Component guide · Beginner · 3 min read
LV8729 Ultra-Quiet StepStick Stepper Driver

Microstepping, Vref and Wiring
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The LV8729 is a StepStick-format stepper driver that microsteps up to 1/128 for quiet, smooth motion. It fits A4988 and DRV8825 sockets on RAMPS and CNC shields, uses STEP and DIR control, and handles about 1.5 A per phase with cooling. Set current with the Vref pot before connecting the motor.
Key specs at a glance
- Format
- StepStick (A4988 footprint)
- Motor supply
- 6 to 36 V
- Current
- About 1.5 A per phase with heatsink
- Microstepping
- Up to 1/128 (M0 to M2)
- Control
- STEP, DIR, EN
- Logic
- 3.3 or 5 V
What the LV8729 stepper driver is
The LV8729 driver is a StepStick-sized module built on ON Semiconductor's LV8729 chip. It drops into the same sockets as A4988 and DRV8825 drivers and adds very fine microstepping for quieter motors.
The microstep pin table differs from the A4988, so jumper settings under the driver give different modes. Check the LV8729 table for your board.
Vref sets the current: on most boards I = Vref / (5 x Rs) with Rs about 0.22 ohm; check your board's formula.
LV8729 stepper driver pinout
The pins on the LV8729 stepper driver and what each one does.
| Pin | Function |
|---|---|
| VMOT / GND | Motor supply |
| 1A, 1B, 2A, 2B | Motor coils |
| STEP / DIR | Control |
| EN | Low = enabled |
| M0, M1, M2 | Microstep select |
| VDD | Logic supply |
- VMOT / GND
- Motor supply
- 1A, 1B, 2A, 2B
- Motor coils
- STEP / DIR
- Control
- EN
- Low = enabled
- M0, M1, M2
- Microstep select
- VDD
- Logic supply
Wiring the LV8729 stepper driver
Connect the LV8729 stepper driver like this.
| LV8729 stepper driver pin | Arduino Uno | ESP32 |
|---|---|---|
| STEP | D3 | GPIO 25 |
| DIR | D2 | GPIO 26 |
| EN | D8 (low to enable) | GPIO 27 |
| VDD / GND | 5V / GND | 3V3 / GND |
- STEP
- Arduino Uno:
- D3
- ESP32:
- GPIO 25
- DIR
- Arduino Uno:
- D2
- ESP32:
- GPIO 26
- EN
- Arduino Uno:
- D8 (low to enable)
- ESP32:
- GPIO 27
- VDD / GND
- Arduino Uno:
- 5V / GND
- ESP32:
- 3V3 / GND
Example code
At high microstepping the step rate must be high; use AccelStepper or a timer for real projects.
const int STEP = 3, DIR = 2;
void setup() { pinMode(STEP, OUTPUT); pinMode(DIR, OUTPUT); digitalWrite(DIR, HIGH); }
void loop() {
digitalWrite(STEP, HIGH); delayMicroseconds(50);
digitalWrite(STEP, LOW); delayMicroseconds(250);
}Setup and tuning
set it with the supply on and the motor unplugged. On most boards current ≈ Vref / (5 × Rs), with Rs about 0.22 Ω; check your board's sheet.
use the LV8729 table for M0 to M2. The A4988 jumper settings select different modes on this chip.
match the pot and the EN pin to the socket marking; a reversed driver is destroyed at power-up.
fit the heatsink and add airflow above about 1 A.
set steps per mm for the microstep you chose (for example 1/32 doubles the steps of 1/16).
What you need
Shop this list4 of 5 found in our store · ₹1,078
LV8729 Ultra-Quiet Stepper Driver (StepStick): the part this guide coversLV8729 Ultra-Quiet Stepper Driver (StepStick)₹639- Uno R3 development board: the controller used in the wiring tableFind this part
DRV8825 stepper driver with heatsink: a StepStick driver for small steppersDRV8825 Stepper Motor Driver with Heatsink₹92Closest match, check the specs
SMPS power supply in metal enclosure (5/12/24 V): a 12 or 24 V supplySMPS Power Supply, Metal Enclosure (5V / 12V / 24V)₹298Closest match, check the specs
Stepper motor mounting bracket: to mount the motorMotor Mounting Bracket₹49
Alternatives and when to choose them
- TMC2209: even quieter with StealthChop.
- DRV8825: common, 1/32.
- A4988 vs DRV8825 vs TMC2209.
Common mistakes to avoid
- Using the A4988 jumper table, so the driver runs at an unexpected microstep.
- Inserting it backwards in the socket.
- Running it without a heatsink at high current.
- Forgetting to update steps per mm after changing microstepping.
Frequently asked questions
Is the LV8729 quieter than the DRV8825?
Usually yes. Finer microstepping (up to 1/128) smooths the current steps, which reduces motor noise and vibration.
Does it fit RAMPS and CNC shield sockets?
Yes. It uses the StepStick pinout, but set its own microstep jumpers rather than copying A4988 settings.
What is the maximum microstepping?
1/128 step. Many printers and CNC controllers run it at 1/32 or 1/64 so the step rate stays within the controller's limits.
How do I set the motor current?
Measure Vref between the pot and GND and turn the pot until it matches the value for your motor's rated current.
What supply voltage does it take?
About 6 to 36 V. 12 V or 24 V is typical for 3D printers and small CNC machines.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


