Component guide · Intermediate · 3 min read
Noise and Sound Level Sensors

DFRobot Gravity Analog Sound Level Meter (30-130 dBA), RS485 Modbus Noise Transmitters from Renke, FirstRate, JXBS and SN-300 Series with 4-20mA and 0-10V Outputs
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
A noise sensor reports sound level in decibels (dBA), weighted like human hearing, rather than just 'loud or quiet'. The DFRobot Gravity meter gives an analog voltage that maps straight to 30 to 130 dBA for Arduino projects. The wall-mount and long-rod transmitters are for factories, schools and roads: they read 30 to 120 dB and send it over RS485 Modbus or a 4-20mA loop to a PLC or logger.
Key specs at a glance
- Range
- 30 to 120 dB (transmitters), 30 to 130 dBA (DFRobot)
- Accuracy
- About ±0.5 to ±1.5 dB
- Weighting
- A-weighted
- Outputs
- RS485 Modbus RTU, 4-20mA, 0-10V or analog 0.6-2.6V
- Supply
- 9-30V DC (transmitters), 3.3-5V (DFRobot)
- Mount
- Wall box or long stainless rod
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1DFRobot Gravity Analog Sound Level Meter – A-Weighted 30-130dBA, 3.3-5V Input, Plug & Play₹5,039
Option 2FirstRate FST100-2010 Noise Sensor, 30dB~120dB, 20Hz~12.5kHz, RS485 Modbus, 9-30VDC₹8,159
Option 3JXBS-3001-ZS-RS-4 Industrial Noise Sensor Transmitter – RS485 Modbus & 4-20mA Output₹3,529
Option 4Renke RS-ZS-N01-2-EX Wall-mounted Noise Sensor 30-120dB ±0.5dB – RS485/4-20mA/0-10V Output₹6,249
Option 5Renke RS-ZS-N01-FL Industrial Noise Sensor 30dB~120dB ±0.5dB – RS485 Output₹7,179
Option 6SN-3002-ZS-N01 Wall Mount Noise Sensor – RS485 Output, ABS King Shell₹2,389
What the Noise and sound level sensors: RS485 Modbus noise transmitters and analog dBA meters is
Industrial noise sensors measure sound level in dB with a calibrated microphone and output RS485 Modbus or analog signals, used in factories, streets and noise monitoring.
For a classroom or a hobby noise meter, the DFRobot module is easiest: read the analog pin, convert to voltage and multiply by 50 to get dBA. For permanent sites, the RS485 versions give a stable calibrated reading that a PLC, Modbus gateway or Raspberry Pi can poll every second.
Mount the sensor away from walls that reflect sound and away from fans blowing across it. Cable runs over RS485 can be hundreds of metres with twisted pair and a 120 ohm terminator at the far end.
Noise and sound level sensors: RS485 Modbus noise transmitters and analog dBA meters pinout
The pins on the Noise and sound level sensors: RS485 Modbus noise transmitters and analog dBA meters and what each one does.
| Pin | Function |
|---|---|
| V+ / brown | 9-30V DC supply |
| V- / black | Supply ground |
| A+ / yellow | RS485 A |
| B- / blue | RS485 B |
| A (DFRobot) | Analog dBA voltage |
- V+ / brown
- 9-30V DC supply
- V- / black
- Supply ground
- A+ / yellow
- RS485 A
- B- / blue
- RS485 B
- A (DFRobot)
- Analog dBA voltage
Wiring the Noise and sound level sensors: RS485 Modbus noise transmitters and analog dBA meters
Check the colour code on your model's label; it varies between makers.
| Noise and sound level sensors: RS485 Modbus noise transmitters and analog dBA meters pin | Connection | Note |
|---|---|---|
| V+ and V- | 12V or 24V supply | Transmitters |
| A and B | USB-RS485 or MAX485 module | Default 4800 baud, address 1 on many |
| Analog out | Arduino A0 | DFRobot module |
| 4-20mA | PLC analog input | Current loop models |
- V+ and V-
- Connection:
- 12V or 24V supply
- Note:
- Transmitters
- A and B
- Connection:
- USB-RS485 or MAX485 module
- Note:
- Default 4800 baud, address 1 on many
- Analog out
- Connection:
- Arduino A0
- Note:
- DFRobot module
- 4-20mA
- Connection:
- PLC analog input
- Note:
- Current loop models
Example code
Register numbers, scale and baud rate differ between makers; confirm them in the sensor's Modbus table.
# pip install minimalmodbus
import minimalmodbus, time
s = minimalmodbus.Instrument('/dev/ttyUSB0', 1) # port, slave address
s.serial.baudrate = 4800 # check the manual
s.serial.timeout = 0.5
while True:
raw = s.read_register(0, 0, functioncode=3) # register 0 on many models
print('Noise:', raw / 10, 'dB') # value x10
time.sleep(1)Setup and tuning
feed the stated supply, often 10 to 30 V DC.
read RS485 Modbus registers or the 4 to 20 mA or 0 to 10 V output.
place at ear height, away from walls and direct wind.
check whether the sensor uses A-weighting (dBA), which matches human hearing.
use a windscreen or outdoor version for outside use.
What you need
Shop this list8 of 8 found in our store · ₹42,602
DFRobot Gravity Analog Sound Level Meter – A-Weighted 30-130dBA, 3.3-5V Input, Plug & Play: the part this guide coversDFRobot Gravity Analog Sound Level Meter – A-Weighted 30-130dBA, 3.3-5V Input, Plug & Play₹5,039
FirstRate FST100-2010 Noise Sensor, 30dB~120dB, 20Hz~12.5kHz, RS485 Modbus, 9-30VDC: another version this guide coversFirstRate FST100-2010 Noise Sensor, 30dB~120dB, 20Hz~12.5kHz, RS485 Modbus, 9-30VDC₹8,159
JXBS-3001-ZS-RS-4 Industrial Noise Sensor Transmitter – RS485 Modbus & 4-20mA Output: another version this guide coversJXBS-3001-ZS-RS-4 Industrial Noise Sensor Transmitter – RS485 Modbus & 4-20mA Output₹3,529
Renke RS-ZS-N01-2-EX Wall-mounted Noise Sensor 30-120dB ±0.5dB – RS485/4-20mA/0-10V Output: another version this guide coversRenke RS-ZS-N01-2-EX Wall-mounted Noise Sensor 30-120dB ±0.5dB – RS485/4-20mA/0-10V Output₹6,249
Renke RS-ZS-N01-FL Industrial Noise Sensor 30dB~120dB ±0.5dB – RS485 Output: another version this guide coversRenke RS-ZS-N01-FL Industrial Noise Sensor 30dB~120dB ±0.5dB – RS485 Output₹7,179
SN-3002-ZS-N01 Wall Mount Noise Sensor – RS485 Output, ABS King Shell: another version this guide coversSN-3002-ZS-N01 Wall Mount Noise Sensor – RS485 Output, ABS King Shell₹2,389
SN-300FL-ZS-N01 (485) Long Rod Noise Sensor – RS485 Modbus, 30-120 dB: another version this guide coversSN-300FL-ZS-N01 (485) Long Rod Noise Sensor – RS485 Modbus, 30-120 dB₹4,279
SN-300FL-ZS-N01 Long Rod Noise Sensor – RS485 Modbus & TTL, 316L Stainless Steel: another version this guide coversSN-300FL-ZS-N01 Long Rod Noise Sensor – RS485 Modbus & TTL, 316L Stainless Steel₹5,779
Alternatives and when to choose them
- Sound sensor modules: simple loud or quiet detection.
- RS485 and RS232: the bus these transmitters use.
- USB to RS485 converter: read Modbus from a PC.
Common mistakes to avoid
- Mounting it near a wall that reflects sound.
- Leaving out the windscreen outdoors.
- Using it for legal measurements.
- Feeding 10 V output into a 3.3 V pin.
Frequently asked questions
What does dBA mean?
A-weighted decibels, which match how humans hear loudness.
Can I read it with an Arduino?
Yes, through an RS485 module or an analog input with a divider.
Why are readings high outdoors?
Wind noise; add a windscreen.
Is it accurate enough for legal limits?
Only class 1 or class 2 certified meters are accepted.
What range do they measure?
Usually about 30 to 130 dB.
Parts for this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
