Buying guide · Intermediate · 3 min read
Linear Rails, Lead Screws, Belts and Bearings for Machines
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
Most DIY machines use the same small set of motion parts. Smooth rods or linear rails guide each axis, a belt or lead screw moves it, a coupler joins the motor to the screw, and bearings support rotating parts. Belts are fast and suit 3D printers and laser engravers. Lead screws are slower but stronger and stay put when unpowered, which suits Z axes and CNC routers. Alignment matters more than part quality.
Key specs at a glance
- Guides
- 8 mm smooth rods with LM8UU bearings; MGN12 linear rails; V-slot wheels
- Lead screw
- T8 with 2 mm or 8 mm lead, brass or anti-backlash nut
- Belts
- GT2 6 mm or 10 mm, with 16 or 20 tooth pulleys
- Couplers
- 5 x 8 mm flexible or rigid for NEMA 17 to T8 screw
- Bearings
- 608 (8 mm bore), 624, KP08 and KFL08 pillow blocks
- Ball screws
- SFU1605 for CNC: low backlash, higher cost
Belts vs lead screws vs ball screws
| Drive | Speed | Force | Backlash | Typical use |
|---|---|---|---|---|
| GT2 belt | High | Low to medium | Low if tensioned | 3D printer X/Y, laser engraver |
| T8 lead screw | Low to medium | High | Some (anti-backlash nuts help) | 3D printer Z, small CNC |
| Ball screw | Medium to high | High | Very low | CNC routers and mills |
| Rack and pinion | High | Medium | Medium | Long axes, gates |
- GT2 belt
- Speed:
- High
- Force:
- Low to medium
- Backlash:
- Low if tensioned
- Typical use:
- 3D printer X/Y, laser engraver
- T8 lead screw
- Speed:
- Low to medium
- Force:
- High
- Backlash:
- Some (anti-backlash nuts help)
- Typical use:
- 3D printer Z, small CNC
- Ball screw
- Speed:
- Medium to high
- Force:
- High
- Backlash:
- Very low
- Typical use:
- CNC routers and mills
- Rack and pinion
- Speed:
- High
- Force:
- Medium
- Backlash:
- Medium
- Typical use:
- Long axes, gates
Rods, rails and wheels
cheap and simple; rods need support at both ends and flex over long lengths.
stiff and precise; need a flat mounting surface and occasional grease.
easy to build with, adjust wheel tension using eccentric nuts.
For steps per mm: a GT2 belt on a 20-tooth pulley moves 40 mm per revolution, so a 200-step motor at 16 microsteps gives 80 steps/mm. A T8 screw with 8 mm lead at the same settings gives 400 steps/mm. Use the stepper steps per mm calculator.
Assembly and alignment tips
- Keep rods or rails parallel; binding is the most common cause of skipped steps.
- Use a flexible coupler to absorb small misalignment between motor and screw, but do not use it to fix large errors.
- Do not constrain a lead screw at both the motor and a fixed bearing if they are not perfectly aligned; it causes wobble (Z-banding).
- Tension belts until they twang lightly; overtightening wears bearings.
- Tighten grub screws on a flat on the motor shaft, with thread-locker for vibration.
- See stepper motors and gear ratio for sizing.
Try it: Stepper steps per mm calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Rods or rails not parallel, causing binding.
- A rigid coupler on a misaligned lead screw.
- Belts too loose (backlash) or too tight (bearing wear).
- Grub screws loosening without a flat or thread-locker.
- Lead screws chosen for speed-critical axes.
Frequently asked questions
Belt or lead screw for my CNC?
Lead screws or ball screws for routers that cut; belts for fast, light machines such as laser engravers.
What does T8 2 mm vs 8 mm lead mean?
How far the nut moves per turn. 8 mm is faster; 2 mm gives more force and resolution.
Do I need linear rails?
Not always. Rods or V-slot are fine for many hobby machines; rails give stiffness and precision.
What is an anti-backlash nut?
A spring-loaded nut that removes play between the screw and nut.
How do I calculate steps per mm?
Motor steps × microsteps ÷ distance moved per revolution.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 2 step-by-step builds in our project library use parts from this guide.
Keep learning
Sources
- Gates GT2 belt drive design manual
- HIWIN linear guide technical information
- THK ball screw selection guide
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.




