Component guide · Intermediate · 3 min read
High-Power Boost Converters (150W 10A and XL6019 5A)

Setup and Limits
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
High-power boost converters raise a lower DC voltage to a higher one, such as 12 V to 19 or 24 V. The 150 W module and the XL6019 board handle far more power than an MT3608 or XL6009. The key limit is input current: a boost draws more current from its input than it delivers at the output, so size the supply and wires for that.
Key specs at a glance
- Input
- About 10 to 32 V (150 W), 5 to 40 V (XL6019)
- Output
- Up to about 35 to 46 V, always above input
- Input current
- Up to 10 A (150 W), 5 A (XL6019)
- Power
- 150 W board; XL6019 about 50 to 60 W
- Efficiency
- About 90 percent
- Note
- Output never goes below input
This part can carry many amps. Use wire thick enough for the current, put a fuse close to the battery, check that connectors are rated for the load and give drivers and motors room to cool. A short at these currents melts wires in seconds.
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1High-Power Boost Converter₹139
Option 2XL6019 Adjustable Boost Converter 5A₹104
What the High-power boost converter is
A boost converter raises a DC voltage: it stores energy in an inductor and releases it at a higher voltage. These high-power boards do it at 50 to 150 W, far more than small MT3608 modules.
Input current is about output power divided by input voltage, plus losses. Boosting 12 V to 24 V at 4 A pulls over 8 A from the 12 V side.
A boost converter has a direct path from input to output through its diode, so with no switching the output equals the input minus a diode drop. It cannot turn the load fully off.
High-power boost converter pinout
The pins on the High-power boost converter and what each one does.
| Pin | Function |
|---|---|
| IN+ / IN- | Low-voltage input |
| OUT+ / OUT- | High-voltage output |
| Trimmer | Output voltage |
- IN+ / IN-
- Low-voltage input
- OUT+ / OUT-
- High-voltage output
- Trimmer
- Output voltage
Wiring the High-power boost converter
Set the output with a multimeter before connecting any load. Turn the trimmer slowly; many need 10 or more turns before the voltage moves.
| High-power boost converter pin | Battery input | Supply input |
|---|---|---|
| IN | 12 V battery or supply | Same |
| OUT | 24 V load | Same |
- IN
- Battery input:
- 12 V battery or supply
- Supply input:
- Same
- OUT
- Battery input:
- 24 V load
- Supply input:
- Same
Example code
A minimal sketch to check the part works.
1. Power the module with nothing on the output.
2. Measure OUT+ to OUT- with a multimeter.
3. Turn the trimmer until the reading is correct.
4. Connect the load and measure again under load.Setup and tuning
size the source and wires for the input current, which is higher than the output current (input current ≈ output power ÷ 0.9 ÷ input voltage).
set the output voltage with no load and a meter connected.
keep air moving over both heatsinks at high power.
a boost converter passes the input through when idle, so use a MOSFET or relay on the output for a true off.
fuse the input line close to the battery.
What you need
Shop this list6 of 6 found in our store · ₹1,030
High-Power Boost Converter: the part this guide coversHigh-Power Boost Converter₹139
XL6019 Adjustable Boost Converter 5A: another version this guide coversXL6019 Adjustable Boost Converter 5A₹104
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
SMPS power supply in metal enclosure (5/12/24 V): a bench input supplySMPS Power Supply, Metal Enclosure (5V / 12V / 24V)₹298Closest match, check the specs
INA219 current and power monitor module: to log voltage and current from the outputINA219 Current and Power Monitor Module₹249
XL6009 adjustable boost converter module: a common boost for up to about 2 AXL6009 Adjustable Boost Converter Module₹63
Alternatives and when to choose them
- XL6009 boost: up to about 2 A.
- MT3608 boost: small loads.
- Buck-boost converters: when input can be above or below output.
Common mistakes to avoid
- Using a supply that cannot deliver the high input current.
- Expecting the output to go below the input.
- Expecting the output to switch off when the converter is idle.
- Leaving the input unfused.
Frequently asked questions
Can I boost 12 V to 24 V at 5 A?
That is 120 W out and over 10 A in, which is at the limit of the 150 W board. Plan for about 3 to 4 A at 24 V instead.
Can the output be set below the input?
No. A boost converter's output is always at least the input voltage. Use a buck or buck-boost converter for that.
Can it charge a laptop from a car battery?
It is possible, but a proper car laptop adapter has the protections a laptop expects, so it is the safer choice.
Why does the boost converter get hot?
Most of the heat comes from the high input current flowing through the inductor, switch and diode.
Is there reverse polarity protection?
Usually none. Check the input wiring carefully or add a protection module.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
