Component guide · Intermediate · 3 min read
Inclinometers and Tilt Angle Sensors
Single and Dual Axis, 4-20 mA, RS485 and CAN
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
An inclinometer reports tilt angle, usually from a MEMS accelerometer. Choose the number of axes (single or dual), range (±90° or ±180°), accuracy and output (0-5 V, 4-20 mA, RS485 Modbus, CAN or TTL). Mount it rigidly, set the zero on a known level surface and filter out vibration. A bare accelerometer chip is cheaper but needs your own calibration.
Key specs at a glance
- Axes
- Single (±180°) or dual (±90°)
- Accuracy
- 0.1° to 0.2° typical for industrial parts
- Output
- 0-5 V, 4-20 mA, RS485 Modbus, CAN, TTL
- Supply
- 5 to 30 V depending on output
- Protection
- IP65 to IP67 housings
- Use
- Cranes, solar trackers, vehicles, structures
Output and axis choices
Pick the output your controller reads.
| Output | Good for | Notes |
|---|---|---|
| 0-5 V analog | Microcontroller ADCs | Short cables; use a stable supply |
| 4-20 mA | Industrial PLCs, long cables | Read with a shunt resistor; see current loops |
| RS485 Modbus | Many sensors on one bus | Set the address and baud; see Modbus |
| CAN | Vehicles and machines | See CAN bus |
| TTL serial | Direct to a microcontroller | Short wires only |
- 0-5 V analog
- Good for:
- Microcontroller ADCs
- Notes:
- Short cables; use a stable supply
- 4-20 mA
- Good for:
- Industrial PLCs, long cables
- Notes:
- Read with a shunt resistor; see current loops
- RS485 Modbus
- Good for:
- Many sensors on one bus
- Notes:
- Set the address and baud; see Modbus
- CAN
- Good for:
- Vehicles and machines
- Notes:
- See CAN bus
- TTL serial
- Good for:
- Direct to a microcontroller
- Notes:
- Short wires only
Single or dual axis
A single-axis ±180° inclinometer measures rotation about one axis, such as the angle of a boom. A dual-axis ±90° sensor measures tilt in two directions, such as the level of a platform. Check the datasheet for which axis is which and the direction of positive angle, then mark it on your enclosure.
Mounting and zeroing
- 1Fix the sensor to a rigid surface with flat contact; flex adds error.
- 2Align the arrow or axis marks with the direction you want to measure.
- 3Put the machine on a known level surface and send the zero command or read the offset.
- 4Keep it away from sources of heavy vibration, or enable the sensor's filter.
- 5Avoid mounting near strong magnets and note that temperature changes can shift readings slightly.
Inclinometer vs accelerometer chip
An accelerometer such as the MPU6050 or ADXL345 can also compute tilt, but it needs calibration, filtering and temperature compensation. Industrial inclinometers include these. Use a chip for hobby projects and a ready inclinometer where accuracy, protection or a 4-20 mA output matters; see MPU6050, accelerometers and vibration and tilt sensors.
Typical uses
- Solar tracker panels that follow the sun.
- Crane and boom angle monitoring.
- Levelling of platforms, antennas and drilling rigs.
- Slope monitoring on structures and landslide stations.
- Vehicle tilt warnings.
Try it: Angle converter calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Reading a 4-20 mA sensor without a shunt resistor.
- Mounting on a flexing plate.
- Skipping the zero calibration.
- Ignoring vibration and getting noisy readings.
- Confusing axis directions between two inclinometers.
Frequently asked questions
What accuracy do I need?
0.1° to 0.2° is common for industrial work. Hobby tilt switches are far coarser.
Can I use an inclinometer on a moving vehicle?
Acceleration adds error; use filtering or a sensor with gyro fusion.
Which output is best for long cables?
4-20 mA or RS485, since they resist noise.
What is the difference between ±90° and ±180°?
Dual-axis parts usually cover ±90°; single-axis parts can cover a full ±180°.
Do I need to calibrate?
Yes, set the zero after mounting.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.





