
| Metal contacts | Face the connector contacts; a reversed cable gives 'no cameras available' |
| Lens mount | Fixed, M12 or CS/C mount depending on the board |
| IR-CUT / focus motor | Driven over the same ribbon on boards that have them |
- CSI ribbon (15 or 22-pin)
- Camera data lanes, clock, I2C control and power in one flat cable
- Metal contacts
- Face the connector contacts; a reversed cable gives 'no cameras available'
- Lens mount
- Fixed, M12 or CS/C mount depending on the board
- IR-CUT / focus motor
- Driven over the same ribbon on boards that have them
Wiring the Pi camera multiplexers, PTZ cameras and extensions
Turn the Pi off before connecting. Lift the connector latch, push the ribbon fully in with the contacts facing the pins, then press the latch down. The Pi 5 and Zero use the smaller 22-pin connector. The multi-camera adapter also plugs onto the GPIO header for switching.
| Pi camera multiplexers, PTZ cameras and extensions pin | Raspberry Pi 5 | Raspberry Pi 4 |
|---|---|---|
| Ribbon cable | CAM/DISP 0 or 1 (22-pin, use a 15-to-22 cable) | CAMERA port (15-pin) |
| Power | From the ribbon (no extra wires) | From the ribbon (no extra wires) |
| Software | rpicam-apps / Picamera2 (Bookworm) | rpicam-apps / Picamera2 (Bookworm) |
- Ribbon cable
- Raspberry Pi 5:
- CAM/DISP 0 or 1 (22-pin, use a 15-to-22 cable)
- Raspberry Pi 4:
- CAMERA port (15-pin)
- Power
- Raspberry Pi 5:
- From the ribbon (no extra wires)
- Raspberry Pi 4:
- From the ribbon (no extra wires)
- Software
- Raspberry Pi 5:
- rpicam-apps / Picamera2 (Bookworm)
- Raspberry Pi 4:
- rpicam-apps / Picamera2 (Bookworm)
Example code
Run Arducam's PTZ or multi-camera example scripts to move motors or switch inputs, then capture as normal.
from picamera2 import Picamera2
from picamera2.encoders import H264Encoder
import time
cam = Picamera2()
cam.configure(cam.create_still_configuration())
cam.start()
time.sleep(2) # let exposure and white balance settle
cam.capture_file("ptz.jpg")
cam.stop()
video = cam.create_video_configuration(main={"size": (1920, 1080)})
cam.configure(video)
cam.start_recording(H264Encoder(10_000_000), "clip.h264")
time.sleep(10)
cam.stop_recording()Setup and tuning
Pi 5 and Pi Zero use a 22-pin camera connector; older Pi models use 15-pin, so use the right adapter cable.
long CSI runs need an HDMI-CSI extension kit, not a plain long ribbon.
Arducam multi-camera adapters switch between cameras; only one streams at a time on basic boards.
drive pan-tilt servos with a PWM HAT and a 5 V supply that can handle servo current.
use libcamera or Picamera2, and select the camera index if several are fitted.
What you need
Shop this list11 of 12 found in our store · ₹83,237
Arducam Multi Camera Adapter Module V2.2 for Raspberry Pi IMX708/OV5647/IMX219/IMX477: the part this guide coversArducam Multi Camera Adapter Module V2.2 for Raspberry Pi IMX708/OV5647/IMX219/IMX477₹5,299
Arducam B01675MP 5MP 1080p Pan Tilt Zoom PTZ Camera for Raspberry Pi: another version this guide coversArducam B01675MP 5MP 1080p Pan Tilt Zoom PTZ Camera for Raspberry Pi₹9,759
Arducam B01678MP 8MP PTZ Camera for Raspberry Pi & Jetson Nano: another version this guide coversArducam B01678MP 8MP PTZ Camera for Raspberry Pi & Jetson Nano₹10,919
Arducam B0186 IMX219 Sensor Extension Cable, 300mm: another version this guide coversArducam B0186 IMX219 Sensor Extension Cable, 300mm₹1,439
StereoPi v2 Slim Camera Carrier Board for Raspberry Pi CM4: another version this guide coversStereoPi v2 Slim Camera Carrier Board for Raspberry Pi CM4₹5,459
Arducam Parallel Camera Adapter Board for USB Camera Shield: another version this guide coversArducam Parallel Camera Adapter Board for USB Camera Shield₹1,419
Arducam B0096 MT9J001 1/2.3-Inch 10MP Monochrome Camera Module: another version this guide coversArducam B0096 MT9J001 1/2.3-Inch 10MP Monochrome Camera Module₹4,729
Arducam B0098 MT9N001 1/2.3-Inch 9MP Color Camera Module: another version this guide coversArducam B0098 MT9N001 1/2.3-Inch 9MP Color Camera Module₹3,342
Raspberry Pi 5 (4 GB): the computer the camera plugs intoRaspberry Pi 5 16GB RAM Single Board Computer₹36,169Closest match, check the specs
Raspberry Pi 4 Model B (4 GB): works with the standard 15-pin cableRaspberry Pi 4 Model B 1GB RAM₹4,476Closest match, check the specs
15-pin to 22-pin camera cable: for Raspberry Pi 5 and Zero boardsArducam CB008 3.8cm 15-Pin to 22-Pin Camera Cable for Raspberry Pi Zero/W₹227- Camera ribbon extension cable set: to mount the camera away from the boardFind this part
Alternatives and when to choose them
- Depth cameras: ready stereo depth.
- Pan-tilt kits: Pi camera basics.
- USB cameras: plug in many at once.
Common mistakes to avoid
- Using a 15-pin cable on a 22-pin port without an adapter.
- Powering servos from the Pi 5 V pin.
- Running a very long plain ribbon.
- Inserting the cable backwards.
Frequently asked questions
Which cable do I need for a Pi 5 camera?
A 22-pin to 15-pin cable for standard Pi cameras, or 22-to-22 for Pi Zero style cameras.
Can I extend the camera cable far?
Use an HDMI-CSI extension kit for several metres; long ribbons cause errors.
Can I use two cameras on one Pi?
Pi 5 and CM4 have two ports; other Pis need a multi-camera adapter.
How do I control a pan-tilt mount?
Use a servo HAT or PCA9685 board with Python, powered from a separate 5 V supply.
Why does the camera not appear?
The cable is reversed or the wrong type; check the contacts face the right way.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.



