Component guide · Beginner · 3 min read
12V Lifting Electromagnet (3 kg and Larger)

Holding Force, Wiring and Code
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
A lifting electromagnet is a coil inside a steel cup. When powered with 12 V, it holds flat steel parts with the rated force, such as 3 kg for the 20/15 size, and releases when power is cut. It is used as a robot gripper for steel parts, in crane models and for door holders. Rated force needs clean, flat, thick steel.
Key specs at a glance
- Voltage
- 12 V DC
- Holding force
- 3 kg (20/15) and larger sizes
- Current
- About 0.1 to 0.5 A depending on size
- Duty
- Continuous on most small units (gets warm)
- Mount
- Threaded centre hole
- Release
- Some residual magnetism
This part can carry many amps. Use wire thick enough for the current, put a fuse close to the battery, check that connectors are rated for the load and give drivers and motors room to cool. A short at these currents melts wires in seconds.
What the 12V lifting electromagnet is
A lifting electromagnet is a coil inside a steel cup. When powered it acts as a strong magnet on its flat face and holds steel parts; when power stops it lets them go.
Force drops sharply with any air gap, paint or thin sheet. Thin steel saturates and holds far less than rated.
Residual magnetism can hold light parts after switch-off; a brief reverse pulse with an H-bridge releases them cleanly.
12V lifting electromagnet pinout
The pins on the 12V lifting electromagnet and what each one does.
| Pin | Function |
|---|---|
| Red | +12 V |
| Black | Switched to ground |
- Red
- +12 V
- Black
- Switched to ground
Wiring the 12V lifting electromagnet
Connect the 12V lifting electromagnet like this.
| 12V lifting electromagnet pin | Arduino Uno | ESP32 |
|---|---|---|
| Load + | 12 V supply + | 12 V supply + |
| Load - | MOSFET module OUT- (or relay NO) | MOSFET module OUT- |
| Module signal | D7 | GPIO 26 |
| GND | GND (shared with 12 V -) | GND |
- Load +
- Arduino Uno:
- 12 V supply +
- ESP32:
- 12 V supply +
- Load -
- Arduino Uno:
- MOSFET module OUT- (or relay NO)
- ESP32:
- MOSFET module OUT-
- Module signal
- Arduino Uno:
- D7
- ESP32:
- GPIO 26
- GND
- Arduino Uno:
- GND (shared with 12 V -)
- ESP32:
- GND
Example code
A minimal sketch to check the part works.
const int MAG = 7;
void setup() { pinMode(MAG, OUTPUT); }
void loop() {
digitalWrite(MAG, HIGH); // pick
delay(4000);
digitalWrite(MAG, LOW); // drop
delay(4000);
}Setup and tuning
use flat, clean steel at least a few millimetres thick; paint, rust or gaps cut the holding force sharply.
use a MOSFET module or relay with a flyback diode across the coil.
if light parts stick after switch-off, give a short reverse pulse through an H-bridge.
keep it at 12 V; warm is normal, very hot means over-voltage.
use the threaded centre hole and keep the face clear of the frame.
What you need
Shop this list5 of 7 found in our store · ₹1,131
12V Lifting Electromagnet: the part this guide covers12V Lifting Electromagnet₹277- Uno R3 development board: the controller used in the wiring tableFind this part
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
MOSFET switch module (D4184 / LR7843): to switch or PWM it from a GPIOMOSFET Switch Module, Relay Replacement (D4184 / LR7843)₹39
L298N dual H-bridge motor driver module: to reverse itL298N Dual H-Bridge Motor Driver Module₹128- 1N4007 diode: flyback protection across the coil or motorFind this part
SMPS power supply in metal enclosure (5/12/24 V): a 12 V supplySMPS Power Supply, Metal Enclosure (5V / 12V / 24V)₹298Closest match, check the specs
Alternatives and when to choose them
- Solenoid door lock.
- Vacuum pumps: for non-magnetic parts.
- Linear actuators and solenoids.
Common mistakes to avoid
- Expecting the rated force on thin or painted steel.
- Switching it with no flyback diode.
- Running it above 12 V so it overheats.
- Using it to hold anything that would be dangerous if it dropped.
Frequently asked questions
Can an electromagnet lift aluminium?
No. It only holds ferrous metals such as mild steel and iron.
Can it stay on continuously?
Most small units can, and they get warm. Check the duty rating of yours.
Why does it hold less than the rated force?
The rating assumes thick, flat, clean steel with no gap. Thin sheet, paint or an air gap reduces force a lot.
How do I make parts release faster?
Give a brief reverse pulse with an H-bridge to cancel the leftover magnetism.
Can it lift a person or heavy loads safely?
No. Use it for robot grippers, models and door holders, never for lifting people or heavy loads overhead.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


