Buying guide · Beginner · 4 min read
3D Printer Nozzles
Brass vs Hardened Steel, Sizes and When to Change
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
Most FDM printers ship with a 0.4 mm brass nozzle, which is right for PLA, PETG, ABS and TPU. Switch to hardened steel (or a ruby or tungsten carbide tip) before printing abrasive filaments such as carbon fibre, glass fibre, glow-in-the-dark or metal fills, which wear brass out within a few hundred grams. Use 0.6 mm for faster, stronger parts and 0.2 mm for fine detail.
Key specs at a glance
- Default
- 0.4 mm brass, M6 thread
- Common sizes
- 0.2, 0.25, 0.4, 0.6, 0.8, 1.0 mm
- Layer height
- Up to about 75% of nozzle diameter (0.3 mm on a 0.4 mm nozzle)
- Line width
- 100 to 120% of nozzle diameter
- Thread types
- MK8 (Creality style), E3D V6, Volcano (longer), plus proprietary quick-swap hot ends
- Abrasive filaments
- Need hardened steel, ruby or tungsten carbide
Brass, hardened steel, stainless or ruby?
| Nozzle material | Heat transfer | Wear resistance | Use it for |
|---|---|---|---|
| Brass | Excellent | Low | PLA, PETG, ABS, ASA, TPU, nylon (unfilled) |
| Plated copper (nickel or similar) | Excellent | Medium | High-temperature work and less sticking of molten plastic |
| Hardened steel | Lower: raise temperature 5 to 15 °C | High | Carbon fibre, glass fibre, glow-in-the-dark, wood and metal fills |
| Stainless steel | Lower | Medium | Cases where you want no lead from brass, such as food-adjacent prototypes |
| Ruby tip or tungsten carbide | Good | Very high | Heavy abrasive printing with good flow |
- Brass
- Heat transfer:
- Excellent
- Wear resistance:
- Low
- Use it for:
- PLA, PETG, ABS, ASA, TPU, nylon (unfilled)
- Plated copper (nickel or similar)
- Heat transfer:
- Excellent
- Wear resistance:
- Medium
- Use it for:
- High-temperature work and less sticking of molten plastic
- Hardened steel
- Heat transfer:
- Lower: raise temperature 5 to 15 °C
- Wear resistance:
- High
- Use it for:
- Carbon fibre, glass fibre, glow-in-the-dark, wood and metal fills
- Stainless steel
- Heat transfer:
- Lower
- Wear resistance:
- Medium
- Use it for:
- Cases where you want no lead from brass, such as food-adjacent prototypes
- Ruby tip or tungsten carbide
- Heat transfer:
- Good
- Wear resistance:
- Very high
- Use it for:
- Heavy abrasive printing with good flow
Which nozzle size should you use?
0.4 mm is the all-rounder: good detail, sensible speed, and every slicer profile assumes it. 0.6 mm prints the same part in roughly two thirds of the time with thicker, stronger walls, and it clogs less with filled filaments. 0.8 mm and 1.0 mm suit vases, large functional parts and drafts. 0.2 to 0.25 mm gives crisp miniatures and small text but is slow and clogs easily.
Two rules keep prints sound: keep the layer height under about 75% of the nozzle diameter, and set the line width between 100 and 120% of it. A bigger nozzle also needs more melt capacity: a standard hot end often cannot melt plastic fast enough for a 0.8 mm nozzle at high speed, which is why Volcano-style long heater blocks exist.
MK8, V6 and Volcano: make sure it fits
Most hobby nozzles use an M6 thread, but lengths differ. MK8 nozzles (Creality Ender 3 and many clones) are shorter than E3D V6 nozzles, and Volcano nozzles are much longer for their tall heater block. Putting the wrong length in leaves a gap between the nozzle and heat break that leaks plastic. Many newer printers (Bambu Lab, Prusa MK4, some Creality K-series) use proprietary quick-swap hot ends with the nozzle and heat break as one part, so buy nozzles made for that model.
How to change a nozzle safely
- 1Heat the hot end to printing temperature (around 230 to 250 °C) so old plastic is soft.
- 2Hold the heater block still with a spanner so you do not twist the wires or the heat break.
- 3Unscrew the old nozzle with a 7 mm socket (V6 and MK8). It is hot: handle it with pliers.
- 4Screw the new nozzle in by hand, then tighten gently at temperature. Snug is enough; over-tightening strips the heater block threads.
- 5Re-run the Z offset or first-layer calibration, because the new nozzle may sit at a slightly different height. See bed levelling.
Clearing a clogged nozzle
Signs of a partial clog are thin, stringy extrusion, clicking from the extruder and gaps in walls. Try these in order:
heat to printing temperature, push some filament through, cool to about 90 °C for PLA (or around 130 °C for nylon cleaning filament), then pull the filament out firmly. The tip brings debris with it. Cleaning filament such as eSUN's natural cleaning filament makes this easier.
a 0.35 mm cleaning needle from below clears small particles in a 0.4 mm nozzle.
nozzles are cheap. If a brass nozzle has a worn, oval or enlarged hole, change it.
Common causes are heat creep (a stopped hot-end fan), printing PLA too hot or too slowly, wet filament, and retraction set too long on a Bowden printer.
Try it: Filament length calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Printing carbon-fibre filament through a brass nozzle; it wears a 0.4 mm hole oversize in a few hundred grams.
- Tightening a nozzle cold, which leaves a gap that leaks once the parts expand.
- Mixing MK8 and V6 nozzles so the nozzle does not seat against the heat break.
- Using hardened steel without raising temperature, which causes under-extrusion.
- Forgetting to update the nozzle size and line width in the slicer after a swap.
Frequently asked questions
What size nozzle is best for 3D printing?
0.4 mm is the best general choice. Use 0.6 mm when you want faster, stronger functional parts and 0.2 to 0.25 mm only for small, detailed prints.
Do I need a hardened steel nozzle?
Only for abrasive filaments: carbon fibre, glass fibre, glow-in-the-dark, metal and some wood fills. For plain PLA, PETG, ABS and TPU, brass prints better and is cheaper.
How often should I change a 3D printer nozzle?
A brass nozzle used with plain filaments can last many months. Replace it when prints show under-extrusion that cleaning does not fix, or when the tip looks worn or rounded.
What layer height can I use with a 0.6 mm nozzle?
Up to about 0.45 mm, though 0.2 to 0.36 mm is the usual range. Keep layer height below roughly three quarters of the nozzle diameter.
Are MK8 and E3D V6 nozzles the same?
Both use an M6 thread, but they are different lengths. Use the type your hot end was designed for, or the nozzle may not seal against the heat break.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
- E3D V6 and Volcano hot end technical documentation
- Prusa Research knowledge base: nozzle types and cold pull
- Filament manufacturer data sheets for abrasive filament nozzle requirements
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


