Buying guide · Intermediate · 3 min read
Laser Engravers and Desktop CNC Machines
A Starter Guide
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
Desktop diode laser engravers burn designs into wood, leather and card, and stronger ones cut thin plywood. Desktop CNC routers such as the CNC 3018 carve wood, plastics, PCBs and soft metals with a spinning bit. Both usually run GRBL firmware and take G-code from programs such as LightBurn, LaserGRBL or Candle. Choose by the optical laser power or spindle size, and plan for fume extraction, safety eyewear and an enclosure.
Key specs at a glance
- Diode laser power
- Optical output of about 5 to 20 W; ignore larger electrical input figures
- Laser materials
- Wood, leather, card, anodised aluminium marking; never PVC
- CNC 3018
- 300 x 180 mm work area, small 775 spindle, wood and plastic
- Firmware
- GRBL on most hobby controllers
- Software
- LightBurn, LaserGRBL (laser); Candle, UGS, Fusion CAM (CNC)
- Safety
- Wavelength-rated eyewear, ventilation, fire watch, enclosure
Diode laser engravers
Laser power is often advertised as electrical input; look for optical output. About 5 W engraves well; 10 to 20 W cuts 3 to 6 mm plywood in a few passes. Air assist (a small pump blowing at the cut) gives cleaner cuts and reduces flare-ups.
Never laser PVC, vinyl or anything containing chlorine, which gives off corrosive and toxic gas. Avoid polycarbonate and fibreglass. Blue diode lasers cannot cut clear acrylic, because the light passes straight through.
Wear eyewear rated for the laser's wavelength (often 445 to 455 nm), never leave a job running unattended, and keep a fire extinguisher nearby. Low-power laser modules are different devices entirely.
Desktop CNC routers
Small CNC machines like the 3018 are a good way to learn CAM and mill PCBs, wood and plastics. They are not rigid enough for steel, and aluminium needs light cuts with sharp bits.
- Hold the work firmly with clamps or double-sided tape.
- Set feeds and speeds for the bit and material; too slow burns, too fast snaps bits.
- Zero the tool on the workpiece and run a simulation before cutting.
- Bigger machines use lead or ball screws, stronger stepper drivers and larger spindles.
Fumes, dust and workspace
Both machines make fumes or dust. Vent laser smoke outside or through a proper filter, and use a dust shoe or vacuum on a CNC. Wear safety glasses and hearing protection for routers. Keep long hair and sleeves away from spinning tools, and add an emergency stop switch you can reach easily. Fit limit switches so the machine can home safely.
Try it: Stepper steps per mm calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Buying by electrical rather than optical laser power.
- Laser cutting PVC or vinyl.
- Running a laser unattended.
- Wearing eyewear not rated for the laser's wavelength.
- Expecting a CNC 3018 to cut steel.
Frequently asked questions
What can a 5 W diode laser cut?
It engraves most woods and leather and cuts thin card and balsa; plywood needs 10 W or more and several passes.
Can a diode laser cut acrylic?
Coloured and opaque acrylic, often yes. Clear acrylic, no, because blue light passes through it.
What is GRBL?
Open-source firmware that turns G-code into stepper and spindle motion on hobby machines.
Can a CNC 3018 cut aluminium?
Only with slow, shallow passes and sharp bits; it is designed for wood, plastics and PCBs.
Do I need an enclosure?
Strongly recommended for lasers to contain light and fumes, especially indoors.
Parts for this guide
Calculators
Terms in this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.




