Component guide · Beginner · 3 min read
INA219 current sensor

Pinout, Wiring and Code
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The INA219 measures the current, voltage and power of a DC load up to 26 V over I2C. It is wired in series on the positive side of the load (high side) and reads the tiny voltage across a 0.1 ohm shunt resistor, giving about ±3.2 A range with roughly 0.8 mA resolution. Default I2C address is 0x40.
Key specs at a glance
- Bus voltage
- 0 to 26 V
- Current range
- ±3.2 A with the 0.1 Ω shunt (default gain)
- Resolution
- 12-bit ADC, about 0.8 mA per step at 3.2 A range
- Supply
- 3 to 5.5 V
- Interface
- I2C, address 0x40 (0x41, 0x44, 0x45 with solder jumpers)
- Accuracy
- About 1 percent over temperature (typical 0.5 percent)
A shorted, over-charged or damaged lithium cell can get very hot and catch fire. Use a protection board or BMS, never short the terminals, charge on a non-flammable surface and do not leave a charging pack alone. Throw away cells that are swollen or dented.
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1INA219 Current and Power Monitor Module₹249
Option 2Adafruit INA219 FeatherWing – High-Side Current Sensor₹719
What the INA219 current sensor is
The INA219 from Texas Instruments is a current shunt and power monitor. Current flows through a small resistor on the module; the chip measures the voltage drop across it and the voltage on the load side, then calculates current and power.
It is the easiest way to log how much power a battery project, solar panel or motor uses, and to estimate battery life from real numbers instead of datasheet guesses.
INA219 current sensor pinout
The pins on the INA219 current sensor and what each one does.
| Pin | Function |
|---|---|
| VCC | 3 to 5.5 V supply |
| GND | Ground (shared with the measured circuit) |
| SDA | I2C data |
| SCL | I2C clock |
| VIN+ | From the power supply + |
| VIN− | To the load + |
- VCC
- 3 to 5.5 V supply
- GND
- Ground (shared with the measured circuit)
- SDA
- I2C data
- SCL
- I2C clock
- VIN+
- From the power supply +
- VIN−
- To the load +
Wiring the INA219 current sensor
Break the positive wire to your load and put VIN+ and VIN− in that gap. The supply's negative must also connect to the INA219 GND, otherwise the bus voltage reads wrong.
| INA219 current sensor pin | Arduino Uno | ESP32 |
|---|---|---|
| VCC | 5V (or 3.3V) | 3V3 |
| GND | GND | GND |
| SDA | A4 | GPIO 21 |
| SCL | A5 | GPIO 22 |
| VIN+ | Supply + (up to 26 V) | Supply + (up to 26 V) |
| VIN− | Load + | Load + |
- VCC
- Arduino Uno:
- 5V (or 3.3V)
- ESP32:
- 3V3
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- SDA
- Arduino Uno:
- A4
- ESP32:
- GPIO 21
- SCL
- Arduino Uno:
- A5
- ESP32:
- GPIO 22
- VIN+
- Arduino Uno:
- Supply + (up to 26 V)
- ESP32:
- Supply + (up to 26 V)
- VIN−
- Arduino Uno:
- Load +
- ESP32:
- Load +
Example code
Install the Adafruit INA219 library. Use the 16 V / 400 mA calibration for small sensors or sleep current, where you need finer steps.
#include <Wire.h>
#include <Adafruit_INA219.h>
Adafruit_INA219 ina(0x40);
void setup() {
Serial.begin(115200);
if (!ina.begin()) { Serial.println("INA219 not found"); while (1); }
// ina.setCalibration_16V_400mA(); // finer resolution for small loads
}
void loop() {
float v = ina.getBusVoltage_V();
float i = ina.getCurrent_mA();
float p = ina.getPower_mW();
Serial.printf("%.2f V %.1f mA %.0f mW\n", v, i, p);
delay(1000);
}Setup and tuning
for currents above 3.2 A, replace the shunt with a smaller value (for example 0.01 Ω for about 32 A) and adjust calibration; the current shunt calculator helps.
set different addresses with the A0/A1 solder pads to monitor up to four rails.
average the current over a full duty cycle and use the battery life calculator.
negative readings mean current is flowing the other way, useful for charge and discharge logging.
What you need
Shop this list5 of 5 found in our store · ₹1,545
INA219 current and power monitor module: the common breakoutINA219 Current and Power Monitor Module₹249
Adafruit INA219 FeatherWing: for Feather boardsAdafruit INA219 FeatherWing – High-Side Current Sensor₹719Closest match, check the specs
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
0.96 inch OLED display 128x64: to show readings without a computer0.96" OLED Display 128x64₹139Closest match, check the specs
Dupont jumper wires: for the connectionsDupont Jumper Wires (40 pcs)₹49Closest match, check the specs
Alternatives and when to choose them
- ACS712: Hall-effect sensor, isolated, for 5 to 30 A, analog output, less precise at low current.
- Energy meters (PZEM): for AC mains power.
- Battery fuel gauges: track remaining charge directly.
Try it: Current shunt resistor calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Wiring the INA219 in parallel with the load instead of in series.
- No shared ground, so bus voltage reads 0 or random values.
- Measuring above 26 V, which damages the chip.
- Using the default 3.2 A range for a 10 mA load and getting coarse readings.
Frequently asked questions
Can the INA219 measure AC?
No. It is for DC only, up to 26 V.
What is the maximum current?
About 3.2 A with the standard 0.1 Ω shunt. Swap the shunt for higher ranges.
Does it work with 3.3 V boards?
Yes. Power it from 3.3 V and use the ESP32 I2C pins.
How do I use more than one?
Change the address with the A0 and A1 pads: 0x40, 0x41, 0x44 or 0x45.
High side or low side?
It is designed for the high side (positive wire), which keeps the load's ground intact.
INA219 or INA226?
The INA226 has a 16-bit ADC and 36 V range. For most hobby builds the INA219 is enough.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 33 step-by-step builds in our project library use parts from this guide.
Keep learning
Sources
- INA219 zero-drift bidirectional current/power monitor datasheet (Texas Instruments)
- Adafruit INA219 library
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
