Comparison · Intermediate · 4 min read
A4988 vs DRV8825 vs TMC2209
Which Stepper Driver?
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
All three are StepStick-size drivers controlled by STEP and DIR pins. The A4988 is cheap and fine up to about 1 A without cooling, with 1/16 microstepping. The DRV8825 handles higher voltage (up to 45 V) and 1/32 microstepping but its motors still whine. The TMC2209 is almost silent thanks to StealthChop, smoother at 1/256 interpolation, and supports sensorless homing over UART. For 3D printers and quiet machines, choose the TMC2209.
Key specs at a glance
- A4988
- 8 to 35 V, about 1 A (2 A with heatsink and airflow), up to 1/16 step
- DRV8825
- 8.2 to 45 V, about 1.5 A (2.2 A with cooling), up to 1/32 step
- TMC2209
- 4.75 to 29 V, 2 A RMS (2.8 A peak), up to 1/256 interpolated
- Control
- STEP, DIR, EN; TMC2209 adds single-wire UART
- Current set by
- Vref potentiometer (or UART on TMC2209)
- Footprint
- StepStick / Pololu 16-pin
Side by side
| A4988 | DRV8825 | TMC2209 | |
|---|---|---|---|
| Motor voltage | 8 to 35 V | 8.2 to 45 V | 4.75 to 29 V |
| Current per phase | About 1 A bare, 2 A with cooling | About 1.5 A bare, 2.2 A with cooling | 2 A RMS, 2.8 A peak |
| Microstepping | Full to 1/16 | Full to 1/32 | Up to 1/64 native, 1/256 interpolated |
| Noise | Audible whine and hum | Audible, sometimes worse at low speed | Near silent in StealthChop |
| Extras | Simple and cheap | Higher voltage | UART config, StallGuard sensorless homing, CoolStep |
| Best for | Learning, low-cost machines | Higher-voltage CNC | 3D printers, quiet or smooth motion |
- Motor voltage
- A4988:
- 8 to 35 V
- DRV8825:
- 8.2 to 45 V
- TMC2209:
- 4.75 to 29 V
- Current per phase
- A4988:
- About 1 A bare, 2 A with cooling
- DRV8825:
- About 1.5 A bare, 2.2 A with cooling
- TMC2209:
- 2 A RMS, 2.8 A peak
- Microstepping
- A4988:
- Full to 1/16
- DRV8825:
- Full to 1/32
- TMC2209:
- Up to 1/64 native, 1/256 interpolated
- Noise
- A4988:
- Audible whine and hum
- DRV8825:
- Audible, sometimes worse at low speed
- TMC2209:
- Near silent in StealthChop
- Extras
- A4988:
- Simple and cheap
- DRV8825:
- Higher voltage
- TMC2209:
- UART config, StallGuard sensorless homing, CoolStep
- Best for
- A4988:
- Learning, low-cost machines
- DRV8825:
- Higher-voltage CNC
- TMC2209:
- 3D printers, quiet or smooth motion
Setting the current limit with Vref
Every driver needs its current limit set to match the motor, or the motor overheats or skips steps. Measure the voltage between the trimmer and GND (Vref) with a multimeter while the board is powered, and turn the trimmer with a ceramic screwdriver.
I = Vref / (8 x Rs). Check the sense resistors: with R100 (0.1 Ω), I = Vref x 1.25, so 0.8 A needs Vref = 0.64 V. Pololu boards use smaller resistors and a different multiplier.
I = Vref x 2 (with the usual 0.1 Ω resistors), so 1 A needs Vref = 0.5 V.
the formula depends on the module's sense resistors; use the formula in your module maker's manual, or set the current in firmware over UART (Marlin and Klipper both support this).
Set the limit to about 70 to 90% of the motor's rated current to keep it cool.
Swapping drivers on a board or RAMPS
The footprint is shared, but orientation is not obvious. Line up the EN and GND/VMOT pins with the board's labels, not the trimmer position: the DRV8825's trimmer sits on the opposite side from the A4988's. Set microstepping jumpers to match the new driver (the same jumper pattern gives 1/16 on an A4988 but 1/32 on a DRV8825, which halves your steps per millimetre). For TMC2209 in standalone mode, use its MS1/MS2 pins; for UART mode, add the UART wire and enable it in firmware. Always fit a 100 µF capacitor across VMOT and GND near each driver.
Safety tips
- Never connect or disconnect a motor while the driver is powered. The voltage spike destroys the driver instantly.
- Add a heatsink and a fan above about 1 A.
- Power the logic (VDD) from 3.3 or 5 V and the motor (VMOT) from 12 or 24 V; share ground.
- Check the motor's two coil pairs with a multimeter (continuity between wires of the same coil) before wiring.
- See the stepper motors guide for wiring and code, and the steps per mm calculator for machine setup.
Try it: Stepper steps per mm calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Unplugging the motor with power on.
- Leaving Vref at the factory setting.
- Inserting a DRV8825 rotated because its trimmer is on the other side.
- Forgetting the 100 µF capacitor on VMOT.
- Changing driver type without updating microstepping and steps per mm.
Frequently asked questions
Is the TMC2209 better than the A4988?
For most uses, yes: it is much quieter, smoother and runs cooler, and supports sensorless homing. The A4988 is cheaper and simpler for learning.
Can I replace an A4988 with a DRV8825?
Usually yes, as they share the footprint. Check orientation, since the trimmer is on the other side, re-set Vref, and update microstepping and steps per mm.
How do I set Vref on a DRV8825?
Vref = desired current / 2. For a 1.2 A motor at 80%, set about 0.48 V, measured between the trimmer and GND with the board powered.
Why does my stepper motor make noise?
A4988 and DRV8825 drivers switch audibly at low speeds. TMC2209 drivers in StealthChop mode are almost silent. Correct Vref and microstepping also help.
What is sensorless homing?
The TMC2209 detects when the motor stalls against an end stop, so the axis can home without a physical switch. It needs the UART connection and careful tuning.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 3 step-by-step builds in our project library use parts from this guide.
Keep learning
Sources
- Allegro A4988 datasheet
- Texas Instruments DRV8825 datasheet
- Analog Devices (Trinamic) TMC2209 datasheet
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.




