Component guide · Beginner · 3 min read
Ideal Diode and Anti-Reverse Diode Modules (60A, SS56 10A)

Uses and Wiring
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Anti-reverse modules let current flow one way only. The dual SS56 module uses Schottky diodes with about 0.5 V drop; the 60 A ideal diode module uses a MOSFET controller so the drop is tiny and it stays cool at high current. Use them to stop a battery feeding back into a solar panel, to OR two supplies, or to protect against reversed connections.
Key specs at a glance
- SS56 module
- 60 V, 10 A, about 0.5 V drop
- Ideal diode
- Up to 60 A (with cooling), millivolt drop
- Voltage
- Up to about 60 V (check model)
- Use
- Reverse current blocking, supply OR-ing
- Heat
- Schottky: 0.5 V x current; ideal diode: very low
- Terminals
- Screw terminals IN and OUT
This part can carry many amps. Use wire thick enough for the current, put a fuse close to the battery, check that connectors are rated for the load and give drivers and motors room to cool. A short at these currents melts wires in seconds.
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Ideal Diode / Anti-Backflow Module₹218
Option 2Anti-Reverse Diode Module 60V 10A (Dual SS56)₹24
What the Ideal diode anti-reverse module is
An anti-reverse module is a one-way valve for current. It lets current flow from IN to OUT but blocks it the other way, using Schottky diodes or a MOSFET controlled as an 'ideal diode'.
A Schottky at 10 A drops 0.5 V and makes 5 W of heat. An ideal diode at the same current drops only tens of millivolts.
To combine two supplies, put one module on each; the higher voltage supplies the load and the other takes over if it fails.
Ideal diode anti-reverse module pinout
The pins on the Ideal diode anti-reverse module and what each one does.
| Pin | Function |
|---|---|
| IN+ / IN- | Source |
| OUT+ / OUT- | Load |
- IN+ / IN-
- Source
- OUT+ / OUT-
- Load
Wiring the Ideal diode anti-reverse module
Connect the Ideal diode anti-reverse module like this.
| Ideal diode anti-reverse module pin | Solar blocking | Dual supply OR-ing |
|---|---|---|
| IN | Solar panel + | Supply A and B, one module each |
| OUT | Charge controller or battery + | Common load + |
- IN
- Solar blocking:
- Solar panel +
- Dual supply OR-ing:
- Supply A and B, one module each
- OUT
- Solar blocking:
- Charge controller or battery +
- Dual supply OR-ing:
- Common load +
Example code
A minimal sketch to check the part works.
Check direction: current flows IN to OUT only.
Measure voltage drop under load to confirm.Setup and tuning
follow the IN and OUT marking; reversed, it blocks your supply.
a Schottky module loses about 0.5 V × current, so heatsink it above about 5 A.
the MOSFET version drops only millivolts and stays cool at high current.
when combining two supplies, keep a common ground; the higher voltage supply carries the load.
pick a module rated above the maximum current and voltage, with margin for surges.
What you need
Shop this list4 of 4 found in our store · ₹717
Ideal Diode / Anti-Backflow Module: the part this guide coversIdeal Diode / Anti-Backflow Module₹218
Anti-Reverse Diode Module 60V 10A (Dual SS56): another version this guide coversAnti-Reverse Diode Module 60V 10A (Dual SS56)₹24
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
SMPS power supply in metal enclosure (5/12/24 V): a bench input supplySMPS Power Supply, Metal Enclosure (5V / 12V / 24V)₹298Closest match, check the specs
Alternatives and when to choose them
- Diodes: basics.
- Solar power.
- Robot power planning.
Common mistakes to avoid
- Installing it backwards.
- Running the Schottky version at high current with no heatsink.
- Expecting it to limit current, which it does not.
- Choosing a module rated below the system voltage.
Frequently asked questions
Why choose an ideal diode instead of a normal diode?
It drops only millivolts instead of about 0.5 V, so it wastes far less power and stays cool at high current.
Does it protect against reverse polarity?
Yes. If the input is connected backwards, it blocks the current and protects the load.
Can it stop a battery draining into a solar panel at night?
Yes. That is a common use: it blocks current flowing back into the panel.
Can I combine two batteries with it?
Yes, for OR-ing, but they will not share the load evenly; the higher voltage battery supplies most of it.
How much voltage does it drop?
About 0.5 V for the Schottky module and only millivolts for the ideal diode module.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
